Moxa NPort 5110A Manual

Moxa Server NPort 5110A

Læs gratis den danske manual til Moxa NPort 5110A (4 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om Moxa NPort 5110A, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

— 1— — 2 — — 3 —

NPort 5100A Series

Quick Installation Guide

Second Edition, June 2010

1. Overview

NPort 5100A series device servers are compact, palm-sized data

communication devices that allow you to control RS-232 (NPort 5110A),

RS-422/485 (NPort 5130A), and RS-232/422/485 (NPort 5150A) serial

devices over a TCP/IP-based Ethernet.

Note: “-T” indicates an extended temperature model.

2. Package Checklist

Before installing the NPort 5100A series device server, verify that the

package contains the following items:

y 1 NPort 5100A serial device server

y Power Adaptor (NPort 5100A-T doesn't include this accessory)

y 4 stick-on pads

y Document & Software CD

y Quick Installation Guide

y Product Warranty Statement

Optional Accessory

y DK-35A: DIN-Rail Mounting Kit (35 mm)

Notify your sales representative if any of the above items are missing or

damaged.

3. Hardware Introduction

As shown in the following figures, NPort 5100A series device servers

have one male DB9 port for transmitting RS-232 (NPort 5110A),

RS-422/485 (NPort 5130A), or RS-232/422/485 (NPort 5150A) serial

data.

Top Panel View

DIN-Rail

screw hole

Wallmount

screw hole

Ready

Link

Tx/Rx

Serial Device Server

5110A

10/100M

Ethernet

RESET

12-48VDC

Port 1 RS-232

Male DB9 serial port

Front Panel View

RJ45 10/100M Ethernet port

Reset button

Power input

Rear Panel View

Stick-on pad

NOTE: The NPort 5110A, NPort 5130A, and NPort 5150A have the

same form factor.

Reset Button—Press and hold the Reset button for 5 seconds to load

factory defaults: Use a pointed object, such as a straightened paper clip or

toothpick, to depress the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, release the reset

button.

LED Indicators—NPort 5100A’s top panel has three LED indicators,

which are described in the following table.

LED

Name

LED

Color LED Function

Steady on: Power is on and the NPort is booting up.

Red Blinking: Indicates an IP conflict, or DHCP or

BOOTP server is not responding properly.

Steady on: Power is on and the NPort is functioning

normally.

Green Blinking: The NPort has been located by the NPort

Administrator’s Location function.

Ready

Off Power is off, or a power error..

Orange 10 Mbps Ethernet connection.

Green 100 Mbps Ethernet connection. Link

Off Ethernet cable is disconnected.

Orange Serial port is receiving data.

Tx/Rx

Green Serial port is transmitting data.

Off No data is being transmitted or received through the

serial port.

Adjustable pull high/low resistor for RS-422/485 (150 KΩ or 1 KΩ)

JP3

JP4

Jumpers are used to set the pull high/low

resistor values. The default is 150 KΩ. Short

the jumpers to set this value to 1 KΩ. Do not

use the 1 KΩ setting with RS-232 mode, since

doing so will degrade the RS-232 signals and

shorten the communication distance.

4. Hardware Installation Information

STEP 1: After removing the NPort 5100A series device server from the

box, the first thing you should do is connect the power adaptor.

STEP 2: Connect the NPort 5100A series device server to a network. Use

a standard straight-through Ethernet cable to connect to a hub or switch.

When setting up or testing the NPort 5100A series device server, you

might find it convenient to connect directly to your computer’s Ethernet

port. In which case, use a cross-over Ethernet cable.

STEP 3: Connect the NPort 5100A series device server’s serial port to a

serial device.

STEP 4: Placement options.

In addition to placing the NPort 5100A on a desktop or other horizontal

surface, you may also make use of the DIN-Rail or Wall Mount options,

as illustrated below.

Wall Mount DIN-Rail

Ready

Link

Tx/Rx

Serial Device Server

5110A

10/100M

Ethernet

RESET

Port 1 RS-232

12-48 VDC

P/N: 1802051000021

Produkt Specifikationer

Mærke:	Moxa
Kategori:	Server
Model:	NPort 5110A
Vægt:	340 g
Opbevaringstemperatur (T-T):	-40 - 85 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 60 °C
Ethernet LAN-datahastigheder:	10, 100 Mbit/s
Dimensioner (BxDxH):	52 x 80 x 22 mm
Certificering:	CE, FCC
Understøttede netværksprotokoller:	ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, HTTP, SMTP, IGMP v1/2
Indgangsspænding:	12 - 48 V
Kompatible operativsystemer:	SCO Unix, OpenServer\nUnixWare v2.1, v7\nUnix SVR 4.2\nUnix QNX 4.25, QNX 6\nSolaris 10\nFreeBSD\nAIX 5.x\nHP-UX 11i\nMac OS v10.3\nLinux v2.4.x, v2.6.x
Isolering:	1.5 kV
Administrationsprotokoller:	SNMP v1
Seriel grænsefladetype:	RS-232
Antal serielle porte:	1
Sikkerhed:	UL, LVD