Metrix OX 9302 Manual

Metrix Måling OX 9302

Læs gratis den danske manual til Metrix OX 9302 (149 sider) i kategorien Måling. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Metrix OX 9302, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/149
GB
- User’s manual
ScopiX IV
OX 9062
OX 9102
OX 9104
OX 9304
OX9302-BUS
DIGITAL OSCILLOSCOPES
- 60MHz, 2 isolated channels
- 100MHz, 2 isolated channels
- 100MHz, 4 isolated channels
- 300MHz, 4 isolated channels
- 300MHz, 2 isolated channels
2
Thank you for purchasing a ScopiX IV digital oscilloscope with isolated channels.
For best results from your device:
-
Read this user manual attentively,
-
Observe the precautions for its use.
WARNING, risk of DANGER! The operator must
refer to these instructions whenever this danger
symbol appears.
In the European Union, this product is subject to
selective collection and recycling at end-of- life
as waste electric and electronic equipment under
directiv
e 2002/96/EC (WEEE): this equipment
must not be treated as an ordinary household
waste.
Spent batteries must not be treated as
ordinary household waste.
Take them to the
appropriate collection point for recycling.
Indoor use
Instrument entirely protected by double insulation
Earth terminal
Chauvin Arnoux has adopted an Eco-Design
approach in order to design this appliance.
Analysis of the complete lifecycle has enabled us to
control and optimize the effects of the product on
the environment.
In particular this appliance
exceeds regulation requirements with respect to
recycling and reuse.
Risk of electric shocks: instructions for connecting
and disconnecting the inputs.
Always connect the probes or adapters to the
instrument before connecting
them to the
measurement points. Always disconnect the
probes or leads from the measurement points
before disconnecting them from the instrument.
These instructions apply before
cleaning the
instrument and before opening the cover on the
battery compartmen
t and the probe calibration
outputs.
The product is declared recyclable following an
analysis of the life cycle in accordance with
standard ISO 14040.
The CE marking indicates conformity with
European directives, in particular LVD and EMC.
Application or withdrawal not authorized on
conductors carrying dangerous voltages. Type B
current sensor as per EN 61010-2-032.
Definition of measurement categories:
Measurement category IV corresponds to measurements taken at the source of low-voltage installations.
Example: power feeders, counters and protection devices.
Measurement category III corresponds to measurements on building installations.
Example: distribution panel, circuit-breakers, machines or fixed industrial devices.
Measurement category II corresponds to measurements taken on circuits directly connected to low-voltage installations.
Example: power supply to electro-domestic devices and portable tools.
PRECAUTIONS FOR USE
This instrument and its accessories comply with safety standards EN61010-1, EN61010-031, and EN61010-2-032, at voltages
that depend on the accessories (600V CAT III with respect to earth whatever the accessory) at an altitude of less than 2,000m,
indoors, with a degree of pollution ≤2.
Failure to observe the safety instructions may result in electric shock, fire, explosion, and destruction of the instrument and of
the installations.
The operator and/or the responsible authority must carefully read and clearly understand the various precautions to be taken
in use. Sound knowledge and a keen awareness of electrical hazards are essential when using this instrument.
If you use this instrument other than as specified, the protection it provides may be compromised, thereby endangering you.
Do not use your instrument on networks of which the voltage or category exceeds those stated.
Do not use the instrument if it seems to be damaged, incomplete, or poorly close.
Before each use, check the condition of the insulation on the leads, housing, and accessories. Any item of which the
insulation is deteriorated (even partially) must be set aside for repair or scrapping.
Use only the leads and accessories supplied. The use of leads (or accessories) of a lower voltage rating or category limits
the use of the combined instrument + leads (or accessories) to the lowest category and service voltage.
Use personal protection equipment systematically.
When handling the leads, test probes, and crocodile clips, keep your fingers behind the physical guard.
All troubleshooting and metrological checks must be done by competent, accredited personnel.

Produkt Specifikationer

Mærke: Metrix
Kategori: Måling
Model: OX 9302

Har du brug for hjælp?

Hvis du har brug for hjælp til Metrix OX 9302 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Måling Metrix Manualer

Metrix

Metrix AX 501 Manual

7 August 2025
Metrix

Metrix ScopiX IV OX 9302-BUS Manual

7 August 2025
Metrix

Metrix ScopiX IV OX 9304 Manual

7 August 2025
Metrix

Metrix AX 1360P Manual

6 August 2025
Metrix

Metrix MX535 Manual

6 August 2025
Metrix

Metrix OX 9302 Manual

6 August 2025
Metrix

Metrix ScopiX IV OX9062 Manual

29 April 2024

Måling Manualer

Nyeste Måling Manualer

Crowcon

Crowcon Xgard XGB Manual

12 August 2025
Mitsubishi

Mitsubishi SRK10YYPH-W Manual

12 August 2025
Mitsubishi

Mitsubishi SRK18YYPH-W Manual

12 August 2025
Mitsubishi

Mitsubishi SRK24YYMH-W Manual

12 August 2025
PeakTech

PeakTech 8202 Manual

12 August 2025
Mitsubishi

Mitsubishi SRK13YYPH-W Manual

12 August 2025
Mitsubishi

Mitsubishi SRK50ZTLH-WF Manual

12 August 2025
Mitsubishi

Mitsubishi SRK35ZTLH-WF Manual

12 August 2025
Mitsubishi

Mitsubishi SRK25ZTLH-WF Manual

12 August 2025
Mitsubishi

Mitsubishi SRK71ZTLH-WF Manual

12 August 2025