Microchip EVB-USB2507 Manual

Microchip Ikke kategoriseret EVB-USB2507

Læs gratis den danske manual til Microchip EVB-USB2507 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Microchip EVB-USB2507, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

SMSC EVB-USB2507 Revision A1(06-26-07)

The information contained herein is proprietary to SMSC and shall be used solely in accordance with the agreement pursuant to which

it is provided. Although the information is believed to be accurate, no responsibility is assumed for inaccuracies. SMSC reserves the

right to make changes to this document and to specifications and product descriptions at any time without notice. Neither the provision

of this information nor the sale of the described semiconductor devices conveys any licenses under any patent rights or other intellectual

property rights of SMSC or others unless specifically specified otherwise. The product may contain design defects or errors known as

anomalies, including but not necessarily limited to any which may be identified in this document, which may cause the product to deviate

from published specifications. SMSC products are not designed, intended, authorized or warranted for use in any life support or other

application where product failure could cause or contribute to personal injury or severe property damage. Any and all such uses without

prior written approval of an officer of SMSC will be fully at the risk of the customer. SMSC is a registered trademark of Standard

Microsystems Corporation ("SMSC").

SMSC DISCLAIMS AND EXCLUDES ANY AND ALL WARRANTIES, INCLUDING WITHOUT LIMITATION ANY AND ALL IMPLIED

WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, TITLE, AND AGAINST INFRINGEMENT AND THE LIKE,

AND ANY AND ALL WARRANTIES ARISING FROM ANY COURSE OF DEALING OR USAGE OF TRADE. IN NO EVENT SHALL SMSC BE

LIABLE FOR ANY DIRECT, INCIDENTAL, INDIRECT, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES; OR FOR LOST DATA,

PROFITS, SAVINGS OR REV-ENUES OF ANY KIND; REGARDLESS OF THE FORM OF ACTION, WHETHER BASED ON CONTRACT; TORT;

NEGLIGENCE OF SMSC OR OTHERS; STRICT LIABILITY; BREACH OF WARRANTY; OR OTHERWISE; WHETHER OR NOT ANY REMEDY

OF BUYER IS HELD TO HAVE FAILED OF ITS ESSENTIAL PURPOSE, AND WHETHER OR NOT SMSC HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES.

EVB-USB2507 Evaluation Board

Revision A1(06-26-07) SMSC EVB-USB2507

1 Overview

1.1 Features

Operates from a single voltage (+5.0V, regulated) wall wart external power supply

Onboard +3.3V Regulator

Self-powered operation

Serial EEPROM for configuration information mounted in a socket

Header for SMBUS connection

Full set of green and amber LED indicators

Individual port over-current sense and power switching

Multi-TT enabled

High-speed/Full-speed capable

100mS down stream port power on time

1mA VBUS current consumption

1.2 General Description

The primary purpose of this board is to demonstrate a full-featured HUB configuration for the SMSC

USB2507 7-port HUB. This does not represent a minimal cost design. The EEPROM allows for

modifications to the base configuration - for example one or more down stream ports can be disabled

or configured as non-removable for compound device application. The DID, PID or DID information

can be changed for the HUB. The top silk screen of the evaluation board is shown in figure 1.

The EVB-USB2507Q board can be configured via EEPROM or from an external SMBus master. If an

external SMBus master is available it can be connected to header J1. Table 1 shows the jumper

settings to select SMBus or EEPROM. Note that internal default is not supported on this board.

The EVB-USB2507Q can configure the hub to report as self-powered or bus-powered. Table 2shows

the jumper selection.

The board itself does not support true bus power mode. The external power supply must be connected

for the board to operate.

A Windows utility E2PROMAPP is included in the package to allow modifications of the base

configuration EEPROM. The bin file evb-usb2507_01.bin contains the base configuration. A screen

shot from the application is shown in figure 2. After changes has been selected click the button "Create

EEPROM File". Note that if the output file name is put file name it the same as the in will be overwritten

with the new values. The output file name can be changed before creating a new bin file. The bin file

format is compatible with most EEPROM programmers.

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	EVB-USB2507

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip EVB-USB2507 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip AT7913 Manual

1 September 2025

Microchip ATmega1281 Manual

19 Juli 2025

Microchip ATtiny461 Manual

19 Juli 2025

Microchip ATxmega128D3 Manual

19 Juli 2025

Microchip ATxmega128D4 Manual

19 Juli 2025

Microchip ATTINY28 Manual

19 Juli 2025

Microchip ATTINY861 Manual

19 Juli 2025

Microchip ATmega1280 Manual

19 Juli 2025

Microchip ATtiny84A Manual

19 Juli 2025

Microchip ATmega645P Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock PT44 Manual

14 September 2025

BSS Audio FDS-366T Manual

14 September 2025

Systemair Airline R-114 Manual

14 September 2025

IFM SU2031 Manual

14 September 2025

Morel Tempo Ultra Integra 502 Manual

14 September 2025

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025