Metabo N5024A2 Manual

Metabo Hæftemaskine N5024A2

Læs gratis den danske manual til Metabo N5024A2 (60 sider) i kategorien Hæftemaskine. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Metabo N5024A2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/60
Model Stapler
Modèle Agrafeuse
Modelo Grapadora
Instruction and safety manual
Manuel d’instructions et de sécurité
Instrucciones y manual de seguridad
N 5024A2 • N 5021A
DANGER
Improper use of this Stapler can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Stapler.
Never allow anyone who has not reviewed this manual to use the tool.
This manual should be stored in safe place.
DANGER
Une utilisation incorrecte et sans respecter la sécurité de cette agrafeuse risque d’entraîner
la mort ou des blessures graves !
Ce manuel renferme des instructions importantes sur la sécurité de l’outil.
Lire et bien assimiler ce manuel avant d’utiliser l’agrafeuse.
Cet outil ne doit jamais être utilisé par une personne n’ayant pas pris connaissance du manuel.
Ce mode d’emploi doit être conservé dans un endroit sûr.
PELIGRO
¡La utilización inadecuada e insegura de esta grapadora puede resultar en lesiones serias
o en la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y entienda este manual antes de utilizar la grapadora.
La herramienta no deberá utilizarse sin haber leído previamente este manual.
Este manual debe ser guardado en un lugar seguro.
ATTENTION : USERS OF metabo HPT NAILERS
(Read this information carefully for your satisfaction and safety)
This metabo HPT nailer has a STANDARD CONTACT TRIP MECHANISM (Bounce Fire). An OPTIONAL
SEQUENTIAL TRIP MECHANISM kit (SINGLE SHOT) is available as shown below.
Models Order part number
NR83A, NR83AA, NV83A, NV65AC, VH-650, NT65A2, NV50AA, NV50A1, NV50AP,
NR83AA2, N5008AC, NV50AP2, NV83A2, N5024A, N5010A, N5021A, N5008AC2, N5024A2
876762
NV45AB, NV45AB2, NV45AE 878226
NR90AC, NV65AH, NR90AA, NV45AC, NR90AC2 881973
NT65AA, NT65MA 880414
NV75AG 883991
To order in U.S. call toll free 1-800-706-7337. In Canada call toll free 1-800-970-2299.
THE STANDARD CONTACT TRIP MECHANISM (Bounce Fire) is for use where rapid fastener placement is desired
and must be operated in accordance with the following “Methods of Operation”.
This metabo HPT nailer is equipped with a push lever and does not operate unless the push lever is depressed
(upward position). There are two methods of operation to drive nails with this Nailer.
1. Intermittent operation (Trigger Fire)
2. Continuous operation (Push Lever Fire)
(1) Intermittent operation (Trigger Fire)
1
Position the nail outlet on the workpiece with fi
nger o
ff the trigger.
2
Depress the push lever fi rmly until it is completely depressed.
3
Pull the trigger to drive a nail.
4
Remove fi nger from the trigger.
To drive another nail, move the nailer along the workpiece and repeat this procedure.
(2) Continuous operation (Push Lever Fire)
1
Pull the trigger with the push lever pointing towards but not touching the workpiece.
2
Depress the push lever against the workpiece to drive a nail.
3
Move the nailer along the workpiece with a bouncing motion. Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven, remove fi nger from the trigger.
WAR NING
: Keep your fi nger off the trigger except during fastening operation, because serious
injury could result if the push lever accidentally contacts you or others in work area.
WAR NING
: Keep hands and body away from the discharge area. The nailer with contact trip
mechanism may bounce from the recoil of driving a fastener and unwanted subsequent
fastener may be driven, possibly causing injury.
THE OPTIONAL SEQUENTIAL TRIP MECHANISM (SINGLE SHOT PARTS) is for use where precision fastener
placement is desired and must be operated in accordance with the following “Method of Operation”.
You must fi rst depress the push lever (upward position) where you want to drive a nail and then pull
the trigger. After the each nail is driven, completely release the trigger and lift the tool off the work surface. An
OPTIONAL SEQUENTIAL TRIP MECHANISM may reduce the possibility of bodily injury to you or others in the
work area. This is because it is less likely to drive an unwanted nail if you keep the trigger pulled and accidentally
bump the push lever against yourself or others. An OPTIONAL SEQUENTIAL TRIP MECHANISM may also reduce
the speed of operation compared to the standard contact trip mechanism.
NOTE : Both STANDARD CONTACT TRIP MECHANISM and OPTIONAL SEQUENTIAL TRIP MECHANISM are safe if
used as described above and according to all warnings and instructions.
2
English

Produkt Specifikationer

Mærke: Metabo
Kategori: Hæftemaskine
Model: N5024A2

Har du brug for hjælp?

Hvis du har brug for hjælp til Metabo N5024A2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Hæftemaskine Metabo Manualer

Metabo

Metabo NP35A Manual

24 August 2024
Metabo

Metabo NR83A5Y Manual

24 August 2024
Metabo

Metabo NR1890DR Manual

24 August 2024
Metabo

Metabo NV65AN Manual

24 August 2024
Metabo

Metabo NT65M2S Manual

24 August 2024
Metabo

Metabo NR83A5S1 Manual

24 August 2024
Metabo

Metabo NT50A5 Manual

24 August 2024
Metabo

Metabo NR90AC5 Manual

24 August 2024
Metabo

Metabo NR1890DRS Manual

24 August 2024
Metabo

Metabo NT1850DES Manual

24 August 2024

Hæftemaskine Manualer

Nyeste Hæftemaskine Manualer

Swingline

Swingline Speed Pro 25 Manual

15 Juni 2025
Swingline

Swingline S7066525 Manual

11 Juni 2025
Swingline

Swingline High Capacity Manual

11 Juni 2025
Swingline

Swingline Optima Grip Manual

11 Juni 2025
Swingline

Swingline S7006701 Manual

10 Juni 2025
Swingline

Swingline Optima 20 Manual

10 Juni 2025
Swingline

Swingline Optima 70 Manual

10 Juni 2025
Swingline

Swingline Optima 45 Manual

10 Juni 2025
Novus

Novus J-165 Panel Manual

10 Juni 2025
Novus

Novus J-214 Li-Ion Manual

10 Juni 2025