Microchip SY84113BU Manual


Læs gratis den danske manual til Microchip SY84113BU (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 5 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 3 anmeldelser. Har du et spørgsmål om Microchip SY84113BU, eller vil du spørge andre brugere om produktet?

Side 1/10
SFP Module Reference Design
SFP_SY84782U_R0
Preliminary
Micrel Inc. • 2180 Fortune Drive Jose, CA 95131 • USA • tel +1 (408) 944 0800 • fax + 1 (408) 474 1000 • San - - http://www.micrel.com
March 19, 2015
Preliminary
General Description
This evaluation board is a complete SFP module as
dened in the SFP MSA document. The design uses
Micrel’s MIC3003 controller, the 1 G DFB/FP laser .25
driver SY84782U, and any of the SY84113U iting lim
amplier A picture of the fully loaded board is shown on .
the next page.
Datasheets and support documentation are available on
Micrel’s web site at: . www.micrel.com
Related Support Documentation
MIC3003 datasheet: Fibre optic module controller
featuring digital diagnostic monitoring interface, as per
SFF-8472/SFF-8432, with internal/external calibration
and full laser control with bias and modulation current
compensation for temperature variations using lookup
tables.
84782U datasheet. SY .
SY84113U datasheet. . .
MIC3003 software user’s guide.
Features
Compliant with SFP MSA
Allows for easy and fast evaluation of Micrel’s chipset
for low power SFP module
Multi-rate operation up to 1.25Gbps
Single, power supply: 2.5V or 3.3V
Extended temperature range: -40°C to +9 5°C
Transmitter FP/DFP Laser Diode Driver
Operates from a single 2.5V or 3.3V supply
Modulation current up to 80mA
C be DC or AC coupled to the laser an
Small form factor 3mm x 3mm QFN package
Receiver Limiting Post Amplier
Wide dierential input range (5mVPP 1800to mVPP)
Wide SD de-assert or LOS assert threshold range
3mVPP to 30mVPP with 4dB typical electrical hysteresis
Fast SD / LOS assert/de-assert time
Available in a tiny 3mm x 3mm QFN package
Controller
Extensive temperature range
Alarms and warnings interrupt and TXFAULT masks
Capability to support up to four chips on the serial
interface
Integrated digital temperature sensor
Temperature compensation of modulation, bias, and
fault levels via NVRAM lookup tables
User-writeable EEPROM scratchpad
Option to be used with Cisco security chip
Diagnostic monitoring interface per SFF-8472/8432
Space saving 3mmx3mm package available
(MIC3003GFL)
Micrel, Inc.
March , 2015 17
2
Preliminary
Evaluation Board
TOSA
SY84113U ROSA
Top Side
MIC3003 Boom Side
SY84782U
Evaluation Board Setup
TOSA and ROSA Installation
Check the pin conguration of the TOSA and ROSA and
install them according to the diagrams shown in Figure 1.
Driver Laser Coupling
The laser is AC-coupled to the driver. Compensation for
laser parasitics can be improved by choosing appropriate
values for R6 and C15 (or R6 and C7) T. he laser’s
response can be improved by tuning, in addition to
R6/C15, R2 and R4/R13/L3. The optimal values of /R3/L2
these components depend on the length of the laser leads
and can vary from one family of lasers to another. It’s up to
the user to tune the values in order to achieve the best
compensation for the laser used with this board.
Receiver Sensitivity and Hysteresis Setting
The limiting amplier has a receive signal LOS/SD
indicator. The LOS/SD sensitivity is set by the voltage at
SD/LOSLVL (pin ) adjusted by the value of R , which 14 16
forms a voltage divider with the 2.8k internal resistor
terminated to VCC-1.3V.
TOSA Anode (Top)
TOSA PD Anode (Top)
TOSA Cathode (Top)
ROSA VOUT+ (Top)
ROSA GND (Top)
ROSA VOUT- (Top)
TOSA GND (Bottom)
ROSA RSSI (Bottom)
ROSA VDD (Bottom)
Figure 1 Mounting of TOSA and ROSA .


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: SY84113BU

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip SY84113BU stil et spørgsmål nedenfor, og andre brugere vil svare dig