Mobotix MxThinClient Manual

Mobotix Tynd klient MxThinClient

Læs gratis den danske manual til Mobotix MxThinClient (2 sider) i kategorien Tynd klient. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Mobotix MxThinClient, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Mx-A-TCLIENTA

32.931-002_EN_07/2017

Quick Install

MxThinClient

Standard Delivery

MxThinClient

IP Video Interface for Display

on a Monitor/TV Panel

High-resolution display of cameras and door

stations on a monitor or TV panel.

More information:

www.mobotix.com > Products > Accessories > MxThinClient

• MxThinClient

• 2 adhesive tape strips, white

Required accessories

(not included in delivery):

• Ethernet cable RJ45

• HDMI cable (Micro HDMI), fully shielded, type

A to type D

• If the MxThinClient is installed using screws,

only use at-head screws (max. dia. of screw

head 10 mm, max. dia. of thread 5 )

Installation Instructions

1. Fasten the MxThinClient

Place the MxThinClient besides the TV or monitor.

You can also use the supplied adhesive tape stripes

or screws to fasten the box at the desired position

(screws are not part of the delivery).

2. Connect the cables

1. Connect MxThinClient to the TV/monitor using

an HDMI cable.

2. Switch to the proper HDMI channel on the TV/

monitor.

Connect MxThinClient to a free PoE port of a switch

using an RJ45 Ethernet patch cable.

Note: If the steps above are not followed in the

order listed, some display devices may not show

any image at all.

Note: Make sure that the devices have a native HDMI

connector; adapters cannot be used.

Connection Example

MOBOTIX MxThinClient

Mx-A-TCLIENTA

Camera and/or

Door Station

TV/Monitor

Ethernet cable RJ45 Ethernet cable RJ45

HDMI cable type A to type D

Features of the MxThinClient

Using the MxThinClient, you can show live streams of

MOBOTIX P3 or Mx6 cameras or static images (JPEG or

PNG) on a TV or monitor with HDMI input. The following

two main features are available:

• Sequencer Feature:

By default, the integrated sequencer automatically

cycles through all dened image sources (cameras and

still images). For this purpose, you can set a global

time to show an image source and also individual

times to show specic image sources.

•

Automatic Pop-Up Feature (via MxMessageSystem)

On top of the automatic sequencer, the device can

also show an image source as a reaction to specic

events. For example, you can use this mechanism to

show the live video stream from a door station aer

someone rang the doorbell. To be able to use this

feature, MxMessageSystem must be congured both

on the camera and on the MxThinClient The image

source will pop up aer the device has received an

MxMessageSystem notication with the specied

message name.

Note: If the MxThinClient is attached to a TV or monitor

with several HDMI inputs and the device receives a

message to switch to a specic image source, the

device cannot automatically switch to the proper

HDMI input.

To congure the image sources and all other relevant

settings, please use a web browser and follow the

instructions on the following page.

MOBOTIX AG

Kaiserstrasse

D-67722 Langmeil

Phone: +49 6302 9816-103

Fax: +49 6302 9816-190

sales@mobotix.com

www.mobotix.com

Declaration of Conformity: www.mobotix.com > Support > MxMedia Library > Certicates

MOBOTIX, the MX logo, MxControlCenter, MxEasy, MxPEG and MxActivitySensor are trademarks of MOBOTIX AG

registered in the European Union, the U.S.A., and other countries • Information subject to change without notice

• MOBOTIX does not assume any liability for technical or editorial errors or omissions contained herein • All rights

reserved • © MOBOTIX AG 2017

Operating the MxThinClient

Open the MxThinClient User Interface in a Browser

Enter the IP address of the MxThinClient:

http://<MxThinClient IP address>

By default, the MxThinClient has been set to run as

a DHCP client with an additional static IP address

in the 10.x range (network mask 255.0.0.0) printed

on the housing of the device. If you are running the

MxThinClient in a network with a DHCP server (e.g.,

DSL router), you can look up the IP address in the

list of devices of the DHCP server. When using a DSL

router with integrated DHCP/DNS server, you can also

use the host name of the device MxThinClient<10x

factory IP address> in the browser address bar.

Example:

http://MxThinClient10-7-35-193

2. Set the Language and Change the Password

The factory default language is English. If required,

click on Page Administration > Language and select

a dierent language.

For security reasons, you should change the factory

default password. Click on Page Administration >

Change password for the web access and set a new

password.

3. Set Up the Network

If you intend to use the pop-up feature to show image

sources via MxMessageSystem described above, you

need to adjust the settings in the following dialogs of

the section:Conguration

• Network settings: NTP

When using messages of the MxMessageSystem,

the time of the MxThinClient must run in sync with

the cameras and door stations that are sending

the messages. In the section, enable the time NTP

synchronization and enter the same time server

(IP address or name) as on the cameras and door

stations. Note that you can also use a camera or a

door station as a time server.

• Network settings: MxMessageSystem – Distri-

bution of Message over the Network

Activate this section if you want to receive mes-

sages from a camera or door station via the

MxMessageSystem.

Important: Make sure that these entries are identical

to the entries in the MxMessageSystem congura-

tion of all cameras or door stations that are sending

messages.

Congure the Image Sources (Cameras/Still Images)

Open the dialog to Conguration > Image Sources

dene all image sources (live video streams and/or

images) you want to display as well as the correspond-

ing display duration..

Notes:

• To display still images, set the dropdown to Codec

Image and then specify the p[s] or http[s] address

to download the image to show. These images are

currently not stored in the MxThinClient, but will be

loaded every time they are displayed.

• By default, all dened image sources are displayed

using the global sequencer display duration. To

dene an individual display duration for an image

source, activate the Use Individual Display Dura-

tion option.

• If you enter the name of a message in the Message

Name eld, the device will automatically display this

image source if it receives a message with this name.

Safety Warnings

•

This product must not be used in explosion-hazard-

ous locations.

• The MxThinClient is intended for indoor use only.

Make sure to respect the operating temperature

range of 0 to +40 °C for the MxThinClient.

• Network security: MOBOTIX products include all of

the necessary conguration options for operation in

Ethernet networks in compliance with data protec-

tion laws. The operator is responsible for the data

protection concept across the entire system. The

basic settings required to prevent misuse can be con-

gured in the soware and are password-protected.

This prevents unauthorized parties from accessing

these settings.

•

Make sure that you adhere to all relevant laws, regula-

tions and that you fulll all certication requirements

for the intended use.

Technical Specications

Connections

Ethernet 100Base-T (RJ45); HDMI type

D (Micro HDMI)

Certications

EN55032:2012; EN55022:2010;

EN55024:2010; EN50121-4:2015;

EN61000-6-1:2007;

EN61000-6-2:2005;

EN61000-6-3:2007 + A1:2011;

EN61000-6-4:2007 + A1:2011;

AS/NZS CISPR22:2009 + A1:2010;

CFR47 FCC part15B

Video Codec MxPEG/M-JPEG

Formats (codecs)

for Still Images PNG, JPG, up to 10 MB

Camera Soware Release 4.4.x/5.0.x or higher

Power Consump-

tion 2 W

Power Supply PoE IEEE 802.3af

Protocols IPv4, HTTP, HTTPS, NTP, FTP, FTPS,

HDMI 1.4

Max. Image Size Full HD

Output Image

Sizes

- Image size of image source

unaltered (max. Full HD)

- VGA (640x480), SVGA (800x600),

XGA (1024x768), HD (1280x720),

Mega (1280x960), Full-HD (1920x720)

- When showing dual images,

the x value of the image sizes from

above is used

Operating Con-

ditions

Only for indoor applications,

0 to +40 °C

Protection Class IP20

Dimensions (height x width x depth): 25 x

100 x 80 mm/1 x 3.94 x 3.15 in

Materials Housing: Polycarbonate, black

Weight Approx. 125 g

Produkt Specifikationer

Mærke:	Mobotix
Kategori:	Tynd klient
Model:	MxThinClient
Kode for international beskyttelse (IP):	IP20
Bredde:	100 mm
Dybde:	80 mm
Højde:	25 mm
Vægt:	125 g
Produktfarve:	Sort
Antal HDMI-porte:	1
Ethernet LAN-porte (RJ-45):	1
Ethernet LAN:	Ja
Strømforbrug (typisk):	2 W
Driftstemperatur (T-T):	0 - 40 °C
Intern hukommelse:	1 GB
Certificering:	EN55032:2012; EN55022:2010;\nEN55024:2010; EN50121-4:2015;\nEN61000-6-1:2007;\nEN61000-6-2:2005;\nEN61000-6-3:2007 + A1:2011;\nEN61000-6-4:2007 + A1:2011;\nAS/NZS CISPR22:2009 + A1:2010;\nCFR47 FCC part15B
Kabelteknologi:	10/100Base-T(X)
LED-indikatorer:	PoE
Harmoniseret systemkode (HS):	84713000
Processorfrekvens:	- GHz
Samlet lagringskapacitet:	- GB
Understøttede protokoller:	IPv4, HTTP, HTTPS, NTP, FTP, FTPS