Mercusys MS108GP Manual

Mercusys Ikke kategoriseret MS108GP

Læs gratis den danske manual til Mercusys MS108GP (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Mercusys MS108GP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

LED Explanation

Note: For simplicity, we will take MS108GP for example.

Switch Explanation

O: Ports run at 1000/100/10 Mbps (100/10 Mbps for MS110P) and support PoE power

supply up to 100m away.

On: Ports run at 10 Mbps and support PoE power supply up to 250m away.

Extend (for MS105GP/MS108GP/MS110P)

O: The PoE Auto Recovery function is disabled.

On: The switch will constantly detect the working status of a PoE powered device (PD).

When the switch nds that the PD works abnormally, the switch will reboot it.

Recovery (For MS110P)

O: Ports can transmit data with each other.

On: Specic ports cannot transmit data with other downlink ports. They can transmit data

only with the uplink ports (port 5 of MS105GP/port 8 of MS108GP/ports 9-10 of

MS110P).

Isolation (For MS105GP/MS108GP/MS110P)

PoE Switch

Quick Installation Guide

For technical support, replacement services, user guides, and other

information, please visit https://www.mercusys com/support/..

DC P er Adapterow

AC Power Cord

Connection

Ethernet Ports (1-8)

PoE Ports (1-7)

1. PoE ports can also connect to non-PoE devices, but only transmit data.

2. Non-PoE ports (port 5 of MS105GP/port 8 of MS108GP/ports 9-10 of MS110P) are

recommended to connect to uplink devices like routers.

3. Ports 1-2 have higher priority than other ports in transmitting data if network

congestion occurs. It is recommended to connect key network devices (network

cameras, APs, etc.) to ports 1-2.

Notes:

Internet

IP Camera AP IP Phone

Powered Device (PD)

Power

On: The power is on

O: The power is o

Link/Act

On:

Link present but no activity

Flashing:

Transmitting or receiving data

O:

No link

PoE Status

On:

PoE power provided

O:

No PoE power provided

Note: For MS108GP, the Power LED is on the top right of port 8.

Mercusys hereby declares that the device is in compliance with the essential

requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU,

2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at

https://www.mercusys.com/en/ce/

EU declaration of conformity

General Specications

Specications

IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab (for MS105GP and

MS108GP), IEEE 802.3x

CSMA/CD. 802.3af/at PD supported

MS105GP:

5 1000 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX

PoE Ports: Port 1–4

MS108GP:

8 1000 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX

PoE Ports: Port 1–7

MS110P:

10 10/100 Mbps RJ45 Ports Auto-Negotiation/Auto MDI/MDIX

PoE Ports: Port 1–8

10BASE-T:2-pair UTP/STP (≤100m) of Cat. 3 or above

100BASE-TX:2-pair UTP/STP (≤100m) of Cat. 5 or above

1000BASE-T:4-pair UTP/STP (≤100m) of Cat. 5e or above

MS105GP: 10 Gbps

MS108GP: 16 Gbps

MS110P: 2 Gbps

8K (only for MS108GP)

Store-and-Forward

Automatically learning, automatically aging

External Power Adapter

Input: 100-240 VAC, 50/60 Hz

Output:

53.5 VDC/1.31 A

65 W (up to 30 W for each PoE port)

Standard

Network Media (Cable)

MAC Address Table

Interface

Switching Capacity

Protocol

Power Supply

Forwarding Method

MAC Address Learning

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. If you need service,

please contact us.

Place the device with its bottom surface downward.

Do not use damaged charger or USB cable to charge the device.

Do not use any other chargers than those recommended.

Adapter shall be installed near the equipment and shall be easily accessible.

The plug on the power supply cord is used as the disconnect device, the

socket-outlet shall be easily accessible.

PoE Budget

Frequently Asked Questions (FAQ)

The Power LED should be lit when the power system is working normally. If the Power

LED is not lit, please check as follows:

A1:

Make sure the AC power cord/power adapter is connected the switch with power

source properly.

A2:

Make sure the voltage of the power supply meets the requirements of the input

voltage of the switch.

A3:

Make sure the power source is on.

Q1. Why is the Power LED not lit?

It is recommended that you check the following items:

A1:

Make sure that the cable connectors are rmly plugged into the switch and the

device.

A2:

Make sure the connected device is turned on and working well.

A3:

The cable must be less than 100 meters long (328 feet). If Extend Mode is enabled,

it should be less than 250 meters (820 feet).

Q2. Why is the Link/Act LED not lit when a device is

connected to the corresponding port?

When the total power consumption of connected PoE devices exceeds the maximum,

the PoE port with a smaller port number has a higher priority. The system will cut o

power to the ports with larger port numbers to ensure supplying to other ports.

Take MS108GP as an example. If port 1, 2 and 4 are consuming 18 W respectively, and

an additional PoE device with 15 W is inserted to port 3, the system will cut o the

power of port 4 to compensate for the overload.

Q3. Why are PoE ports not supplying power for PoE devices?

A1:

Before upgrading a connected PoE powered device (PD), disable PoE Auto

Recovery to avoid the PD’s damage.

A2:

When a PD does not send data packets to the switch for a long period in certain

scenarios (e.g. an IPC in sleep mode), disable PoE Auto Recovery to avoid the PD

repeatedly rebooting.

Q4. What should I notice before using the PoE Auto Recovery

feature?

Environmental and Physical Specications

CE, RoHS

0˚C to 40˚C (32˚F to 104˚F)

-40˚C to 70˚C (-40˚F to 158˚F)

10% to 90% non-condensing

5% to 90% non-condensing

Certication

Operating Temperature

Storage Temperature

Operating Humidity

Storage Humidity

Mercusys hereby declares that the device is in compliance with the essential

requirements and other relevant provisions of the Electromagnetic Compatibility

Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.

The original UK declaration of conformity may be found at

https://www.mercusys.com/support/ukca/

UK declaration of conformity

Produkt Specifikationer

Mærke:	Mercusys
Kategori:	Ikke kategoriseret
Model:	MS108GP
Vekselstrømsindgangsspænding:	220 V
Vekselstrømsindgangsfrekvens:	50 Hz
Bredde:	171 mm
Dybde:	98 mm
Højde:	27 mm
Produktfarve:	Sort
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 95 %
Strømforbrug (typisk):	5.07 W
Driftstemperatur (T-T):	0 - 40 °C
Husmateriale:	Metal
Hurtig start guide:	Ja
Kabler inkluderet:	Vekselstrøm
Strømkilde:	Vekselstrøm
Strømforbrug (maks.):	77.33 W
Netværksstandarder:	IEEE 802.3af, IEEE 802.3at, IEEE 802.3x
Webbaseret administration:	Ja
Kan monteres på væggen:	Ja
Indgangsspænding:	53.5 V
Indgangsstrøm:	1.31 A
Fuld duplex:	Ja
Strøm over Ethernet (PoE):	Ja
Switch-type:	Administreret
Power over Ethernet plus (PoE+) porte, antal:	1
Power over Ethernet (PoE) effekt pr. port:	65 W
10G understøttelse:	Ingen
Auto MDI/MDI-X:	Ja
Flowkontrol support:	Ja
Basis omskiftning RJ-45 Ethernet porte, antal:	8
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
Opbevar-og-frem:	Ja
MAC adresselabel:	8000 entries
Switch kapacitet:	- Gbit/sek.
Stativ-montering:	Ingen
Varmeafgivelse:	262.922 BUT/t
Trafik klassificering:	Ja
Power over Ethernet (PoE) porte, antal:	7
Strømforsyning inkluderet:	Ja
Halv dupleks:	Ja
Stabelbar:	Ingen
Politikbaseret routing:	Ja