Mitsubishi XL6600U Manual

Mitsubishi Beamer XL6600U

Læs gratis den danske manual til Mitsubishi XL6600U (8 sider) i kategorien Beamer. Denne vejledning er vurderet som hjælpsom af 57 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 29 anmeldelser. Har du et spørgsmål om Mitsubishi XL6600U, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

LCD Projector

XL6600U/XL6500U

Controlling the projector using a personal computer

This projector can be controlled by connecting a personal computer with RS-232C terminal.

PC-controllable functions:

• Turning the power ON or OFF

• Changing input signals

• Inputting commands by pressing the buttons on the control panel and remote control

• Menu setting

Connection

RS-232C cable SERIAL

D-SUB 9-pin D-SUB 9-pin

To RS-232C

terminal

Important:

• Connect the computer with the projector on a one-to-one basis.

• Make sure that your computer and projector are turned off before connection.

• Boot up the computer ﬁ rst, and then plug the power cord of the projector.

(If you do not follow this instruction, the Com port may not function.)

• Adapters may be necessary depending on the PC connected to this projector. Contact your dealer for details.

1. Interface

1.1 Pin assignment of SERIAL terminal (D-SUB 9-pin)

Pin No. Name I/O

1 OPEN

2 RXD IN

3 TXD OUT

4 OPEN

5 GND

6 OPEN

7 OPEN

8 OPEN

9 OPEN

1.2 Communications format

PROTOCOL RS-232C

BAUD RATE 9600 [bps]

DATA LENGTH 8 [bits]

PARITY BIT NONE

STOP BIT 1 [bit]

FLOW CONTROL NONE

This projector uses RXD, TXD and GND lines for RS-232C control.

For RS-232C cable, the reverse type cable should be used.

2. Control command diagram

The command consists of the address code, function code, data code, and end code. The length of the command

varies among the functions.

Address code Function code Data code End code

ASCII ‘30h’ 30h’ Function Data ‘0Dh’

Character 00 Function Data

[Address code] 00 (In ASCII code, ‘30h’ ‘30h’) ﬁ xed.

[Function code] A code of each ﬁ xed control move.

[Data code] A code of each ﬁ xed control data (number) and not always indicated.

[End code] (In ASCII code, ‘0Dh’) ﬁ xed.

3. Control sequence

Computer Projecto

Sequence Note

1Send the command from the

personal computer to the projector.

The projector will send a return

command after it receives an end

code.

If the projector does not receive commands

normally, that is, if the projector is not connected

physically or unable to receive commands, it does

not send out a return command.

The projector sends out a return command within

one second at the latest.

The personal computer checks the

command and conﬁ rms if the sent

command has been received or not.

Although the projector receives the commands, it

in some cases does not execute the commands.

Use the check command to see

if the projector has executed the

command.

This projector sends various codes other than the

return code. When having a control sequence by

RS-232C, reject other codes from the personal

computer.

• Although the projector sends out the return command, the command may not take effect in the following

cases.

(1) During signal switching

(2) In the process of the auto position

(3) After the power is turned on.

The projector receives no commands for about 20 seconds (or for 2 minutes at the longest if the lamp

does not light up promptly as the life is expiring.)

• When sending commands successively, wait to receive the return command of the current command before

sending a next command.

• The projector may not receive a command when the splash screen is being displayed immediately after turn-

ing on the power. Use command “00r10” to cancel the splash screen.

• While using the LAN terminals, the LAN functions take precedence.

• For the LAN terminals, the same commands as those for connecting with the TCP/IP (port number 63007) are

available. Note, however, that the response becomes slightly slower than when using the RS-232C terminals.

[Example] When turning the power ON. (Figures and symbols enclosed in quotation marks are ASCII codes.):

Sending commands

from the PC, etc.

Status code

from the projector Description

‘30’ ‘30’ ‘21’ ‘0D’

00!

Command for POWER ON

‘30’ ‘30’ ‘21’ ‘0D’

00!

Command receipt conﬁ rmation

(Command echo back)

• The ﬂ owchart on the next page shows the recommended operating sequence for your reference to create a

program.

Produkt Specifikationer

Mærke:	Mitsubishi
Kategori:	Beamer
Model:	XL6600U

Har du brug for hjælp?

Hvis du har brug for hjælp til Mitsubishi XL6600U stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Beamer Mitsubishi Manualer

Mitsubishi XD435U-G Manual

4 Oktober 2024

Mitsubishi XD470U Manual

23 September 2024

Mitsubishi XL6600U Manual

19 September 2024

Mitsubishi XL4U Manual

15 September 2024

Mitsubishi HC7000 Manual

16 August 2024

Mitsubishi PK20 Manual

12 August 2024

Mitsubishi SD510U Manual

5 August 2024

Mitsubishi EX240U Manual

5 August 2024

Mitsubishi EW331U-ST Manual

4 August 2024

Mitsubishi EW230U-ST Manual

4 August 2024

Beamer Manualer

Nyeste Beamer Manualer

Hisense 100L5ND Manual

2 April 2025

Philips NeoPix 130 Smart Manual

5 Marts 2025

Philips NeoPix 200 NPX200 Manual

5 Marts 2025

Sharp XP-P601Q Manual

20 Februar 2025

InFocus Genesis IN0026ST Manual

20 Februar 2025

20 Februar 2025

30 Januar 2025

30 Januar 2025

30 Januar 2025

Acer Vero PL3515ATV Manual

30 Januar 2025