Makita RP2302FC Manual

Makita Fræsemaskine RP2302FC

Læs gratis den danske manual til Makita RP2302FC (1 sider) i kategorien Fræsemaskine. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Makita RP2302FC, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
I N S T A L L A T I O N I N S T R U C T I O N S
Milestone AV Technologies, and its affiliated corporations and subsidiaries (collectively, "Milestone"), intend to make this manual accurate and complete. However, Milestone makes
no claim that the information contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in connection with the installation or use
of this product. The information contained in this document is subject to change without notice or obligation of any kind. Milestone makes no representation of warranty, expressed or
implied, regarding the information contained herein. Milestone assumes no responsibility for accuracy, completeness or sufficiency of the information contained in this document.
Chief Manufacturing, a products division of Milestone AV Technologies
8401 Eagle Creek Parkway, Savage, MN 55378
• P: 800.582.6480 / 952.894.6280 • F:877.894.6918 / 952.894.6918
8802-000288 Rev01
©2009 Milestone AV Technologies,
a Duchossois Group Company
05/09
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets
SSB-228, SSM-228, SLB-228 and SLM-228 Interface Brackets are designed for use with Chief® Series Projector Mounts. See the specific
installation instructions provided with the mount for additional installation information.
Unpack carton and verify kit contents. If any listed parts are missing, immediately contact a Chief Customer Service representative.
WARNING: IMPROPER INSTALLATION CAN LEAD TO EQUIPMENT FALLING CAUSING SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUIPMENT! DO NOT substitute hardware. Use only hardware supplied by manufacturer!
Installation Instructions
WARNING: OVER TIGHTENING OF SCREWS CAN DAMAGE PARTS AND CAN LEAD TO SERIOUS PERSONAL INJURY AND
DAMAGE TO EQUPIMENT! DO NOT over tighten screws when installing interface brackets.
NOTE: Step 1 is only required when installing an SLB/SSB interface bracket. If an SLM/SSM bracket is being installed, proceed to step 2.
1. Screw thumb screws onto 10-24 x 5/8" Phillips pan head screws. DO NOT fully tighten thumb screws at this time.
2. Turn projector upside down on a flat surface.
3. Place nylon spacers on bottom of projector and align them with threaded inserts.
4. Place the interface bracket onto the bottom of the projector and align it with the holes in the bracket with the threaded inserts and nylon
spacers on the bottom of the projector.
5. Position M4 x 20mm pan head mounting screws with M4 washers, and M4 x 20mm flat head mounting screws into the mounting holes.
Tighten all fasteners at this time, securing the bracket to the projector.
NOTE: Security screws can be substituted when mounting interface bracket to projector by using the parts and installation
instructions in the All-Points Security Kit.
Chief® is a registered trademark of Milestone AV Technologies. All rights reserved.
(1) Interface Bracket (3) Washer, Flat, M4
(4) 10-24 Thumb Nuts ** (3) Screw, Phillips Pan Head, M4 x 20mm
(1) All-Points Security Kit (2) Screw, Phillips Flat Head, M4 x 20mm
(5) Spacer, Nylon, .500 OD x.194 ID x .500
**Only used when installing SLB/SSB interface brackets.
NOTE: Specific to SSB-style and SSM-style interface bracket installation, all appropriate screws come pre-installed as reflected in the
encircled locations above. DO NOT attempt to substitute and USE ONLY this pre-installed hardware for SSB-style and SSM-style
interface bracket installation.
SLB-228 SLM-228
(Note: SSB-style interfac
e
b
r
a
c
k
e
t
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
(
N
o
t
e
:
S
S
M
-
s
t
y
l
e
i
n
t
e
r
f
a
c
e
b
r
a
c
k
e
t
c
o
n
n
e
c
t
i
o
n
s
a
r
e
e
n
c
i
r
c
l
e
d
)
Towards front of
projector
Towards front of
projector

Produkt Specifikationer

Mærke: Makita
Kategori: Fræsemaskine
Model: RP2302FC

Har du brug for hjælp?

Hvis du har brug for hjælp til Makita RP2302FC stil et spørgsmål nedenfor, og andre brugere vil svare dig


Fræsemaskine Makita Manualer

Makita

Makita 3707 Manual

14 Oktober 2024
Makita

Makita BPJ180 Manual

30 August 2024
Makita

Makita 3706 Manual

30 August 2024
Makita

Makita RP2302FC Manual

21 August 2024
Makita

Makita M3600 Manual

6 August 2024
Makita

Makita RT0700C Manual

4 August 2024
Makita

Makita 3612BR Manual

31 Juli 2024
Makita

Makita 3710 Manual

9 Juli 2024

Fræsemaskine Manualer

Nyeste Fræsemaskine Manualer

RIKON

RIKON 23-400 Manual

27 December 2024
Anova

Anova MC360 Manual

23 December 2024
Einhell

Einhell BOF 850E Manual

14 Oktober 2024
Carat

Carat SL-1253 Manual

4 Oktober 2024
Topcraft

Topcraft PRM6010 TBF-1200 Manual

20 September 2024
Bosch

Bosch Groen POF1200AE Manual

8 September 2024
Vonroc

Vonroc S_WC502AC Manual

6 September 2024
Vonroc

Vonroc BJ501AC Manual

6 September 2024
Vonroc

Vonroc WC503AC Manual

6 September 2024
DeWalt

DeWalt D26200 Manual

3 September 2024