Monoprice 38161 Manual

Monoprice Ikke kategoriseret 38161

Læs gratis den danske manual til Monoprice 38161 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Monoprice 38161, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

8-Channel Speaker

8-Channel Speaker8-Channel Speaker Zone Hub

Zone Hub

Zone Hub Zone Hub

P/N 38161

Quick Install Guide

Quick Install GuideQuick Install Guide

INTRODUCTION

INTRODUCTION INTRODUCTION

This 8-Channel Speaker Zone Hub is designed to connect up to eight pairs of speakers to a

single amplifier or receiver. It uses removable terminal blocks for easy connection for the

speaker wires. Note that this speaker selector does not include impedance matching

circuitry, so the use of impedance matching volume controls are highly recommended to

prevent damage to the amplifier caused by low impedance loads.

INSTALLATION

INSTALLATION INSTALLATION

Perform the following steps to install this speaker selector.

1. Remove one of the black colored terminal blocks from the rear of the speaker

selector.

2. Strip approximately 1/4" of insulation from each end of each speaker wire.

3. Using a small flathead screwdriver, loosen the screws on the terminal block.

4. Insert each end of the left channel positive speaker wire into the terminal and

L+

L+L+

the negative speaker wire into the terminal, then tighten the screws to secure

L-

L-L-

them in place.

5. Insert each end of the right channel positive speaker wire into the terminal and

R+

R+R+

the negative speaker wire into the terminal, then tighten the screws to secure

R-

R-R-

them in place.

6. Insert the terminal block into the rear of the speaker selector.

7. Connect the left and right channel speaker wires into the terminals on your speaker,

taking care to match the polarity.

8. Repeat for the other seven speakers and black terminal blocks.

9. Remove the red colored terminal block from the rear of the speaker selector.

10. Strip approximately 1/4" of insulation from each end of each speaker wire.

11. Using a small flathead screwdriver, loosen the screws on the terminal block.

12. Insert each end of the left channel positive speaker wire into the terminal and L+

L+

L+L+

the negative speaker wire into the terminal, then tighten the screws to secure

L-

L-L-

them in place.

13. Insert each end of the right channel positive speaker wire into the terminal and R+

R+

R+R+

the negative speaker wire into the terminal, then tighten the screws to secure

R-

R-R-

them in place.

14. Insert the terminal block into the rear of the speaker selector.

15. Connect the left and right channel speaker wires into the terminals on your

amplifier, taking care to match the polarity.

Produkt Specifikationer

Mærke:	Monoprice
Kategori:	Ikke kategoriseret
Model:	38161

Har du brug for hjælp?

Hvis du har brug for hjælp til Monoprice 38161 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Monoprice Manualer

Monoprice 38161 Manual

5 September 2024

Monoprice 6200 Manual

30 August 2024

Monoprice 602125 Manual

21 August 2024

Monoprice 4654 Manual

19 August 2024

Monoprice 600125 Manual

19 August 2024

Monoprice 15722 Manual

18 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Smeg CVI120GE Manual

17 Juni 2025

Panduit VS-CKP4-000 Manual

17 Juni 2025

Yamazen LTH-2BH Manual

17 Juni 2025

Philips ASH4511CH Manual

17 Juni 2025

Yamazen MNW-1890CJ Manual

17 Juni 2025

D-Link DMC-700SC Manual

17 Juni 2025

Makita DHP490 Manual

17 Juni 2025

Royal Catering RC-BFWH12030 Manual

17 Juni 2025

Makita TW011G Manual

17 Juni 2025

Philips 50BDL2050Q Manual

17 Juni 2025