Makita LH1040 Manual

Makita Rundsave LH1040

Læs gratis den danske manual til Makita LH1040 (36 sider) i kategorien Rundsave. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Makita LH1040, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/36

ENGLISH (Original instructions)

INSTRUCTION MANUAL

DOUBLE INSULATION

IMPORTANT: Read Before Using.

Table Top Miter Saw

LH1040

LH1040F

012649

ENGLISH (Original instructions)

SPECIFICATIONS

Model LH1040 / LH1040F

Blade diameter 255 mm -260 mm

Blade body thickness 1.6 mm - 1.8 mm

Riving knife thickness 2.0 mm

Hole diameter

For all countries other than European countries 25.4 mm and 25 mm

For European countries 30 mm

Max. Cutting capacities (H x W) with blade 260 mm in diameter in the miter saw mode

Miter angle

Bevel angle 0° 45°

69 mm x 130 mm

right 69 mm x 85 mm, 93 mm x 67 mm

0° 93 mm x 95 mm

left 69 mm x 85 mm, 93 mm x 67 mm

35 mm x 130 mm

right 35 mm x 91 mm, 49 mm x 67 mm

45° (left) 53 mm x 95 mm

left 35 mm x 65 mm, 49 mm x 42 mm

Max. Cutting capacities at 90°in the table saw (bench saw mode) 40 mm

No load speed (min-1) 4,800

Table size (W x L) 260 mm x 405 mm

Dimensions (L x W x H) 530 mm x 476 mm x 535 mm

Net weight 14.3 kg

Safety class /II

• Due to our continuing program of research and development, the specifications herein are subject to change without notice.

• Specifications may differ from country to country.

• Weight according to EPTA-Procedure 01/2003

END208-6

Symbols

The following show the symbols used for the equipment.

Be sure that you understand their meaning before use.

･ Read instruction manual.

･ DOUBLE INSULATION

･ To avoid injury from flying debris, keep

holding the saw head down, after

making cuts, until the blade has come to

a complete stop.

･ When using the tool in the miter saw

mode, secure the top table at the

topmost position so that the saw blade

never protrudes from the top surface of

the top table.

･ Do not place hand or fingers close to the

blade.

･ For your safety, remove the chips, small

pieces, etc. from the table top before

operation.

･ Only for EU countries

Do not dispose of electric equipment

together with household waste material!

In observance of the European Directive,

on Waste Electric and Electronic

Equipment and its implementation in

accordance with national law, electric

equipment that have reached the end of

their life must be collected separately

and returned to an environmentally

compatible recycling facility.

ENE060-1

Intended use

The tool is intended for accurate straight cutting and

(only when used as a miter saw on the lower table) miter

cutting in wood.

ENF002-2

Power supply

The tool should be connected only to a power supply of

the same voltage as indicated on the nameplate, and can

only be operated on single-phase AC supply. They are

double-insulated and can, therefore, also be used from

sockets without earth wire.

ENG905-1

Noise

The typical A-weighted noise level determined according

to EN61029:

Produkt Specifikationer

Mærke:	Makita
Kategori:	Rundsave
Model:	LH1040
Bredde:	476 mm
Dybde:	530 mm
Højde:	535 mm
Vægt:	14300 g
Strømforbrug (typisk):	1650 W
Indgangseffekt:	1650 W
Strømkilde:	Vekselstrøm
Tomgang (maks.):	4800 rpm
Kabellængde:	2.5 m
Blad, diameter:	260 mm
Klinge boring:	15.88 mm
Støvpose inkluderet:	Ja
Skærekapacitet 45° gering:	53 x 95 mm
Klippe-kapacitet 0°:	93 mm
Savklingetype:	Tungsten carbide-tipped (TCT)
Skubbepind:	Ja
Bordsav tilstand:	Ja