Maretron TLM150 Manual

Maretron Ikke kategoriseret TLM150

Læs gratis den danske manual til Maretron TLM150 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Maretron TLM150, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Instructions

TFT-5H SAE 5-Bolt Pattern Non-Displacement Hull Focus Tube

TFT-1.5NPT 1.5” NPT Non-Displacement Hull Focus Tube

TFT-1.25BSP 1.25” BSP Non-Displacement Hull Focus Tube

Packing List

Please find the following items included:

• 1 adapter with focus tube

• 1 focus tube cap with center hole

• 1 packet of epoxy

• 1 wooden mixing stick

Installation on a Tank with a SAE J1810 5-Bolt Fitting and Focus Tube

If a focus tube is used for a tank with sensor mounting hole and use a saw a SAE J1810 5-bolt fitting, determine the depth of the tank at the location of the tank

with a metal-cutting blade to trim the focus tube so that it reaches 1” (2.54cm) above the tank bottom when mounted. Remove any burrs from the end of the focus

tube after trimming. Optionally, install the focus tube cap (see below).

Next, place the gasket included with the focus tube over the focus tube (between the focus tube flange and the tank mounting flange), and then drop the focus

tube into the hole so that the bolt holes on the focus tube, focus tube gasket, and tank fitting all line up (WARNING – the gasket must be properly aligned; it only

fits one way).

Place the gasket included with the TLM100/TLM150 over the focus tube so that the bolt holes line up (WARNING – the gasket must be properly aligned; it only fits

one way), then place the TLM100/TLM150 sensor component on top of the TLM100/TLM150 gasket so that the bolt holes line up.

Insert mounting screws into the bolt holes on the TLM100/TLM150 sensor component, and thread them into the tank fitting (the tank fitting may instead have studs

installed, so in this case, install the nuts over the studs), tightening them to a torque of 10-15 in-lbs (1.1-1.7 N·m). Do not use threadlocking compounds containing

methacrylate ester, such as Loctite Red (271), as they will cause stress cracking of the plastic enclosure.

1” (2.54cm) clearance

between focus tube

and tank bottom

TLM100/TLM150 Interface

Component

Threaded Tank Fitting

Threaded Focus Tube

TLM100/TLM150 Gasket

TLM100/TLM150 Sensor

Component

Mounting Screws (x5)

TLM100/TLM150 Interface

Component

1” (2.54cm) clearance

between focus tube

and tank bottom

SAE 5-Bolt Tank

Fitting

Focus Tube Gasket

Focus Tube

TLM100/TLM150 Sensor

Component

TLM100/TLM150 Gasket

Mounting Screws (x5)

Installation on a Tank with a 1.25”BSP or 1.5”NPT Threaded Tank Fitting and Focus Tube

Figure 1 – Mounting TLM100/TLM150 to SAE 5-Hole Tank with

Focus Tube

Figure 2 – Mounting TLM100/TLM150 with Focus Tube on Threaded Tank

Fitting

If a focus tube is used for a tank with sensor mounting hole and use a saw a SAE J1810 5-bolt fitting, determine the depth of the tank at the location of the tank

with a metal-cutting blade to trim the focus tube so that it reaches 1” above the tank bottom when mounted. Remove any burrs from the end of the focus tube after

trimming. Optionally, install the focus tube cap (see below).