Megasat ST-25 FP Manual

Megasat Pengeskab ST-25 FP

Læs gratis den danske manual til Megasat ST-25 FP (2 sider) i kategorien Pengeskab. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Megasat ST-25 FP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Security safe with ngerprint scanner (FP series)

Please emergency key

do not store in a safe

Schematic view of the safe Schematic view of the control panel

1. Registration button

(Model-dependent)

2. Locking bolt

3. Battery compartment

4. Number keys

5. Door handle

6. Fingerprint scanner

7. Unlocking button

8. Emergency unlocking cover

• Locks: with high quality anti-drill locking bolts - especially theft-proof.

• Registration scanner: ngerprint registration or ngerprint data deletion

• Unlock key: Opens the safe

• Fingerprint scanner: Fingerprint enrolment

• Separate numeric keys on the control panel for entering codes (1, 2, 3, 4)

• Key for code registration („1“) Depending on the model, in the battery compartment or in the side door

• Cover: remove the cover and open the safe using the emergency lock

• Power supply: 4x AA batteries

• Remove the emergency lock cover

• Insert the emergency key into the lock and turn it clockwise.

• Now turn the door handle clockwise and open the door.

When you use the safe for the rst time or if you forget the code or ngerprint is not recognised, you can use

the emergency key to open the safe.

Press the registration key (registration key) for approx. 5 seconds, the green indicator lamp will icker (approx.

12 times). While doing so, hold the emergency key in the unlocking position. Release the key again when the

patching has stopped. A long „tick“ can be heard, all ngerprints and codes are deleted and the data set at the

factory are loaded. (code 1234)

ATTENTION: If the key is lost, it can only be re-ordered (for security reasons) using the serial number on the

inside of the safe. Please note this number in a safe place. If the key is lost and the code and serial number are

unknown, the safe can only be opened by force.

• Do not use liquid cleaners or sprays to clean the safe.

• Use a damp cloth instead.

• Do not place the product on unsafe and elevated objects to prevent it from falling down and injuring the product

or people.

• Never spill liquid on the control panel, as it may cause electrical damage to the electronic components and aect

their proper functioning.

• Never attempt to disassemble the product yourself. Improper disassembly and damage to the inside and rear

panel, can damage the electrical circuitry and aect its proper function.

• If maintenance is required, please contact your local service centre or local dealer.

• The ST series is a high-tech product for better security.

• Use the ngerprint instead of a key for greater convenience

• A maximum of 20 ngerprints can be registered

• Constructed of solid material - protected against hand and power tools

• User-friendly product design - unique structure

FUNCTIONS

EMERGENCY KEY

DELETE SYSTEM INITIALISATION

IMPORTANT NOTES

FEATURES

ATTENTION: For your absolute security, please pay attention to the emergency key and keep the key in a secret

place.

Version: 1.2 May 2023 // Technical changes, printing errors and mistakes reserved.

Conformity information:

Megasat Werke GmbH hereby declares that the following equipment is in conformity with the essential require-

ments and the other relevant provisions of Directive EMV 2014/30/EU:

Megasat ST-20 FP (Art-No. 0900088) / Megasat ST-30 FP (Art-No. 0900089) / Megasat ST-50 FP (Art-No. 0900090)

The declaration of conformity for these products is available:

Megasat Werke GmbH, Brückenstraße 2a, D-97618 Niederlauer.

You can download the declaration of conformity from our homepage: www.megasat.tv/support/downloads

Megasat Werke GmbH - Brückenstraße 2a - 97618 Niederlauer

Press the numeric key „1“ for about 5 seconds and the green indicator lamp lights up. Enter the old code (factory

setting 1234) and press the release key (unlock key). A short signal tone sounds. „Beep“, enter the new code (4

to 8 digits) and press the unlock key. Another short signal tone sounds. Enter the new code again and conrm

with the unlock key. If the code is entered correctly, a long signal tone sounds. The new code is now registered

and can be used. ATTENTION: The factory setting code is: 1234

• The safe is delivered without registered ngerprints.

• The safe is not equipped with batteries. To open the door for the rst time you can use the emergency lock

with the emergency key under the cover.

• At the back of the door open the battery compartment and insert 4x AA (good quality) batteries. Please

observe the polarity of the batteries. Under normal use, the batteries will last for about one year.

• The default code on delivery is „1234“. After inserting the batteries, you can open the door with this code.

Unlocking via ngerprint

Press the share key, the red light on the nger scanner will light up. Place your nger straight and in the middle

of the scanner. If the ngerprint is correct, you will hear a beep and the lock will unlock. The green LED lights up.

Within 5 seconds you can now open the lock. To do this, turn the handle clockwise and open the door. The lock

locks automatically after 5 seconds if the safe has not been opened. To close the safe, simply close the door and

turn the handle counter-clockwise again. The system automatically locks the door.

NOTE: If no ngerprints are registered, the red scanner will not light up.

Unlocking via a code

Enter the code (4 to 8 digits) using the number keys and press the enable key to conrm. If the code is entered correc-

tly, a signal tone sounds and the green LED lights up. The lock is unlocked. Please turn the knob clockwise and open

the door within 5 seconds. The lock locks automatically after 5 seconds if the safe has not been opened. To close

the safe, simply close the door and turn the knob counterclockwise again. The system automatically locks the door.

If an incorrect entry is made, several short beeps will sound and the LED will light up red.

ATTENTION: To improve the current rate of nger identication, please note the following information:

Do not expose the scanner to harsh light when scanning. We recommend each user to enrol 2-3 ngerprints.

For female users and children, we suggest to register thumb and middle nger. Do not press too hard on the

scanner, a light pressure is sucient. In very dry air and hands, you can breathe on the nger to improve the

result.

• Open the door.

• Pull o the battery cover to the left.

• Insert 4 new „AA“ batteries and observe the correct polarity, marked with the „+“ and „-“ signs.

• Press the logon key and you will hear two short beeps „Beep, beep“.

• The red light of the nger scanner lights up. Place your nger on the scanner surface within two seconds.

You will again hear two short signal tones „Beep, beep“.

• After about 1 second, a long „beep“ follows, which means that the ngerprint registration is successful.

However, if you hear 3 short „beep, beep, beep“ signal tones, this indicates a registration error.

• After this method you can register more ngerprints.

ATTENTION: For security reasons you should denitely change the preset code.

Correct:

Wrong:

ATTENTION: If the LED turns red when in use, this means that the batteries are low and need to be replaced.

When selecting batteries, we recommend using high-power alkaline batteries of high quality. Please do not use

low quality zinc-carbon batteries.

ATTENTION: A maximum of 20 ngerprints can be registered.

PREPARATION UNLOCKING AND OPENING THE SAFE

CHANGING BATTERIES

THE FINGERPRINT REGISTRATION

SET USER CODE

Produkt Specifikationer

Mærke:	Megasat
Kategori:	Pengeskab
Model:	ST-25 FP

Har du brug for hjælp?

Hvis du har brug for hjælp til Megasat ST-25 FP stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Pengeskab Megasat Manualer

Megasat ST 50 K Manual

1 Juli 2025

Megasat ST-100 Manual

1 Juli 2025

Megasat ST-25 FP Manual

30 Juni 2025

Megasat ST 30 FP Manual

29 Juni 2025

Megasat ST 25 K Manual

29 Juni 2025

Megasat ST 50 FP Manual

28 Juni 2025

Pengeskab Manualer

Nyeste Pengeskab Manualer

Sentry HD2100 Manual

2 Oktober 2025

Sentry X055 Manual

29 September 2025

Kogan KADSAFSA9LA Manual

30 August 2025

Suncast BMCCPD8004 Manual

27 August 2025

Kasp K60175D Manual

21 August 2025

Stamony ST-KS-400 Manual

17 August 2025

Philips SBX301 Manual

15 August 2025

Philips SBX701B7S0 Manual

15 August 2025

Philips SBX701B8S0 Manual

15 August 2025

Philips SBX701B4G0 Manual

15 August 2025