Tripp Lite APS750 Manual

Tripp Lite Batteri APS750

Læs gratis den danske manual til Tripp Lite APS750 (48 sider) i kategorien Batteri. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Tripp Lite APS750, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/48

Owner’s Manual

Quiet Mobile Power

Congratulations! You've purchased the most advanced, feature-rich Inverter/Charger designed as an alternative energy source for residential,

commercial or recreational vehicle applications. Tripp Lite Inverter/Chargers are the quiet alternative to gas generators—with no fumes, fuel or

noise to deal with! You get AC electricity anywhere and anytime you need it: utility power disruptions, rolling down the highway, dry camping in

majestic back country or parked overnight at a money-saving non-electric site. Inverter/Chargers provide your equipment with utility- or

generator-supplied AC electricity (filtered through premium ISOBAR® surge protection) whenever available. In addition, your Inverter/Charger

automatically recharges your connected battery bank. Whenever blackouts, brownouts or high voltages occur, your Inverter/Charger immediately

and automatically switches to battery power.

Safety 2

Feature Identification 3

Operation 4-5

Configuration 5-6

Battery Selection 7

Mounting 8

Battery Connection 9

AC Input/Output Connection 10

Service/Maintenance 10

Troubleshooting 11

Warranty 12

Español 13

Français 25

Русский 37

PowerVerter

DC-to-AC Inverter/Chargers

APSX Models Input Output

Invert: 12 VDC 230V, 50 Hz. AC

Charge: 230V, 50 Hz. AC 12 VDC

APS Models Input Output

Invert: 12 VDC 120V, 60 Hz. AC

Charge: 120V, 60 Hz. AC 12 VDC

WARRANTY REGISTRATION

automatically entered to win an ISOBAR

surge protector in our monthly drawing!

www.tripplite.com/warranty

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

is a registered trademark of Tripp Lite.

Better for

Your Equipment

Premium Protection Levels

• Built-In ISOBAR

Surge Protection

• Automatic Overload Protection

Ideal Output for All Loads

• Frequency-Controlled Output

• Automatic Load Switching

• Balanced Load Sharing

Better for

Your Batteries

Faster Battery Recharge

• High-Amp, 3-Stage Battery Charger

Critical Battery Protection

• High-Efficiency DC-to-AC Inversion

Better for

You

Quiet, Simple, Maintenance-Free

Operation

• Multi-Function Lights & Switches

• Moisture-Resistant Construction*

* Inverter/Chargers are moisture-resistant, not

waterproof.

Important Safety Instructions

SAVE THESE INSTRUCTIONS!

This manual contains important instructions and warnings that should be followed during the installation, operation and storage

of this product.

Location Warnings

• Although your Inverter/Charger is moisture resistant, it is NOT waterproof. Flooding the unit with water will cause it to short circuit and could

cause personal injury due to electric shock. Never immerse the unit, and avoid any area where standing water might accumulate. Mounting

should be in the driest location available.

• Leave a minimum of 2" clearance at front and back of the Inverter/Charger for proper ventilation. To avoid automatic Inverter/Charger

shutdown due to overtemperature, any compartment that contains the Inverter/Charger must be properly ventilated with adequate outside air

flow. The heavier the load of connected equipment, the more heat will be generated by the unit.

• Do not install the Inverter/Charger directly near magnetic storage media, as this may result in data corruption.

• Do not install near flammable materials, fuel or chemicals.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner will seriously inhibit the unit's internal

cooling, eventually causing product damage not covered under warranty.

Battery Connection Warnings

• The battery should be connected before operating the Inverter/Charger

• Multiple battery systems must be comprised of batteries of identical voltage, age, amp-hour capacity and type.

• Because explosive hydrogen gas can accumulate near batteries if they are not kept well ventilated, your batteries should not be installed

(whether for a mobile or stationary application) in a “dead air” compartment. Ideally, any compartment would have some ventilation to

outside air.

• Sparks may result during final battery connection. Always observe proper polarity as batteries are connected.

• Do not allow objects to contact the two DC input terminals. Do not short or bridge these terminals together. Serious personal injury or

property damage could result.

Equipment Connection Warnings

Use of this equipment in life support applications where failure of this equipment can reasonably be expected to cause the failure

of the life support equipment or to significantly affect its safety or effectiveness is not recommended. Do not use this equipment in

the presence of a flammable anesthetic mixture with air, oxygen or nitrous oxide.

• You may experience uneven performance results if you connect a surge suppressor, line conditioner or UPS system to the output of the

Inverter/Charger.

• Corded Models: Do not modify the Inverter/Charger’s plug or receptacle in a way that eliminates its ground connection. Do not use power

adapters that will eliminate the plug’s ground connection.

• Connect your Inverter/Charger only to a properly grounded AC power outlet or hardwired source. Do not plug the unit into itself; this will

damage the device and void your warranty.

• The main grounding lug should be connected to earth ground or to the vehicle chassis with a minimum 8 AWG wire.

Operation Warnings

• Your Inverter/Charger does not require routine maintenance. Do not open the device for any reason. There are no user-serviceable parts

inside.

• Potentially lethal voltages exist within the Inverter/Charger as long as the battery supply and/or AC input are connected. During any service

work, the battery supply and AC input connection (if any) should therefore be disconnected.

• Do not connect or disconnect batteries while the Inverter/Charger is operating in either inverting or charging mode. Operating Mode Switch

should be in the DC OFF position. Dangerous arcing may result.

Caution: These models have a failsafe AC pass-through feature where the AC output will be live (if AC input is available)

even though the operating mode switch is set to “DC OFF.”

Produkt Specifikationer

Mærke:	Tripp Lite
Kategori:	Batteri
Model:	APS750
Bredde:	222.2 mm
Dybde:	228.6 mm
Højde:	177.8 mm
Vægt:	7710 g
Produktfarve:	Sort
Pakkevægt:	8890 g
Pakkedybde:	269.2 mm
Pakkebredde:	269.2 mm
Pakkehøjde:	315 mm
Dimensioner (BxDxH):	222.3 x 228.6 x 177.8 mm
Udgangseffekt:	750 W
Udgangsspænding:	12 V
Harmoniseret systemkode (HS):	8504.40.9570
Indgangsspænding:	120 V
Hovedkassen højde (udvendigt):	315 mm
Hovedkassens længde (udvendigt):	269.2 mm
Hovedkassens bruttovægt (udvendigt):	8890 g
Hovedkassens bredde (udvendigt):	269.2 mm
Oprindelsesland:	Kina
Produkter pr. hovedkasse (udvendigt):	1 stk
Indgangsfrekvens:	60 Hz
Beskyttelse mod overspænding:	Ja