Mobotix MX-D16A-F-6D6N061 Manual

Mobotix Overvågningskamera MX-D16A-F-6D6N061

Læs gratis den danske manual til Mobotix MX-D16A-F-6D6N061 (2 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Mobotix MX-D16A-F-6D6N061, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Mx-D16

32.803-005_EN_10/2017

Quick Install

D16 DualDome

Variants

D16

• Mx6 system platform, H.264 support

• Recording on internal MicroSD card (SDXC, SDHC installed)

• Audio integrated (microphone and speaker)

• Sensor for temperature and shock detector(*) integrated

• PIR detector integrated

• Can be extended exibly using sets for outdoor applications

• Easy installation at building corners and poles using the

Corner and Pole Mount (accessory)

• Use the Vandalism Set for surveillance at extremely critical locations

• Weatherproof and robust camera housing (IP54, IK10)

Standard Delivery D16

1.9

1.6

1.5

1.3

1.4

1.10

1.11

1.12

1.13

1.1

1.2b

1.2a

1.2c

1.8

1.15

1.14

1.7

Item Count Part Name

1.1 1

Camera housing

1.2a 1

Lens units with lenses (freely adjustable,

to be ordered

separately

)

1.2b 1

Pano lens bridge (for 180° Panorama,

to be ordered

separately

, pre-installed)

1.2c 1

Fix lens bridge (for one day and one night lens,

to be

ordered separately

, pre-installed)

1.3 1

Standard dome for D16 Body

1.4 1

Enlarged XL dome for D16 complete cameras (Pano and

Fix) and part of the delivery of the Pano/Fix lens bridges

1.5 1

Cable cover

1.6 1

Ethernet cable

1.7 1

Hinged ferrite

1.8 1

MicroSD card (SDXC, SDHC pre-installed)

1.9 1

Custom tool with magnet

1.10 1

Outer shell

1.11 3

Stainless steel washers 5.3 mm dia.

1.12 3

Dowels 8 mm

1.13 3

Stainless steel wood screws 4.5x60 mm with Torx head

TX20

1.14 1

Torx wrench TX20

1.15 1

Allen wrench 3 mm

Connections and Initial Operation of the D16

You can nd detailed information on the installation connections and of the D16 in the

D15 Camera Manual

(PDF, available on www.mobotix.com >

Support > Manuals).

Please note that the boot options of this camera have changed compared to its predecessor (see

«Boot Options of the D16» on page 2

). Regarding

the rest of the initial operation of the D16, please see the

D15 Camera Manual

Chapter 3, «Initial Operation»

Slot for MicroSD card

Network

connector (*)

USB

L key

(magnetic,

inside housing)

Connectors

Dome thread

Camera

housing

Lenses

Outer shell

LEDs/PIR

Dome

* To suppress electromagnetic interferences, attach the enclosed hinged ferrite (item 1.7) directly behind the RJ45 connector of the camera's network

patch cable, see illustration.

Preparing the D16 for Installation

To facilitate the installation of the camera, you should complete the following tasks before actually installing the camera.

Preparatory Steps

Make sure that the condensed water outlets are pointing downwards when

planning the installation 1.

Remove the outer shell by pressing the magnetic custom tool into the three

holes of the outer shell one by one 2. Gently li the shell near each hole

to loosen the shell from its seats.

Next, unscrew the dome 3.

Insert the Individual Lens Units (1.2a)

Remove the center lock screw and the washer 1.

Insert the lens units into the seatings 2.

Insert the center lock screw and the washer and lightly tighten the screw

to keep the lens units

1.2a

in place 3. Do not overtighten the lock screw

so you can adjust the lens units later on.

Insert the Lens Bridge (1.2b/c)

Remove the center lock screw and the washer 1.

Disassemble the lens bridge by removing the two Allen screws with washers

2 (Pano lens bridge

1.2b

shown, similar for Fix lens bridge

1.2c

Insert the two brackets for the lens bridge into the seatings of the camera

housing 3.

Insert the center lock screw and the washer and lightly tighten the screw

to keep the brackets in place 4.

Insert the lens bridge between the brackets

, insert the two Allen screws

with the washers and lightly tighten the screws 6. Do not overtighten

the two screws so you can adjust the lens bridge later on.

Connect the Sensor Cables

Remove the protective covers of the image sensor connectors 1.

Connect the camera's sensor cables according to the color codes

. While

doing so, avoid twisting the sensor cables as much as possible.

Press the cable into the groove of the board 3. Take care that the wires

are not bent sharply at the plug, but that they are running in an arc.

Press the protective covers onto the connectors until they click into place

Insert the Lenses (Lens Bridges Only)

Remove the protective covers of the lens mounts and screw in the lenses.

Lens focus will be adjusted aer installing the camera and bringing it into

service (see

«Initial Operation of the D16»

1.2a

1.2b

1.2b 1.2c

Lens units

(individually adjust-

able)

2 image sensors on

Pano lens bridge 2 image sensors on

Fix lens bridge

With Outdoor Wall Mount With Corner and Pole Mount

and Outdoor Wall Mount

With Vandalism Set

Mounting Options of the D16

Installation on Walls or Ceilings Without Accessories

Aer drilling the holes for xtures (see

«Drilling Template for Installation

Without Accessories»

), attach the housing of the D16 at the designated

position using dowels and screws, then connect the cabling. Once the

power supply has been established, you will adjust the lens units or bridges

(whichever applies) and the lenses' focus (see

«Initial Operation of the D16»

Finally, you will install the dome and the outer shell.

Installation With Outdoor Wall Mount (Accessory)

Remove the cover plate of the Outdoor Wall Mount. Aer drilling the holes

for xtures (see

«Drilling Template for Installation Without Accessories»

attach the Outdoor Wall Mount at the designated position using dowels

and screws, then lead the cabling into the mount. Next, connect the cabling

and install the camera on the cover plate of the Outdoor Wall Mount using

the supplied screws. Then attach the cover plate with the camera to the

Outdoor Wall Mount.

For more information, please see the

D15 Camera Manual

Section 2.4,

«Mounting the Camera with Outdoor Wall Mount»

Installation With Corner and Pole Mount and Outdoor Wall Mount

(Accessory)

Lead the cabling from the rear through the Corner and Pole Mount and

attach it at the corner of a building or a pole (using steel straps). Then

attach the Outdoor Wall Mount to the Corner and Pole Mount.

The remaining installation of the D16 follows the steps under

«Installation

With Outdoor Wall Mount (Accessory)»

above.

Installation of the Vandalism Set (Accessory)

Remove the outer shell and the dome (see

«Preparing the D16 for Instal-

lation»

). Screw in the reinforced dome and hold the stainless steel ring

of the Vandalism Set in position to mark the holes for drilling (the bulge

in the steel ring covers the LED/PIR dome – see red circle in gure on the

right). Drill the holes for the mounting screws (or the dowels, whichever

applies), then apply the stainless steel ring and fasten it using the supplied

security screws.

75 mm/2.95 in

75mm/2.95in

Dia. 205mm/8.07in

Universal 6MP Dome Camera With

Two Lenses for Ceiling, Wall and Pole

Mounting

MOBOTIX 6MP camera for exible use in indoor and

outdoor applications, available as complete D16

DualDome (Day or Night) with lenses 6D/N/L036 to 237 and

with dierent lens bridge options.

More information:

www.mobotix.com > Products > Outdoor Cameras > D16

Inserting/Exchanging the SD Card

All camera models can use the integrated MicroSD card (SDHC) to record video data. In order to exchange the MicroSD card, please proceed as outlined

in the following instruction. For information on reliable SD cards, please see the MOBOTIX website www.mobotix.com > Support > MxMedia Library >

Planning in the document

MicroSD Card Whitelist for MOBOTIX Cameras

When replacing the SD card, make sure that recording has been deactivated in the browser (Admin Menu > Storage > Storage on External File Server /

Flash Device; activate recording again in the same dialog aer exchanging the card).

1. Remove the SD Card

Remove the outer shell and the cable cover of

the camera. If a MicroSD card has been installed,

gently press with your nger as indicated by

the arrow until you hear a

click

. Then release

the SD card. The card is protruding slightly and

can be easily removed.

2. Insert the SD Card

Insert the MicroSD card and gently press with

your nger as indicated by the arrow until you

hear another

click

. Make sure that the SD card

is fully inserted. Re-attach the cable cover and

the outer shell of the camera.

Click!

*: with rmware version 5.0.1 and higher

Produkt Specifikationer

Mærke:	Mobotix
Kategori:	Overvågningskamera
Model:	MX-D16A-F-6D6N061
Kode for international beskyttelse (IP):	IP54
Type:	IP-sikkerhedskamera
Højde:	108 mm
Vægt:	750 g
Produktfarve:	Hvid
USB-port:	Ja
Formfaktor:	Kuppel
Indbyggede højttaler(e):	Ja
Opbevaringstemperatur (T-T):	-30 - 60 °C
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Understøttede videoformater:	H.264, M-JPEG, MxPEG
Strømforbrug (typisk):	7 W
Maksimal opløsning:	1280 x 720 pixel
Hurtig installationsvejledning:	Ja
Understøttede grafikopløsninger:	1280 x 720 (HD 720), 1920 x 1080 (HD 1080), 2048 x 1536 (QXGA), 2592 x 1944
Forbindelsesteknologi:	Ledningsført
Certificering:	EN55032:2012, EN55022:2010, EN55024:2010, EN61000-6-1:2007, EN61000-6-3:2007+A1:2011, EN61000-6-4:2007+A1:2011, AS/ NZS, CISPR22:2009+A1:201
Netværksstandarder:	IEEE 802.1x
Understøttede netværksprotokoller:	IPv4, IPv6, HTTP, HTTPS, FTP, SFTP, RTP, RTSP, UDP, SNMP, SMTP, DHCP (client and server), NTP (client and server), SIP (client and server) G.711 (PCMA and PCMU) and G.722
LED-indikatorer:	Ja
Strømkilde type:	PoE
Monteringstype:	Loft/væg
Diameter:	205 mm
Full HD:	Ja
Understøttet placering:	Indendørs & udendørs
Indbygget mikrofon:	Ja
Sensortype:	CMOS
Samlet antal megapixels:	6 MP
Fokusindstilling:	1.8
Progressiv scanning:	Ja
Strøm over Ethernet (PoE):	Ja
Dag/nat funktion:	Ja
IK kode:	IK10
Minimumsbelysning:	0.001 Lux
Optisk sensorstørrelse:	1/1.8 "
Antal effektive pixels (HxV):	3072 x 2048 pixel
Zoom kapacitet:	Ja
Fast brændvidde:	6.1 mm
Nattesyn:	Ja
Billedhastighed:	42 fps
Ethernet-grænsefladetype:	Hurtigt ethernet
Antal kameraer:	1
Bevægelsessensor:	Ja
Objektivtype:	Bredvinklet
PTZ-kontrol:	Ja
Skruer inkluderet:	Ja
Temperaturføler:	Ja
Hukommelseskort inkluderet:	MicroSD
Inkluderet hukommelseskort størrelse:	4 GB
Objektivets synsvinkel, vandret:	60 °
Objektivets synsvinkel, lodret:	45 °
PTZ-tilstande:	Digital PTZ
Bevægelsessensor teknologi:	Passiv infrarød (PIR) sensor