Metra AX-BM9112 Manual

Metra Ikke kategoriseret AX-BM9112

Læs gratis den danske manual til Metra AX-BM9112 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Metra AX-BM9112, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-BM9112

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections to be made .......................................2

Installing the AX-BM9112 .......................................3

Programming the ASWC-1 interface .....................3

Audio level adjustment .........................................4

BMW Mini (R53) (with Harmon Kardon ampliﬁer) 2001-2006

• Provides accessory power

• Retains R.A.P. (retained accessory power)

• Retains audio controls on the steering wheel

• Retains phone buttons (radio dependent)

• Retains factory features: date, time, temperature display

• Selectable audio options

• Micro “B” USB updatable

• AX-BM9112 interface

• ASWC-1 interface

• AX-BM9112 harness

• ASWC-1 harness

• Female 3.5mm connector with stripped leads

CONNECTIONS TO BE MADE

From the aftermarket radio to the AX-BM9112 harness:

• Connect the Black wire to the ground wire.

Note:

There will also be a Black ground wire on the 12-pin pre-wired ASWC-1

harness to connect as well.

• Connect the Yellow wire to the battery wire.

• Connect the Red wire to the accessory wire.

Note:

There will also be a Red accessory wire on the 12-pin pre-wired ASWC-1

harness to connect as well.

• If the aftermarket radio has an illumination wire, connect the Orange wire to it.

• Connect the Blue wire to the antenna turn on wire.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

• Connect the Green wire to the left rear positive speaker output.

• Connect the Green/Black wire to the left rear negative speaker output.

• Connect the Purple wire to the right rear positive speaker output.

• Connect the Purple/Black wire to the right rear negative speaker output.

• The momentary switch will only be used in models that are not equipped with

steering wheel controls.

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls.

• Connect the Black wire to the ground wire.

• Connect the Red wire to the accessory wire.

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to the male

3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard:

• Eclipse: Connect the steering wheel control wire, normally Brown Brown/White, to the wire

of the connector. Then connect the remaining steering wheel control wire, normally Brown/

White, to the Brown wire of the connector.

• Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the wire.Brown

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to

the Brown wire.

• XITE: Connect the steering wheel control SWC-2 wire from the radio to the Brown wire.

• Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio.

Note:

The radio must be updated to rev. 2.1.4 or higher software.

• Universal “2 or 3 wire” radio: Connect the steering wheel control wire, referred to as Key-A or

SWC-1, to the Brown wire of the connector. Then connect the remaining steering wheel control

wire, referred to as Key-B or SWC-2, to the Brown/White wire of the connector. If the radio

comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual provided with

the radio for assigning the SWC buttons. Contact the radio manufacturer for more information

• For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the

aftermarket radio designated for an external steering wheel control interface. Please refer to the

aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

Produkt Specifikationer

Mærke:	Metra
Kategori:	Ikke kategoriseret
Model:	AX-BM9112

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra AX-BM9112 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Metra Manualer

Metra AXHN-2 Manual

19 August 2025

Metra PR-LOC2.4 Manual

6 Juli 2025

Metra 99-8211 Manual

1 Juli 2025

Metra 99-9303 Manual

23 Juni 2025

Metra 98-7599 Manual

19 Juni 2025

Metra 99-6537B Manual

19 Juni 2025

Metra 99-7415 Manual

19 Juni 2025

Metra 99-2002 Manual

19 Juni 2025

Metra 99-3106 Manual

19 Juni 2025

Metra 99-6525HG Manual

19 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Cres Cor H137WSUA5D Manual

20 August 2025

Moulinex Pulseo LM17GD Manual

20 August 2025

Tefal EasyGrill BG1303 Manual

20 August 2025

Tenda U2 Manual

20 August 2025

Tefal Ultraglide Plus FV5841 Manual

20 August 2025

Tefal I-Coach Touch QB950D Manual

20 August 2025

BEKO BDIN38551P Manual

20 August 2025

BEKO FSE52135DCRSN Manual

20 August 2025

Karma PRJ 5000 Manual

20 August 2025

Aqua-Vu Micro Stealth 4.3 Manual

20 August 2025