Metra 99-7411 Manual

Metra Ikke kategoriseret 99-7411

Læs gratis den danske manual til Metra 99-7411 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Metra 99-7411, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

99-7411

INSTALLATION

INSTRUCTIONS

APPLICATIONS

CAR PAGE

NISSAN

300ZX 1984-87.......................................................1-2

KIT COMPONENTS

TOOLS REQUIRED

Cutting tool

Wrench

Phillips screwdriver

(4) Phillips Pan-head

Screws

(4) Speed Clips

KIT FEATURES

Shaft and

DIN unit

provisions

Radio Housing

1-800-221-0932 www.metraonline.com

rev. 250701

1 2

3 4

Locate the factory wiring harness in the

dash. Metra recommends using the

proper mating adaptor and making

connections as shown. (Isolate and

individually tape off the ends of any

unused wires to prevent electrical short

circuit).

Re-connect the battery terminal and test the unit

for proper operation. Mount the factory radio

housing to the sub-dash with (4) Phillips screws

previously removed in step #1.

A) Strip wire ends back ½"

B) Twist ends together

C) Solder

D) Tape

Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the

ashtray and (2) screws exposed. Remove (2) screws above the climate controls. Unclip the

radio trim bezel and remove. Remove (4) Phillips screws securing the factory radio housing,

pull the housing assembly out and disconnect the wiring. Remove the screws securing the

factory radio to the factory radio housing and remove.

2-SHAFT HEAD UNITS: Snap the Faceplate onto the the front of the Radio Housing. Mount

the Faceplate/Radio Housing assembly to the factory radio housing with (4) Phillips Pan-

head Screws (4) Speed Clips and supplied. Slide the aftermarket head unit into the kit and

secure with shaft nuts.

DIN HEAD UNITS: Cut and remove the shaft supports from the Faceplate. Snap the

Faceplate onto the front of the Mount the Faceplate/Radio Housing Radio Housing.

assembly to the factory radio housing with (4) Phillips Pan-head Screws and (4) Speed Clips

supplied. Slide the DIN cage into the Housing and secure by bending the metal locking tabs

down. Slide the aftermarket head unit into the cage until secure.

ALL VEHICLES

Factory radio

housing

Radio trim bezel

Produkt Specifikationer

Mærke:	Metra
Kategori:	Ikke kategoriseret
Model:	99-7411

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra 99-7411 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Metra Manualer

Metra 99-8216 Manual

3 Juni 2025

Metra 72-8110 Manual

18 Marts 2025

Metra BLK-9600 Manual

11 Marts 2025

Metra 99-7386B Manual

11 Marts 2025

Metra 82-8602 Manual

13 Januar 2025

Metra 99-8274 Manual

13 Januar 2025

Metra 95-7642 Manual

1 Januar 2025

Metra 95-7022HG Manual

1 Januar 2025

Metra Axxess AXUSB-TY5 Manual

11 December 2024

Metra 71-017C Manual

26 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025