Metra NITO-01 Manual

Metra Ikke kategoriseret NITO-01

Læs gratis den danske manual til Metra NITO-01 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Metra NITO-01, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Installation instructions for part NITO-01

REV. 5/17/2017 INSTNITO-01

CAUTION!

All accessories, switches, climate controls panels, and

especially air bag indicator lights must be connected before cycling

the ignition. Also, do not remove the factory radio with the key in the

on position, or while the vehicle is running.

• Provides accessory power (12-volt 10-amp)

• Provides NAV outputs (parking brake,

reverse, and speed sense)

• Pre-wired ASWC-1 harness (ASWC-1 sold

separately)

• Retains the factory backup camera

• Retains the audible parking sensor warning

• Retains the factory AUX-IN jack

• Used in amplified applications

• Adjustable gain control for overall volume

• High level speaker input

• Retains balance

• Micro “B” USB updatable

INTERFACE FEATURES

• Wire cutter • Crimp tool • Solder gun • Tape • Small flat-blade screwdriver

• Connectors (example: butt-connectors, bell caps, etc.)

TOOLS REQUIRED

NITO-01

Nissan Maxima 2016 Amplifier Interface

• NITO-01 interface • NITO-01 harness

• 16-pin harness with stripped leads • AX-CAM6V 12-volt to 6-volt converter

INTERFACE COMPONENTS

Connections to be made ................................................... 2

Installing the NITO-01 ....................................................... 3

Initializing the NITO-01 ..................................................... 3

Adjusting the NITO-01 ...................................................... 3

Extra settings .................................................................... 4

Table of Contents

NITO-01

From the 16-pin harness with stripped leads to the aftermarket radio:

• Connect the Red wire to the accessory wire.

Note: If installing an ASWC-1 (sold separately), there will be an accessory wire

there to connect as well.

• Connect the Blue/White wire to the amp turn on wire. This wire must be

connected to hear sound from the factory amplifier.

•

Tape off and disregard the following (13) wires, they will not be used in this

application: Blue/Pink

Blue/White Brown Gray Gray/Black Green Green/, , , , ,

Black Green/Purple Purple Purple/Black, , ,

, , , Light Green White White/Black

From the NITO-01 harness to the aftermarket radio:

• Connect the Black wire with a ring terminal to chassis ground.

• Connect the Yellow wire to the battery wire.

• Connect the Gray wire to the right front positive speaker output.

• Connect the Gray/Black wire to the right front negative speaker output.

• Connect the White wire to the left front positive speaker output.

• Connect the White/Black wire to the left front negative speaker output.

The following (3) wires are only for multimedia/navigation radios that require these wires

• Connect the Blue/Pink wire to the VSS/speed sense wire.

• Connect the Green/Purple wire to the reverse wire.

Note: Before connecting this wire, also refer to the “AX-CAM6V 12-volt to

6-volt” converter section.

• Connect the Light Green wire to the parking brake wire.

• If retaining the factory AUX-IN jack, connect the & RCA jacks to the Red White

AUX input.

• If retaining the factory backup camera, connect the Yellow RCA jack to the

reverse camera input. Please reference “Reverse camera operation” on page 4

if retaining the camera.

AX-CAM6V 12-volt to 6-volt converter:

• Connect the Black wire to chassis ground.

• Connect the Blue/Red Red wire to the wire labeled “Camera Power 6V”.

• Connect the Blue/White Green/Purple wire to the wire.

Note: The wire will connect to both the AX-CAM6V, and the Green/Purple

aftermarket radio.

12-pin pre-wired ASWC-1 harness:

• This harness is to be used along with the optional ASWC-1 (not included) to

retain steering wheel audio controls. If the ASWC-1 is not being used, disregard

this harness. If it will be used, please refer to the ASWC-1 instructions for radio

connections, and also to the ASWC-1 settings on page 4 of these instructions.

Note: Disregard the harness that comes with the ASWC-1.

• Connect the Red wire to the accessory wire.

Connections to be made

Produkt Specifikationer

Mærke:	Metra
Kategori:	Ikke kategoriseret
Model:	NITO-01

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra NITO-01 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Metra Manualer

Metra 99-8216 Manual

3 Juni 2025

Metra 72-8110 Manual

18 Marts 2025

Metra BLK-9600 Manual

11 Marts 2025

Metra 99-7386B Manual

11 Marts 2025

Metra 82-8602 Manual

13 Januar 2025

Metra 99-8274 Manual

13 Januar 2025

Metra 95-7642 Manual

1 Januar 2025

Metra 95-7022HG Manual

1 Januar 2025

Metra Axxess AXUSB-TY5 Manual

11 December 2024

Metra 71-017C Manual

26 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kora DTR-3342 Manual

16 Juni 2025

Playtive IAN 346914 Manual

16 Juni 2025

Playtive IAN 303641 Manual

16 Juni 2025

Playtive HG05107 Manual

16 Juni 2025

Playtive IAN 346906 Manual

16 Juni 2025

Playtive IAN 285778 Manual

16 Juni 2025

Planet Audio PCBLK3.5 Manual

16 Juni 2025

Sabrent NT-UA25 Manual

16 Juni 2025

ElectriQ STRV-Z1-WH Manual

16 Juni 2025

Watts ETX-30 Manual

16 Juni 2025