Microchip MIC5374 Manual


Læs gratis den danske manual til Microchip MIC5374 (23 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Microchip MIC5374, eller vil du spørge andre brugere om produktet?

Side 1/23
MIC5374/84
Triple 200mA µCap LDO and 1mA
RTC LDO in 2.5mm x 2.5mm Thin MLF®
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000http://www.micrel.com
General Description
The MIC5374/84 is a four output device with three 200mA
LDOs and a real time clock (RTC) 1mA LDO which is ideal
for application processor support in mobile platforms. The
MIC5374 provides independent control active high enables
for each of the 200mA LDOs with an additional always-on
RTC LDO. The MIC5384 provides active low enables.
Both the MIC5374 and MIC5384 are available in the tiny
2.5mm x 2.5mm Thin MLF® package.
The MIC5374/84 is designed for high input ripple rejection
(high PSRR) and provides low output noise making it ideal
for powering sensitive RF circuitry such as GPS, WiFi, and
Bluetooth applications. The MIC5374/84 also incorporates
a power-on-reset (POR) supervisor with adjustable delay
time set by an external capacitor, and an independent
input pin to monitor any voltage level. Once high, the POR
output can be asserted low again by enabling the manual
reset (MR) pin. When the MR pin is restored low, the POR
output will re-time the delay set by the external delay
capacitor.
The MIC5374/84 operates with very small ceramic output
capacitors to reduce board space and component cost. It
is available in various fixed output voltages. The
MIC5374/84 has a junction temperature range from 40°C
to 125°C.
Datasheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
Features
1.7V to 5.5V input supply voltage range
Output current - 200mA LDO1/2/3, 1mA LDO4
LDO4 – Ultra low 8µA IBIAS for RTC support
High output accuracy (±2%)
Independent enable pins
POR with user-defined voltage monitoring
POR voltage input
Adjustable delay time
Manual reset pin
Low dropout voltage – 170mV at 150mA
High PSRR 55dB at 1kHz on each LDO
Stable with tiny ceramic output capacitors
2.5mm x 2.5mm Thin MLF 16-pin package
Thermal-shutdown and current-limit protection
Applications
Mobile phones
GPS receivers
Application co-processors
PDAs and handheld devices
Typical Application
Typical MIC5374-xxxYMT Circuit
(Active High Enable)
Typical MIC5384-xxxYMT Circuit
(Active Low Enable)
September 2012 M9999-091712
Micrel, Inc. MIC5374/84
September 2012 2 M9999-091712
Ordering Information
Part Number Mark
Code Output Voltage(1)
Junction
Temperature
Range
Package Lead Finish(2)
MIC5374-MG44YMT MG44 2.8V/1.8V/1.2/1.2V –40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
MIC5374-SJG1YMT SJG1 3.3V/2.5V/1.8V/1.0V –40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
MIC5384-MG44YMT Z1U 2.8V/1.8V/1.2/1.2V –40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
MIC5384-SJG1YMT Z5U 3.3V/2.5V/1.8V/1.0V –40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
Note:
1. Other voltage options available. Contact Micrel for details.
2. Lead finish is NiPdAu. Mold compound material is halogen free.
Pin Configuration
MIC5374
16-Pin 2.5mm x 2.5mm Thin MLF (MT)
(Top View)
MIC5384
16-Pin 2.5mm x 2.5mm Thin MLF (MT)
(Top View)


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC5374

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC5374 stil et spørgsmål nedenfor, og andre brugere vil svare dig