Metra 70-1780 Manual
Metra
Ikke kategoriseret
70-1780
Læs gratis den danske manual til Metra 70-1780 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Metra 70-1780, eller vil du spørge andre brugere om produktet?
Side 1/2

Receiver Wiring Adaptor
120 70-1780
Revision 01/17/18
STEP 1 -- MATCH & CONNECT WIRES
*120701780*
IMPORTANT
Before starting, compare items on your invoice with items
received. Thoroughly check packing materials. If an item
is missing, please call Crutchfield at 1-888-955-6000.
Copyright 2018 Crutchfield Corporation
Match wires below to the matching function of each wire on your receiver (refer to instructions supplied with receiver). The wire colors of your
new receiver may, or may not, match the wire colors of the adaptor. Match adaptor and receiver wires by function, disregarding color.
Your receiver illumination wire could be Orange or Orange/White. As with other wires, match this wire to the illumination wire in this harness
by function, not by color. If your receiver does not have an illumination wire, tape off the illumination wire.
Individually tape off any unused wires.
Make final wiring connections following instructions on the next page.
A.
B.
C.
D.
Orange - Illumination
Yellow - 12 Volts Constant Power
Red - 12 Volts Switched Power
White - Left Front Speaker Positive
Blue - Antenna/Amplifier Turn-On
Violet - Right Rear Speaker Positive
Green - Left Rear Speaker Positive
Gray - Right Front Speaker Positive Gray/Black - Right Front Speaker Negative
White/Black - Left Front Speaker Negative
Black - Chassis Ground
Violet/Black - Right Rear Speaker Negative
Green/Black - Left Rear Speaker Negative
Justy Vehicles: If not equipped with a factory radio, it may be
necessary to connect the two (2) Blue plugs (located next to the
fuse panel) together in order to have 12 volts constant power at
the Yellow Wire in the plug.

Receiver Wiring Adaptor Connections
120 70-1780
Page 2
STEP 2 -- CONTINUED
A. Strip wires back 1/2”.
B. Twist wires together and
insert in crimp cap.
C. Squeeze middle of cap
for tight connection.
Copyright 2018 Crutchfield Corporation
STEP 3 -- APPLICATION
When ready to install the receiver, plug
the Wiring Adaptor from the new receiver
or receiver assembly into the factory
radio harness(es) in the vehicle dash.
D. Complete crimp connections
for all necessary wires.
E. Be sure to wrap any wires from
the Wiring Adaptor that are
not necessary (wires with no
match from the new receiver)
with electrical tape.
STEP 2 -- CRIMP CONNECTIONS
Tools & Parts
Required
Wire Stripper/Crimp Tool Crimp Caps
Unused Wire (tape over bare wires)
Receiver Wiring Adaptor
Generic Illustration
Generic Illustration
Produkt Specifikationer
Mærke: | Metra |
Kategori: | Ikke kategoriseret |
Model: | 70-1780 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Metra 70-1780 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Metra Manualer
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
21 August 2025
19 August 2025
6 Juli 2025
1 Juli 2025
Ikke kategoriseret Manualer
- Kluge
- EarFun
- PoolSkim
- Tripp Lite
- Aruba
- Brandson
- Mach Power
- Massoth
- Gill
- Playmobil
- HPI Racing
- Global Water
- Imperia
- Roswell
- Metronic
Nyeste Ikke kategoriseret Manualer
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025
22 August 2025