Mobotix M26 Allround Manual

Mobotix Overvågningskamera M26 Allround

Læs gratis den danske manual til Mobotix M26 Allround (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Mobotix M26 Allround, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

M26 Allround

Quick Install

32.818-003_EN_04/2018

Standard Delivery M26

1.2

1.3

1.9

1.10, 1.11, 1.12

1.14

1.8

1.13

1.5

1.4

1.6

1.1

1.15

Item Count Part Name

1.1 1 Camera in weatherproof housing, incl. VarioFlex wall mount

1.2 1 Ceiling mount

1.3 1 Sealing for wall and ceiling mount

1.4 1 Lens, installed (standard M14 or B016)

1.5 2 Lens cover, 1 installed, 1 replacement (not available for lens

B016, cover for B500 not shown, no replacement cover for B500)

1.6 1 Lens wrench B016 (only for D016/N016)

1.7 2 Allen wrench 5 mm, Allen wrench 2.5 mm

1.8 1 Special Ethernet cable 0.5 m/20", installed

1.9 4 Screw caps for stainless steel fastening screws

1.10 4 Stainless steel wood screws 6x50 mm

1.11 4 Stainless steel washers 6.4 mm dia.

1.12 4 Dowel S8

1.13 2

Cable lock with bayonet catch (Ethernet patch cable, MiniUSB)

1.14 1 MicroSD card installed

1.15 1 MiniUSB plug

Removing/Installing the Weatherproof Housing

For certain tasks (e.g., connecting additional wires, exchanging the SD card), you need to remove the weatherproof housing and install it again once you

are nished.

1. Remove the fastening screws at the back

Start by removing the two rubber plugs that

protect the fastening screws. Next, unscrew

the two fastening screws of the weatherproof

housing using the supplied Allen wrench 5 mm

(item 1.7), but do not remove the screws

2. Remove camera from weatherproof hous-

ing

Press the camera from the housing by gently

applying pressure on the screws in alternating

fashion from the rear using the long shank of

the Allen wrench. Unscrew the fastening screws

once the camera is free from the housing

3. Complete the tasks

Follow the procedures for the work inside the

housing as described in the M25 Camera Manual

in Chapter 2, «Installation» (e.g., connecting

additional wires, exchanging the SD card).

4. Insert the camera into the weatherproof housing

Start by inserting the camera into the weath-

erproof housing. Press the camera back into

the housing and take care not to squeeze and

damage any wires inside the housing.

5. Tighten the retaining screws

Aix the camera in the weatherproof housing

using the two retaining screws.

Finally, push in the two rubber plugs that

protect the retaining screws.

Mounting Options of the M26

1. Mounting to a Wall

When installing the M26 on a wall, for example, simply aix the pre-installed

and VarioFlex wall mount included in the delivery with the four supplied

screws and washers.

The camera can be turned or tilted 180° horizontally and 110° vertically

(from –90° to +20°).

2. Mounting to a Ceiling

By exchanging the wall mount for the separately supplied ceiling mount,

the M26 is ready to be mounted to ceilings in just a few easy steps thanks

to the VarioFlex system.

The camera can be turned or tilted 360° horizontally and 110° vertically

(from –90° to +20°).

3. Mounting to Poles (With Accessories)

If you want to mount the camera to a pole with a diameter from 60 to 180 mm,

you should consider using the Pole Mount (MX-MH-SecureFlex-ESWS) made

from white powder-coated stainless steel.

Just like when mounting to a wall, the camera can be turned 180° hor-

izontally and tilted 110° vertically (from –90° to +20°).

Connection and Initial Operation of the M26

For information on connecting the M26, please see the M25 Camera Manual, section «Network and Power Connection, Additional Cables» (PDF, available

on www.mobotix.com > Support > Download Center > Documentation > Manuals).

Please note that the boot options of this camera have changed compared to its predecessor (see «Boot Options of the M26» on page 2) and the camera

only has one key ("R"). Regarding the rest of the initial operation of the M26 please see the M25 Camera Manual in Chapter 3, «Initial Operation»

Microphone

Wall Mount

Recording

Weatherproof

housing

Lens and lens

cover

Speaker

Power/Status

Key R

Ethernet

Pressure vent

MxBus

Retaining screws

USB

Rear (without weatherproof housing)

Installing the M26

1. Drill the holes for the dowels (if required)

Use the drilling template for this step (see

below). Mark the holes for dowels or screws

(blue circles in gure). If required, drill the holes

for the dowels, push them in and cut the cut-

out for the cables. Guide the Ethernet cable

and any other cables that are to be connected

through the cut-out.

2. Connect the cables

If you want to connect additional cables

(USB, MxBus), remove the weatherproof

housing as shown in Section «Removing/

Installing the Weatherproof Housing», con-

nect the cabling as required and again install

the housing. Plug the pre-installed Ether-

net cable into a network socket (e.g., of an

MX-Overvoltage-Protection-Box).

3. Install the camera

Press the wall/ceiling mount and the wall sealing against the mounting

position and align the holes with the holes for the dowels/screws. Insert

the screws with washers and tighten them using a torque of 0.4 Nm. Finally,

press the white covers onto the screw heads.

Inserting/Exchanging the SD Card

All camera models can use the integrated MicroSD card (SDHC) to record video data. In order to exchange the MicroSD card, please proceed as outlined

in the following instruction. For information on reliable SD cards, please see the MOBOTIX website www.mobotix.com > Support > Download Center >

Documentation > White Lists in the document MicroSD Card Whitelist for MOBOTIX Cameras.

When replacing the SD card, make sure that recording has been deactivated in the browser (Admin Menu > Storage > Storage on External File Server /

Flash Device; activate recording again in the same dialog aer exchanging the card).

1. Remove the SD Card

Open the camera (see «Removing/Installing the Weath-

erproof Housing» ), remove all connectors in the cover

of the inner housing, then remove the cover. Remove

the four screws from the back plate and li o the

back plate. Gently push on the MicroSD card in the

card slot of the camera. The card is released from the

slot and can be removed from the camera.

2. Insert the SD Card

Push the MicroSD card into the card slot as shown,

until an audible and perceptible click indicates it is in

place

. Replace the back plate of the camera housing.

Variants

Mx-M26A/B*

B036 – B500

Mx-M26A/B*

B016

*Variant Mx-M26B supports MOBOTIX MxBus modules

Produkt Specifikationer

Mærke:	Mobotix
Kategori:	Overvågningskamera
Model:	M26 Allround
Kode for international beskyttelse (IP):	IP66
Type:	IP-sikkerhedskamera
Bredde:	140 mm
Dybde:	220 mm
Højde:	189 mm
Vægt:	350 g
Produktfarve:	Hvid
Kompatible hukommelseskort:	MicroSD (TransFlash)
Wi-Fi:	Ingen
Bluetooth:	Ingen
USB-port:	Ja
Formfaktor:	Kasse
Indbyggede højttaler(e):	Ja
Ethernet LAN:	Ja
Strømforbrug (typisk):	5 W
Driftstemperatur (T-T):	-40 - 50 °C
Maksimal opløsning:	3072 x 2048 pixel
Understøttede grafikopløsninger:	1280 x 720 (HD 720),1280 x 960,1920 x 1080 (HD 1080),2048 x 1536 (QXGA),2592 x 1944,3072 x 2048
Forbindelsesteknologi:	Ledningsført
Certificering:	EN55032: 2012; EN55022: 2010; EN55024: 2010; EN50121-4: 2015; EN61000-6-1: 2007; EN 61000-6-2: 2005; EN61000-6-3: 2007 + A1: 2011; EN61000-6-4: 2007 + A1: 2011; AS / NZS CISPR22: 2009 + A1: 2010; CFR47 FCC 15B
Kabelteknologi:	10/100Base-T(X)
Netværksstandarder:	IEEE 802.3af
Understøttede netværksprotokoller:	IPv4, IPv6, HTTP, HTTPS, FTP, FTPS, RTP, RTSP, UDP, SNMP, SMTP, DHCP, NTP, SIP
Webbaseret administration:	Ja
LED-indikatorer:	Status
Strømkilde type:	PoE
Monteringstype:	Væg
Indbygget kortlæser:	Ja
Indbygget HDD:	Ingen
Video komprimeringsformater:	H.264, M-JPEG, MxPEG
Harmoniseret systemkode (HS):	85258900
Understøttet placering:	Indendørs & udendørs
Indbygget mikrofon:	Ja
Sensortype:	CMOS
Samlet antal megapixels:	6 MP
Digital zoom:	8 x
Grænseflade:	RJ-45
Progressiv scanning:	Ja
Voice codecs:	G.711, G.722
IK kode:	IK10
Minimumsbelysning:	0.001 Lux
Antal sensorer:	1
Optisk sensorstørrelse:	1/1.8 "
Zoom kapacitet:	Ja
Maksimale blænderåbning tal:	1.8
Fast brændvidde:	6.1 mm
Ethernet-grænsefladetype:	Hurtigt ethernet
Antal kameraer:	1
Videostreaming:	Ja
Antal linser:	1
Streaming metode:	Multicast
PTZ-kontrol:	Ja
Temperaturføler:	Ja
Prøvetagningshastighed:	16 kHz
Objektivets synsvinkel, vandret:	60 °
Objektivets synsvinkel, lodret:	45 °