Metra AX-PO90052 Manual

Metra Ikke kategoriseret AX-PO90052

Læs gratis den danske manual til Metra AX-PO90052 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 45 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 23 anmeldelser. Har du et spørgsmål om Metra AX-PO90052, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

AX-PO90052

I N S TA L L A T I O N I N S T R U C T I O N S

Product Info

TOOLS REQUIRED

• Wire cutter • Crimp tool • Solder gun • Tape

• Connectors (example: butt-connectors, bell

caps, etc.)

TABLE OF CONTENTS

Connections ............................................................2

Installation .............................................................3

Programming .........................................................3

Porsche (with M.O.S.T. 25 ampliﬁer)

Data Interface with SWC 2004-2009

INTERFACE FEATURES

INTERFACE COMPONENTS

• Provides accessory power

• Retains R.A.P. (retained accessory power)

• Designed for ampliﬁed models

• Provides NAV outputs (parking brake, reverse, speed sense)

• Retains audio controls on the steering wheel

• Retains balance

• Micro-B USB updatable

• AX-PO90052 interface

• AX-PO90052 ampliﬁer interface

• ASWC-1 interface

• AX-PO90052 harness

• ASWC-1 harness

• Female 3.5mm connector with stripped leads

APPLICATIONS

PORSCHE

911 (997) 2004-2009 Boxster (987) 2004-2009 Cayman (987c) 2004-2009

CONNECTIONS

From the aftermarket radio to the AX-PO90052 harness:

• Connect the wire to the ground wire.Black

• Connect the Yellow wire to the battery wire.

• Connect the wire to the accessory wire.Red

• If the aftermarket radio has an illumination wire, connect the wire to it.Orange

• Connect the and the wires to the amp turn-on wire.Blue Blue/White

• If a wire is populated on the factory side, connect the wire with a bullet Blue/White

connector to the amp turn-on wire.

The following (3) wires are only for multimedia/navigation radios that require these wires.

• Connect the wire to the VSS/speed sense wire.Blue/Pink

• Connect the wire to the reverse wire.Green/Purple

• Connect the wire to the parking brake wire.Light Green

• Tape off and disregard the following (8) wires, they will not be used in this application:

Gray, Gray/Black Green Green/Black Purple Purple/Black White White/Black, , , , , ,

• Connect the and RCA jacks to the front ampliﬁer output jacks of the aftermarket radio.Red White

From the aftermarket radio to the ASWC-1 harness:

This harness is only to be used if the vehicle is equipped with

steering wheel controls.

• Connect the wire to the accessory wire.Red

Loose Black/Red wire:

1. Locate pin cavity 1 on the factory harness. If a wire is populated in the

harness, push the wire in the pin cavity and connect this Black/Red

wire to the amp turn-on wire from the aftermarket radio. (Figure A)

• For the radios listed below, connect the

female 3.5mm connector with stripped leads

, to

the

male 3.5mm SWC jack from the ASWC-1 harness. Any remaining wires tape off and disregard

• Connect the steering wheel control wire, normally Eclipse: Brown Brown/, to the

White wire of the connector. Then connect the remaining steering wheel control wire,

normally , to the wire of the connector.Brown/White Brown

• Connect the steering wheel control Key 1 wire (Gray) to the Metra OE: Brown wire.

• Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow

wire to the wire.Brown

• XITE:

Connect the steering wheel control SWC-2 wire from the radio to the wireBrown

•

Parrot Asteroid Smart or Tablet: Connect the 3.5mm jack into the AX-SWC-PARROT (sold

separately), and then connect the 4-pin connector from the AX-SWC-PARROT into the radio

Note:

The radio must be updated to rev. 2.1.4 or higher software.

•

Universal “2 or 3 wire” radio:

Connect the steering wheel control wire, referred to as

Key-A or SWC-1, to the

Brown

wire of the connector. Then connect the remaining

steering wheel control wire, referred to as Key-B or SWC-2, to the

Brown/White

wire of

the connector. If the radio comes with a third wire for ground, disregard this wire.

Note:

After the interface has been programmed to the vehicle, refer to the manual

provided with the radio for assigning the SWC buttons. Contact the radio manufacturer

for more information.

• For all other radios: Connect the 3.5mm jack from the ASWC-1 harness, into the jack on the

aftermarket radio designated for an external steering wheel control interface. Please refer to

the aftermarket radios manual if in doubt as to where the 3.5mm jack goes to.

Wire View

(Figure A)

Produkt Specifikationer

Mærke:	Metra
Kategori:	Ikke kategoriseret
Model:	AX-PO90052

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra AX-PO90052 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Metra Manualer

Metra AXHN-2 Manual

19 August 2025

Metra PR-LOC2.4 Manual

6 Juli 2025

Metra 99-8211 Manual

1 Juli 2025

Metra 99-9303 Manual

23 Juni 2025

Metra 98-7599 Manual

19 Juni 2025

Metra 99-6537B Manual

19 Juni 2025

Metra 99-7415 Manual

19 Juni 2025

Metra 99-2002 Manual

19 Juni 2025

Metra 99-3106 Manual

19 Juni 2025

Metra 99-6525HG Manual

19 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Cres Cor H137WSUA5D Manual

20 August 2025

Moulinex Pulseo LM17GD Manual

20 August 2025

Tefal EasyGrill BG1303 Manual

20 August 2025

Tenda U2 Manual

20 August 2025

Tefal Ultraglide Plus FV5841 Manual

20 August 2025

Tefal I-Coach Touch QB950D Manual

20 August 2025

BEKO BDIN38551P Manual

20 August 2025

BEKO FSE52135DCRSN Manual

20 August 2025

Karma PRJ 5000 Manual

20 August 2025

Aqua-Vu Micro Stealth 4.3 Manual

20 August 2025