Mercusys MS116GS Manual

Mercusys Ikke kategoriseret MS116GS

Læs gratis den danske manual til Mercusys MS116GS (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 25 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 13 anmeldelser. Har du et spørgsmål om Mercusys MS116GS, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
16-Port Gigabit Desktop/Rackmount Switch
*Images may dier from actual product.
Quick Installation Guide
© 2024 MERCUSYS 7107500323 REV1.0.0
For technical support, replacement services, and other information,
please visit https://www.mercusys com/support/..
To install the device on a desktop, follow these steps:
a. Place the device on a stable, at surface that can support its full
weight, including all ttings.
b. Remove the adhesive backing papers from the rubber feet.
1. Install the Switch
a. Check the eciency of the grounding system and the stability of the rack.
b. Secure the supplied rackmount brackets to each side of the device
with the supplied screws, as illustrated in the following gure.
Option 2. Rack Installation
To install the device in an EIA standard-sized, 19-inch rack, follow the instructions described below:
Option 1. Desktop Installation
2. Connect the Switch
b. Plug the negative connector of the provided power cord into the
power socket of the device and plug the positive connector into a
power outlet, as shown in the gure below.
a. Connect an Ethernet port of the switch to the computer using an
RJ45 Ethernet cable, as shown in the gure below.
c. After the brackets are attached to the device, use suitable screws (not
provided) to secure the brackets to the rack, as illustrated in the
following gure.
c. Turn over the device and attach the supplied rubber feet to the
recessed areas at each corner on the bottom of the device.
Caution:
• Maintain a 5 to 10cm gap around the devices for proper air circulation.
• Avoid placing heavy objects on the device.
• Mount devices in sequence from the bottom to top of the rack and ensure a certain clearance between devices for the purpose of heat dissipation.
Mercusys hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU,
2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at
https://www.mercusys.com/en/ce/
EU declaration of conformity Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
Place the device with its bottom surface downward.
The socket-outlet shall be installed near the equipment and shall be easily accessible.
The plug on the power supply cord is used as the disconnect device, the
socket-outlet shall be easily accessible.
Plug the product into the wall outlets with earthing connection through the power
supply cord.
Frequently Asked Questions (FAQ)
The Power LED should be lit when the power system is working normally. If the Power
LED is not lit, please check the following:
A1:
Ensure the AC power cord/power adapter is securely connected to both the switch
and the power source.
A2:
Verify that the power supply's voltage meets the requirements of the switch's input
voltage.
A3:
Conrm that the power source is on.
Q1. Why is the Power LED not lit?
It is recommended that you check the following:
A1:
Ensure the cable connectors are securely plugged into both the switch and the
connected device.
A2:
Verify that the connected device is powered on and functioning properly.
A3:
Conrm that the cable length does not exceed 100 meters (328 feet).
Q2. Why is the Link/Act LED not lit when a device is
connected to the corresponding port?
Specications
IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x,
IEEE 802.1p
16×10/100/1000Mbps RJ45 Ports, Auto Negotiation/Auto
MDI/MDIX
10BASE-T: UTP category 3, 4, 5 cable (maximum 100m)
100BASE-TX/1000BASE-T: UTP category 5, 5e, or above cable
(maximum 100m)
32 Gbps
8K
Store-and-Forward
100-240VAC, 50/60Hz
General Specications
Standard
Network Media (Cable)
MAC Address Table
Interface
Switching Capacity
Forwarding Method
Power Supply
Environmental and Physical Specications
CE, RoHS
0˚C to 40˚C (32˚F to 104˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90% non-condensing
5% to 90% non-condensing
Certication
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
Mercusys hereby declares that the device is in compliance with the essential
requirements and other relevant provisions of the Electromagnetic Compatibility
Regulations 2016 and Electrical Equipment (Safety) Regulations 2016.
The original UK declaration of conformity may be found at
https://www.mercusys.com/support/ukca/
UK declaration of conformity
Button Explanation
O (Default) The switch will not try to monitor or address loop-related issues.:
On: The switch will monitor and address loop-related issues within the network
structure to prevent disruptions caused by redundant pathing.
Loop Prevention
Isolation
O (Default) Ports can transmit data with each other.:
On: Specic ports cannot transmit data with other downlink ports. They can transmit
data only with the uplink ports.
Note: When the isolation button is on, the isolated ports act as downlink ports with the rest as uplink ports.
LED Explanation
Power
On: The switch is powered on.
O: The switch is powered o or power supply is abnormal.
Flashing: Power supply is abnormal or Loop Prevention function is enabled.
1000Mbps
On: Running at 1000 Mbps.
O: Running at 10/100 Mbps or no device is linked to the corresponding port.
Link/Act Status
On: A device is linked to the corresponding port and running properly.
O: No device is linked to the corresponding port.
Flashing: Transmitting or receiving data.

Produkt Specifikationer

Mærke: Mercusys
Kategori: Ikke kategoriseret
Model: MS116GS

Har du brug for hjælp?

Hvis du har brug for hjælp til Mercusys MS116GS stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Mercusys Manualer

Mercusys

Mercusys MS106P Manual

6 Juni 2025
Mercusys

Mercusys MS124GS Manual

4 Juni 2025
Mercusys

Mercusys MS110CMP Manual

4 Juni 2025
Mercusys

Mercusys MS118CP Manual

3 Juni 2025
Mercusys

Mercusys MA310E Manual

3 Juni 2025
Mercusys

Mercusys MS110GMP Manual

3 Juni 2025
Mercusys

Mercusys MA80XE Manual

3 Januar 2025
Mercusys

Mercusys MA14N Manual

24 December 2024
Mercusys

Mercusys MS116GS Manual

23 December 2024
Mercusys

Mercusys MA30H Manual

3 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Simrad

Simrad Active Imaging HD (Thru-Hull) Manual

14 Juni 2025
Garritan

Garritan Harps Manual

14 Juni 2025
Marshall

Marshall CV-H20-HF Manual

14 Juni 2025
Aiphone

Aiphone IXW-MAA Manual

14 Juni 2025
Rival

Rival HM-743 Manual

14 Juni 2025
Lutec

Lutec Avony Manual

14 Juni 2025
Giordani

Giordani G-SAFE & PLAY Manual

14 Juni 2025
Gourmia

Gourmia GAF799 Manual

14 Juni 2025
Arendo

Arendo 307503 Manual

14 Juni 2025
Hughes & Kettner

Hughes & Kettner Tube 100 Manual

14 Juni 2025