Metra AX-MC90082 Manual

Metra Ikke kategoriseret AX-MC90082

Læs gratis den danske manual til Metra AX-MC90082 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 110 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 55.5 anmeldelser. Har du et spørgsmål om Metra AX-MC90082, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

CAUTION!

All accessories, switches, climate

controls panels, and especially air bag indicator

lights must be connected before cycling the

ignition. Also, do not remove the factory radio

with the key in the on position, or while the

vehicle is running.

AX-MC90082

I N S TA L L A T I O N I N S T R U C T I O N S

INTERFACE FEATURES

INTERFACE COMPONENTS

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections ............................................................2

Installation .............................................................3

Programming .........................................................3

Mercedes ML (W164) (with M.O.S.T. 25 ampliﬁer)

Data Interface with SWC 2005-2011

Mercedes GL (X164) (with M.O.S.T. 25 ampliﬁer)

Data Interface with SWC 2006-2010

• Provides accessory power

• Retains R.A.P. (retained accessory power)

• Designed for ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains balance

• Micro-B USB updatable

• AX-MC90082 interface

• AX-MC90082 ampliﬁer interface

• ASWC-1 interface

• AX-MC90082 harness

• ASWC-1 harness

• Female 3.5mm connector with stripped leads

CONNECTIONS

From the aftermarket radio to the AX-MC90082 harness:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the accessory wire.Red

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the wire to the amp turn on wire of the new radio. *Blue

* wire triggers the factory antenna booster as well as the ﬁber-optic box.Blue

• Connect the Brown wire to the mute wire.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wire.Light Green

• Tape off and disregard the following (8) wires, they will not be used in this application:

Gray, Gray/Black Green Green/Black Purple Purple/Black White White/Black, , , , , ,

•

Connect the and RCA jacks to the front ampliﬁer output jacks of the aftermarket radio.Red White

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with steering wheel controls.

• Connect the wire to the accessory wire.Red

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to

the

male 3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard

• Connect the steering wheel control wire, normally Eclipse: Brown Brown/, to the

White wire of the connector. Then connect the remaining steering wheel control wire,

normally , to the wire of the connector.Brown/White Brown

• Connect the steering wheel control Key 1 wire (Gray) to the Metra OE: Brown wire.

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow

wire to the wire.Brown

• XITE:

Connect the steering wheel control SWC-2 wire from the radio to the wireBrown

•

Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as

Key-A or SWC-1, to the

Brown

wire of the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the

Brown/White

wire of

the connector. If the radio comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio manufacturer

for more information.

• For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the

aftermarket radio designated for an external steering wheel control interface. Please refer to

the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

Produkt Specifikationer

Mærke:	Metra
Kategori:	Ikke kategoriseret
Model:	AX-MC90082

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra AX-MC90082 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Metra Manualer

Metra PR-LOC2.4 Manual

6 Juli 2025

Metra 99-8211 Manual

1 Juli 2025

Metra 99-9303 Manual

23 Juni 2025

Metra 98-7599 Manual

19 Juni 2025

Metra 99-6537B Manual

19 Juni 2025

Metra 99-7415 Manual

19 Juni 2025

Metra 99-2002 Manual

19 Juni 2025

Metra 99-3106 Manual

19 Juni 2025

Metra 99-6525HG Manual

19 Juni 2025

Metra 99-9225 Manual

19 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Rowenta Thermostyle SF712L Manual

13 August 2025

American Audio CPX 10A Manual

13 August 2025

Bluetti Elite 100 V2 Manual

13 August 2025

American Audio Topaz EX Manual

13 August 2025

American Audio Accu Fog 1000 Manual

13 August 2025

Optimate Solar Duo Manual

13 August 2025

American Audio Micro Wash WWCW Manual

13 August 2025

Adj UC3 Foot Controller Manual

13 August 2025

Adj WiFLY D6 Branch Manual

13 August 2025

Rowenta Magic Nature CF7826 Manual

13 August 2025