Maytag W10606694 Manual

Maytag Tørretumbler W10606694

Læs gratis den danske manual til Maytag W10606694 (28 sider) i kategorien Tørretumbler. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Maytag W10606694, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/28
W10740674A
Installation Instructions
for W10606694 L.P. (Propane and Butane)
Gas Conversion Kit
Parts included in Kit:
1 Instruction Sheet
1 Blocking Pin
1 Orice, Burner-Butane No. .049
1 Orice, Burner-Propane No. 55
1 Label, Rating Plate Conversion (English)
1 Label, Rating Plate Conversion (French)
1 Label, Conversion Record (English)
1 Label, Conversion Record (French)
1 Label, Burner Baseplate (English/French)
Converting 20,000 BTU/hr Gas Burners from Natural Gas
to Liqueed Petroleum (Bottled Gas)
NOTE: A qualied service technician is any person or
representative of a company who is experienced or trained
in servicing gas equipment and is familiar with necessary
precautions.
IMPORTANT: The LP Conversion Kit you received is an
approved kit for converting your gas dryer from natural to LP
propane or butane gas. The kit number shown on the Burner
Data Label located on the Burner Base may not match the kit
you receive due to kit consolidation.
NOTE: Read these instructions before proceeding.
Canada Only
THIS CONVERSION KIT SHALL BE CARRIED OUT IN
ACCORDANCE WITH THE REQUIREMENTS OF THE
PROVINCIAL AUTHORITIES HAVING JURISDICTION AND
IN ACCORDANCE WITH THE REQUIREMENTS OF THE
CAN-B49.1 AND CAN1-B149.2 INSTALLATION CODE.
Warning: This conversion kit shall be installed by a qualied
service agency in accordance with the manufacturer’s
instructions and all applicable codes and requirements of
the authority having jurisdiction. The information in these
instructions must be followed to minimize the risk of re or
explosion or to prevent property damage, personal injury,
or death. The qualied service agency is responsible for the
proper installation of this kit. The installation is not proper
and complete until the operation of the converted appliance
is checked as specied in the manufacturer’s instructions
supplied with this kit.
This dryer has been manufactured for use with Natural Gas.
Installation of this conversion kit converts the dryer for use
with L.P. gas with supply pressure between 8" (203 mm) and
13" (330 mm) water column. If this dryer is converted for use
with L.P. gas by means of this kit, the input rating will be 20,000
BTU’s per hour, for altitudes up to 10,000 feet (3,048 m). For
installations above 2,000 feet (610 m), contact a qualied
service agency for derating instructions.
Preparing for Kit Installation
READ THOROUGHLY AND FOLLOW STEPS
1. Unplug dryer or disconnect power.
2. Turn off gas supply using the shut-off valve that supplies
the dryer.
3. Fill out information on the appropriate Conversion Record
Label (English or French) and apply in a conspicuous
location adjacent to model and serial tag located in the
door well. Go to Section 1, 2, or 3, depending on model.
Tools and Accessories required:
1/4" Socket and Ratchet Wrench
1/4" Nut Driver
5/16" Nut Driver
Phillips-Head Screwdriver
T-20 Torx®-head Screwdriver†
Pliers or Flat-Head Screwdriver
†® Torx and T-20 are registered trademarks of Acument Intellectual
Properties, LLC.
Disassembling the Dryer
Section
Cabinet
Width
Console
Location
Front Panel
Type
Rated
Capacity
(cubic feet)
Page
1 29" Rear Full 8.8+ 2
2 27" Front Full 7 to 7.5 4
3 29" Rear Full 7 to 7.6 8
4 27" Rear Toe Panel 7 to 7.5 9
2
Disassembling the Dryer
SECTION 1 – 8.8+ CUBIC FOOT MODELS WITH 29" CABINET,
FULL FRONT PANEL, AND REAR CONSOLE
To gain access to inside of dryer:
1. Remove console rear plate and rear shelf plate by
removing a total of eight (8) screws. See Figure 1.
2. Remove two (2) screws from the rear of the top.
See . This will allow the top to be slid rearwardFigure 2 .
3. Disconnect the door switch connector located in the top
left front corner of the dryer. See Figure 3.
4. Remove the front panel and door assembly by removing
a total of eleven (11) screws: Four (4) ¼" hex-head screws
along the bottom front, three (3) Phillips-head screws around
the door opening, and four (4) T-20 Torx-head screws on
the top front panel bracket. See . Once screws are Figure 4
removed, close the door and lift up the front panel and door
assembly to remove.
(3) SCREWS
FIGURE 1
FIGURE 2
FIGURE 3
FIGURE 4
5. Disconnect the drum light connector located in the top left
front corner of the dryer. See . Figure 5
FIGURE 5
(5) SCREWS CONSOLE
REAR
PLATE
REAR
SHELF
PLATE
(2) SCREWS
DOOR SWITCH
CONNECTOR
(3) SCREWS
(4) SCREWS
FRONT
PANEL
DRUM LIGHT
CONNECTOR
TOP
(4) SCREWS

Produkt Specifikationer

Mærke: Maytag
Kategori: Tørretumbler
Model: W10606694

Har du brug for hjælp?

Hvis du har brug for hjælp til Maytag W10606694 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Tørretumbler Maytag Manualer

Maytag

Maytag MED7405RR Manual

16 September 2025
Maytag

Maytag MGD7405RR Manual

5 September 2025
Maytag

Maytag MED6205RR Manual

5 September 2025
Maytag

Maytag RMED4500MW Manual

4 September 2025
Maytag

Maytag MED5430PBK Manual

27 August 2025
Maytag

Maytag MED7020RU Manual

16 August 2025
Maytag

Maytag MED7020RF Manual

16 August 2025
Maytag

Maytag MGD7020RF Manual

16 August 2025
Maytag

Maytag MGDP576KW Manual

27 Juli 2025
Maytag

Maytag MGD4005SW Manual

17 Februar 2025

Tørretumbler Manualer

Nyeste Tørretumbler Manualer

Electrolux

Electrolux TD6-17S Manual

2 Oktober 2025
ElectriQ

ElectriQ Eiqtd7black Manual

2 Oktober 2025
Samsung

Samsung DV90DG6845LHU Manual

2 Oktober 2025
Philco

Philco PDCI 8 E King Manual

2 Oktober 2025
Samsung

Samsung DV90DG6845LE Manual

2 Oktober 2025
Kernau

Kernau KFD 8423 Manual

1 Oktober 2025
Samsung

Samsung DV90DG52A0TE Manual

1 Oktober 2025
LG

LG DLEX5800A Manual

1 Oktober 2025
Electrolux

Electrolux EDI61X84G Manual

1 Oktober 2025
Insignia

Insignia NS-TDRE67W1 Manual

1 Oktober 2025