Milwaukee V28 Manual

Milwaukee Lommelygter V28

Læs gratis den danske manual til Milwaukee V28 (4 sider) i kategorien Lommelygter. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Milwaukee V28, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
WORK LIGHT
Compatible with MILWAUKEE V28 Lithium-Ion Battery Packs
LAMPE DE TRAVAIL
Compatible avec batterie
Lithium-Ion
V28
MILWAUKEE
LAMPARA DE TRABAJO
Compatible con baterías Iones de Litio de de V28 MILWAUKEE
Cat. No.
No de Cat.
49-24-0185
OPERATOR'S MANUAL
MANUEL de L'UTILISATEUR
MANUAL del OPERADOR
TO REDUCE THE RISK OF INJURY, USER MUST READ OPERATOR'S MANUAL.
AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE LE
MANUEL DE L'UTILISATEUR.
PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER EL MANUAL
DEL OPERADOR.
2 3
ASSEMBLY
Replacing the Bulb
1. Remove battery pack before changing
bulb.
2. Unscrew the bezel assembly on pivot
head by turning counterclockwise.
3. Remove the bezel assembly.
4. Pull forward the aluminum heat sink.
5. Gently rotate the bulb counter
clockwise and pull out.
To reduce the risk of injury, DO
NOT operate work light without
bezel assembly in place. Bulb does
get hot. Always remove battery
pack before changing or removing
bulbs. Always allow the work light
to cool for at least 10 minutes
before replacing the bulb.
Fig. 2
Bezel
assembly
Spare bulb storage
Bulb
Aluminum
heat sink
Pivot
head
To install new bulb, follow above
directions in reverse.
NOTE: Use a soft cloth when installing bulbs.
Direct contact with oils or other contamina-
tion can shorten the life of bulbs.
F o r wo rk l ig ht 4 9- 2 4 - 01 8 5 , us e
replacement bulb 49-81-0040.
A spare bulb is provided with the work
light. The bulb is located behind the
aluminum heat sink.
See your nearest MILWAUKEE Retailer
or Service Center to obtain replacement
bulbs.
To reduce the risk of injury, do not
look directly into the light when the
work light is on.
Adjusting the Pivot Head
The pivot head can pivot to a range of 140°;
110° up and 30° down with detents every
10°. Pivot head to desired position (Fig. 1).
Allow the detent to snap into place. Do not
forcibly pivot the head.
Fig. 1
Removing Battery Pack from Tool
Push in the release buttons and pull the
battery pack away from the tool.
Inserting Battery Pack into Tool
To insert the battery pack onto the tool, slide
the pack onto the body of the tool. Make sure
it latches securely into place.
To reduce the risk of injury and
damage, never insert bulbs other
than MILWAUKEE 28V bulbs in the
bulb socket. Other bulbs will over
heat!
Intelligent Circuit
This work light is equipped with an
intelligent circuit. If an improper voltage
bulb is installed, the light will flash
repeatedly. If this occurs, remove the
improper bulb and install a MILWAUKEE
28V bulb.
• Read all the instructions before using
the appliance.
• To reduce the risk of injury, close super-
vision is necessary when an appliance is
used near children.
• Do not use outdoors.
• For a rechargeable appliance - Use only
the charger supplied by the manufacturer
to recharge.
• For an appliance with a replaceable
lamp - always unplug before replacing the
lamp. See "Specifi cations" for replacement
bulbs.
• Know your work light. Read this manual
carefully to learn your work light's applica-
tions and limitations as well as potential
hazards associated with this type of tool.
• Batteries must be recharged only with
the specifi ed charger for the battery. A
charger that may be suitable for one type
of battery may create a risk of fi re when
used with another battery.
• Use work light only with specifi cally
designated battery pack. Use of any
other batteries may create a risk of fi re.
READ AND UNDERSTAND ALL INSTRUCTIONS.
When using electric appliances, basic precautions should always be followed,
including the following:
WARNING
IMPORTANT SAFETY INSTRUCTIONS
• When battery pack is not in use, keep
it away from metal objects like: paper
clips, coins, keys, nails, screws, or
other small metal objects that can
make a connection from one terminal
to another. Shorting the battery terminals
together may cause sparks, burns, or a
fi re.
• N ev er in se rt bu lb s oth er th an
MILWAUKEE bulbs in the bulb socket.
Bulbs other than MILWAUKEE bulbs
may cause short circuit of battery and
personal injury.
• Store idle work light out of reach
of children. Warm work lights can
become hazardous in the hands of chil-
dren.
• Maintain labels and nameplates.
These carry important information.
If unreadable or missing, contact a
MILWAUKEE service facility for a free
replacement.
Volts DC
28
Cat. No.
49-24-0185
Specifi cations
Volts Direct Current
Symbology
Underwriters Laboratories, Inc.
Before using the work light, read this operator's manual, your battery pack and charger
operator's manual, and all labels on the battery pack, charger and work light.
SAVE THESE
INSTRUCTIONS
Replacement Bulbs
49-81-0040
WARNING
WARNING WARNING

Produkt Specifikationer

Mærke: Milwaukee
Kategori: Lommelygter
Model: V28

Har du brug for hjælp?

Hvis du har brug for hjælp til Milwaukee V28 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lommelygter Milwaukee Manualer

Milwaukee

Milwaukee V28 Manual

6 Oktober 2024

Lommelygter Manualer

Nyeste Lommelygter Manualer

Nitecore

Nitecore MH41 Manual

14 Januar 2025
Fenix

Fenix LD41 Manual

14 Januar 2025
Nitecore

Nitecore EC25 Manual

14 Januar 2025
Nitecore

Nitecore MT26 Manual

13 Januar 2025
Nitecore

Nitecore EC11 Manual

14 Oktober 2024
Makita

Makita ML185 Manual

13 Oktober 2024
Nitecore

Nitecore MT40GT Manual

13 Oktober 2024
Nitecore

Nitecore MH25GT Manual

12 Oktober 2024
Nitecore

Nitecore MH27UV Manual

12 Oktober 2024
Olight

Olight i3S EOS Manual

12 Oktober 2024