Microchip ATWILC1000-IC Manual

Microchip Ikke kategoriseret ATWILC1000-IC

Læs gratis den danske manual til Microchip ATWILC1000-IC (61 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Microchip ATWILC1000-IC, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/61

Wi-Fi® Link Controller Linux® User Guide

Introduction

This user guide describes how to run Wi-Fi on the ATWILC1000 SD card or the ATWILC3000 Shield board on the

SAMA5D4 Xplained Ultra running with the Linux® kernel 5.4.

Notes: All references to the ATWILC module includes all the devices listed below unless otherwise noted:

• ATWILC1000

• ATWILC3000

The source codes are maintained on GitHub. For latest source codes, see GitHub Linux for ATWILC at github.com/

linux4sam/linux-at91/tree/master/drivers/staging/wilc1000.

Figure 1. ATWILC1000 SD Card and ATWILC3000 Shield Board

Table of Contents

Introduction.....................................................................................................................................................1

1. Prerequisites........................................................................................................................................... 4

2. Building Linux for SAMA5D4 Xplained Ultra Board.................................................................................5

2.1. Cloning a Kernel Source and Root File System...........................................................................5

2.2. Loading SAMA5D4 Configuration File..........................................................................................5

2.3. Buildroot File System and Linux Kernel....................................................................................... 6

2.4. Building Linux Kernel Individually.................................................................................................7

3. Building and Flashing the System Image into the SAMA5D2 Xplained Ultra Board............................... 8

3.1. Build Binaries form Source code..................................................................................................8

3.2. Creating an Image for SAMA5D2_Xplained to Boot using eMMC............................................. 12

3.3. Install the Demo Image on the SAMA5D2 Xplained eMMC.......................................................14

3.4. Initializing the WILC Device........................................................................................................15

4. Building and Flashing the System Image into the SAMA5D3 Xplained Board......................................16

4.1. Download the Demo Package....................................................................................................16

4.2. Building the component..............................................................................................................16

4.3. Flashing the Package to SAMA5D3 Board................................................................................ 17

4.4. Booting the SAMA5D3 Xplained Board......................................................................................18

4.5. Initializing the WILC Device........................................................................................................19

5. Building and Flashing the System Image into the SAMA5D27-SOM1-EK1..........................................20

5.1. Buildroot..................................................................................................................................... 20

5.2. Configuring the Buildroot............................................................................................................21

5.3. Customize Buildroot by Adding Additional Modules...................................................................21

5.4. Building SD Card Image.............................................................................................................25

5.5. Flashing the SD Card Image Using Etcher................................................................................ 25

5.6. Booting Up the Board ................................................................................................................ 27

5.7. Initializing the WILC Device........................................................................................................27

5.8. WILC Support for Desired Kernel Version..................................................................................27

6. Updating Binary and System Image into the Target Board................................................................... 29

7. Updating ATWILC Firmware..................................................................................................................31

7.1. ATWILC1000 and ATWILC3000 Driver Modules........................................................................31

7.2. ATWILC1000 and ATWILC3000 Firmware Binaries...................................................................31

8. Running ATWILC...................................................................................................................................32

8.1. Accessing the Console...............................................................................................................32

8.2. Recognizing ATWILC1000......................................................................................................... 32

8.3. Recognizing ATWILC3000......................................................................................................... 34

8.4. Modifying Configuration Files.....................................................................................................36

8.5. Running in the ATWILC Station Mode........................................................................................38

8.6. Running in the ATWILC AP Mode.............................................................................................. 40

8.7. Running in the ATWILC P2P Mode............................................................................................41

8.8. Supported Modes with Concurrency.......................................................................................... 43