Mitsubishi WL6700U Manual

Mitsubishi Projektorer WL6700U

Læs gratis den danske manual til Mitsubishi WL6700U (8 sider) i kategorien Projektorer. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Mitsubishi WL6700U, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
1
LCD Projector
WL6700U
Controlling the projector using a personal computer
This projector can be controlled by connecting a personal computer with RS-232C terminal.
PC-controllable functions:
• Turning the power ON or OFF
• Changing input signals
• Inputting commands by pressing the buttons on the control panel and remote control
• Menu setting
Connection
RS-232C cable SERIAL
D-SUB 9-pin D-SUB 9-pin
To RS-232C
terminal
Important:
• Connect the computer with the projector on a one-to-one basis.
• Make sure that your computer and projector are turned off before connection.
• Boot up the computer fi rst, and then plug the power cord of the projector.
(If you do not follow this instruction, the Com port may not function.)
• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.
1. Interface
1.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)
Pin No. Name I/O
1 OPEN
2 RXD IN
3 TXD OUT
4 OPEN
5 GND
6 OPEN
7 OPEN
8 OPEN
9 OPEN
1.2 Communications format
PROTOCOL RS-232C
BAUD RATE 9600 [bps]
DATA LENGTH 8 [bits]
PARITY BIT NONE
STOP BIT 1 [bit]
FLOW CONTROL NONE
This projector uses RXD, TXD and GND lines for RS-232C control.
For RS-232C cable, the reverse type cable should be used.
2
2. Control command diagram
The command consists of the address code, function code, data code, and end code. The length of the command
varies among the functions.
Address code Function code Data code End code
ASCII ‘30h’ 30h’ Function Data ‘0Dh’
Character 00 Function Data
[Address code] 00 (In ASCII code, ‘30h’ ‘30h’) fi xed.
[Function code] A code of each fi xed control move.
[Data code] A code of each fi xed control data (number) and not always indicated.
[End code] (In ASCII code, ‘0Dh’) fi xed.
3. Control sequence
Computer Projecto
r
1
2
3
4
Sequence Note
1Send the command from the
personal computer to the projector.
2
The projector will send a return
command after it receives an end
code.
If the projector does not receive commands
normally, that is, if the projector is not connected
physically or unable to receive commands, it does
not send out a return command.
The projector sends out a return command within
one second at the latest.
3
The personal computer checks the
command and confi rms if the sent
command has been received or not.
Although the projector receives the commands, it
in some cases does not execute the commands.
4
Use the check command to see
if the projector has executed the
command.
This projector sends various codes other than the
return code. When having a control sequence by
RS-232C, reject other codes from the personal
computer.
• Although the projector sends out the return command, the command may not take effect in the following
cases.
(1) During signal switching
(2) In the process of the auto position
(3) After the power is turned on.
The projector receives no commands for about 20 seconds (or for 2 minutes at the longest if the lamp
does not light up promptly as the life is expiring.)
• When sending commands successively, wait to receive the return command of the current command before
sending a next command.
• The projector may not receive a command when the splash screen is being displayed immediately after turn-
ing on the power. Use command “00r10” to cancel the splash screen.
• While using the LAN terminals, the LAN functions take precedence.
• For the LAN terminals, the same commands as those for connecting with the TCP/IP (port number 63007) are
available. Note, however, that the response becomes slightly slower than when using the RS-232C terminals.
[Example] When turning the power ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):
Sending commands
from the PC, etc.
Status code
from the projector Description
‘30’ ‘30’ ‘21’ ‘0D’
00!
Command for POWER ON
‘30’ ‘30’ ‘21’ ‘0D’
00!
Command receipt confi rmation
(Command echo back)
• The fl owchart on the next page shows the recommended operating sequence for your reference to create a
program.

Produkt Specifikationer

Mærke: Mitsubishi
Kategori: Projektorer
Model: WL6700U

Har du brug for hjælp?

Hvis du har brug for hjælp til Mitsubishi WL6700U stil et spørgsmål nedenfor, og andre brugere vil svare dig


Projektorer Mitsubishi Manualer

Mitsubishi

Mitsubishi WL6700U Manual

11 Juli 2024
Mitsubishi

Mitsubishi WD8200U Manual

10 Juli 2024
Mitsubishi

Mitsubishi XD3500U Manual

9 Juli 2024
Mitsubishi

Mitsubishi WD570U Manual

8 Juli 2024

Projektorer Manualer

Nyeste Projektorer Manualer

Barco

Barco Data 708 Manual

14 Januar 2025
Hitachi

Hitachi CP-X970W Manual

13 Januar 2025
Hitachi

Hitachi CPX327W Manual

12 Januar 2025
Dell

Dell 1420X Manual

15 Oktober 2024
Sanyo

Sanyo PLC-WXU10B Manual

15 Oktober 2024
Hitachi

Hitachi CPX385W Manual

14 Oktober 2024
Hitachi

Hitachi CP-S860E Manual

13 Oktober 2024
BenQ

BenQ MS506 Manual

12 Oktober 2024
BenQ

BenQ LW21 Manual

12 Oktober 2024
InFocus

InFocus LP330 Manual

12 Oktober 2024