Metabo NV50A1 Manual

Metabo Hæftemaskine NV50A1

Læs gratis den danske manual til Metabo NV50A1 (69 sider) i kategorien Hæftemaskine. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Metabo NV50A1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/69
Instruction and safety manual
Manuel d’instructions et de sécurité
Instrucciones y manual de seguridad
Model
Modèle
Modelo NV 83A2 • NV 65AC • NV 50A1 Nailer
Cloueur
Clavador
NV83A2 NV65AC NV50A1
DANGER
Improper use of this Nailer can result in death or serious injury!
This Manual contains important information about product safety.
Read and understand this Manual before operating the Nailer.
Never allow anyone who has not reviewed this manual to use the tool.
This manual should be stored in safe place.
DANGER
Une utilisation incorrecte et sans respecter la sécurité de ce cloueur risque d’entraîner la
mort ou des blessures graves !
Ce manuel renferme des instructions importantes sur la sécurité de l’outil.
Lire et bien assimiler ce manuel avant d’utiliser le cloueur.
Cet outil ne doit jamais être utilisé par une personne n’ayant pas pris connaissance du manuel.
Ce mode d’emploi doit être conservé dans un endroit sûr.
PELIGRO
¡La utilización inadecuada e insegura de este clavador puede resultar en lesiones serias o
en la muerte!
Este manual contiene información importante sobre la seguridad del producto.
Lea y entienda este manual antes de utilizar el martillo neumático.
La herramienta no deberá utilizarse sin haber leído previamente este manual.
Este manual debe ser guardado en un lugar seguro.
2
English
ATTENTION : USERS OF metabo HPT NAILERS
(Read this information carefully for your satisfaction and safety)
This metabo HPT nailer has a STANDARD CONTACT TRIP MECHANISM (Bounce Fire). An OPTIONAL
SEQUENTIAL TRIP MECHANISM kit (SINGLE SHOT) is available as shown below.
Models Order part number
NR83A, NR83AA, NV83A, NV65AC, VH-650, NT65A2, NV50AA, NV50A1, NV50AP,
NR83AA2, N5008AC, NV50AP2, NV83A2, N5024A
876762
NV45AB, NV45AB2, NV45AE 878226
NR90AC, NV65AH, NR90AA, NV45AC, NR90AC2 881973
NT65AA, NT65MA 880414
NV75AG 883991
To order in U.S. call toll free 1-800-706-7337. In Canada call toll free 1-800-970-2299.
THE STANDARD CONTACT TRIP MECHANISM (Bounce Fire) is for use where rapid fastener placement is
desired and must be operated in accordance with the following “Methods of Operation”.
This metabo HPT nailer is equipped with a push lever and does not operate unless the push lever is depressed
(upward position). There are two methods of operation to drive nails with this Nailer.
1. Intermittent operation (Trigger Fire)
2. Continuous operation (Push Lever Fire)
(1) Intermittent operation (Trigger Fire)
1
Position the nail outlet on the workpiece with fi nger off the trigger.
2
Depress the push lever fi rmly until it is completely depressed.
3
Pull the trigger to drive a nail.
4
Remove fi nger from the trigger.
To drive another nail, move the nailer along the workpiece and repeat this procedure.
(2) Continuous operation (Push Lever Fire)
1
Pull the trigger with the push lever pointing towards but not touching the workpiece.
2
Depress the push lever against the workpiece to drive a nail.
3
Move the nailer along the workpiece with a bouncing motion. Each depression of the push lever will drive a nail.
As soon as the desired number of nails have been driven, remove fi nger from the trigger.
WAR NING
: Keep your fi nger off the trigger except during fastening operation, because serious
injury could result if the push lever accidentally contacts you or others in work area.
WAR NING
: Keep hands and body away from the discharge area. The nailer with contact trip
mechanism may bounce from the recoil of driving a fastener and unwanted subsequent
fastener may be driven, possibly causing injury.
THE OPTIONAL SEQUENTIAL TRIP MECHANISM (SINGLE SHOT PARTS) is for use where precision fastener
placement is desired and must be operated in accordance with the following “Method of Operation”.
You must fi rst depress the push lever (upward position) where you want to drive a nail and then pull the trigger.
After the each nail is driven, completely release the trigger and lift the tool off the work surface. An OPTIONAL
SEQUENTIAL TRIP MECHANISM may reduce the possibility of bodily injury to you or others in the work area. This
is because it is less likely to drive an unwanted nail if you keep the trigger pulled and accidentally bump the push
lever against yourself or others. An OPTIONAL SEQUENTIAL TRIP MECHANISM may also reduce the speed of
operation compared to the standard contact trip mechanism.
NOTE : Both STANDARD CONTACT TRIP MECHANISM and OPTIONAL SEQUENTIAL TRIP MECHANISM are safe
if used as described above and according to all warnings and instructions.

Produkt Specifikationer

Mærke: Metabo
Kategori: Hæftemaskine
Model: NV50A1

Har du brug for hjælp?

Hvis du har brug for hjælp til Metabo NV50A1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Hæftemaskine Metabo Manualer

Metabo

Metabo NP35A Manual

24 August 2024
Metabo

Metabo NR83A5Y Manual

24 August 2024
Metabo

Metabo NR1890DR Manual

24 August 2024
Metabo

Metabo NV65AN Manual

24 August 2024
Metabo

Metabo NT65M2S Manual

24 August 2024
Metabo

Metabo NR83A5S1 Manual

24 August 2024
Metabo

Metabo NT50A5 Manual

24 August 2024
Metabo

Metabo NR90AC5 Manual

24 August 2024
Metabo

Metabo NR1890DRS Manual

24 August 2024
Metabo

Metabo NT1850DES Manual

24 August 2024

Hæftemaskine Manualer

Nyeste Hæftemaskine Manualer

Swingline

Swingline Speed Pro 25 Manual

15 Juni 2025
Swingline

Swingline S7066525 Manual

11 Juni 2025
Swingline

Swingline High Capacity Manual

11 Juni 2025
Swingline

Swingline Optima Grip Manual

11 Juni 2025
Swingline

Swingline S7006701 Manual

10 Juni 2025
Swingline

Swingline Optima 20 Manual

10 Juni 2025
Swingline

Swingline Optima 70 Manual

10 Juni 2025
Swingline

Swingline Optima 45 Manual

10 Juni 2025
Novus

Novus J-165 Panel Manual

10 Juni 2025
Novus

Novus J-214 Li-Ion Manual

10 Juni 2025