Moxa NPort 5210-P-ST Manual

Moxa Server NPort 5210-P-ST

Læs gratis den danske manual til Moxa NPort 5210-P-ST (4 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Moxa NPort 5210-P-ST, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

— 1 — — 2 — — 3 —

NPort 5200-P Series

Quick Installation Guide

Second Edition, July 2006

1. Overview

Welcome to the programmable NPort 5200-P series, a compact

palm-sized data communication device that allows you to control RS-232

(NPort 5210-P) or RS-232/422/485 (NPort 5230-P) serial devices over a

TCP/IP-based Ethernet.

2. Package Checklist

Before installing the NPort 5210-P/5230-P, verify that the package

contains the following items:

NPort 5210-P/5230-P

y 1 NPort 5210-P/5230-P 2-port Serial Device Server

Optional Accessories

y DK-35A DIN-Rail Mounting Kit (35 mm)

y CBL-RJ45M9-150

y CBL-RJ45F9-150

y CBL-RJ45M25-150

y CBL-RJ45F25-150

RJ45 (8-pin) to DB9 (M) cable, 150 cm

RJ45 (8-pin) to DB9 (F) cable, 150 cm

RJ45 (8-pin) to DB25 (M) cable, 150 cm

RJ45 (8-pin) to DB25 (F) cable, 150 cm

y DIN-Rail Power Supply and Adaptor

NPort 5210-P-ST/5230-P-ST

y 1 NPort 5210-P/5230-P 2-port Serial Device Server

y Documentation & Software CD

y NPort 5210-P/5230-P Series Quick Installation Guide

y Switching power adapter

y Power Jack to Terminal Block Cable

y Power Cord

y Product Warranty

y Turbo C Linense Card

y RJ45 to RJ45 Ethernet cross-over cable

y CBL-RJ45M9-150 x 2 (NPort 5210-P-ST Only)

Notify your sales representative if any of the above items is missing or

damaged.

3. Hardware Introduction

As shown in the following figures, NPort 5210-P has two 8-pin RJ45

ports, both for the RS-232 interface, NPort 5230-P has one 10-terminal

terminal block, with 5 pins used for one RS-232 port, and 5 pins used for

one RS-422/485 port.

NPort 5210-P NPort 5230-P

10/100M

Ethernet

Port 2

RS-232

Port 1

RS-232

Ready

Link

Industrial RS-232 Device Server

5210-P

RESET

RJ45 10/100 Mbps

Ethernet port

Reset button Terminal Block

Power input

DIN-Rail

screw hole

Wallmount

screw hole

5210

Industrial RS-232/422/485 Device Server

5230-P

10/100M

Ethernet

Ready

Link

P1 RS-232

RTS

CTS

GND

T+

T-

R+/D+

R-/D-

GND

P2 RS-485/422

RESET

RS-232 & RS-422/485

Terminal Block

RJ45 (8-pin) serial ports

V+V-

12-48V

V+V-

12-48V

Reset Button—Press the Reset button continuously for 5 sec to load

factory defaults: Use a pointed object, such as a straightened paper clip or

toothpick, to press the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, you should release

the reset button.

LED Indicators—The top panels of NPort 5210-P/5230-P have four

LED indicators, as described in the following table.

LED Name LED Color LED Function

red

Steady on: Power is on and NPort 5200-P

series is booting up.

Blinking: Indicates an IP conflict, or

DHCP or BOOTP server did

not respond properly.

green

Steady on: Power is on and NPort 5200-P

series is functioning normally.

Blinking: The device server has been

located by Administrator’s

Location function

Ready

off Power is off, or power error condition

exists.

orange 10 Mbps Ethernet connection.

green 100 Mbps Ethernet connection.

Link

off Ethernet cable is disconnected, or has a

short.

orange Serial port is receiving data.

green Serial port is transmitting data.

P1, P2

off No data is being transmitted or received

through the serial port.

4. Hardware Installation Procedure

STEP 1: After removing NPort 5210-P/5230-P from the box, the first

thing you should do is connect the power adaptor. Connect the 12-30

VDC power line with NPort 5210-P/5230-P’s terminal block, or connect

the DIN-Rail power supply with NPort 5210-P/5230-P’s terminal block.

STEP 2: Connect NPort 5210-P/5230-P to a network. Use a standard

straight-through Ethernet cable to connect to a Hub or Switch. When

setting up or testing NPort 5210-P/5230-P, you might find it convenient

to connect directly to your computer’s Ethernet port. In this case, use a

cross-over Ethernet cable.

STEP 3: Connect NPort 5210-P/5230-P’s serial port to a serial device.

STEP 4: Placement Options

In addition to placing

NPort 5210-P/5230-P

on a desktop or other

horizontal surface, you

may also make use of

the DIN-Rail or Wall

Mount options, as

illustrated here.

Wall Mount

5210

10/100M

Ethernet

Port 2

RS-232

Port 1

RS-232

Ready

Link

Industrial RS-232 Devic e Server

5210-P

RESETV+V-

12-30V

DIN-Rail

P/N:1802052003000

Produkt Specifikationer

Mærke:	Moxa
Kategori:	Server
Model:	NPort 5210-P-ST
Vægt:	340 g
Opbevaringstemperatur (T-T):	-40 - 85 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 55 °C
Ethernet LAN-datahastigheder:	10, 100 Mbit/s
Certificering:	FCC Class A, CE Class A
Understøttede netværksprotokoller:	ICMP, IP, TCP, UDP, DHCP, BootP, Telnet, DNS, SNMP, HTTP, SMTP, SNTP
Kompatible operativsystemer:	Windows 95/98/ME/NT/2000/XP/2003/Vista\r\nWindows XP/2003/Vista/2008/7/8\r\nSCO Unix\r\nSCO OpenServer\r\nUnixWare 7\r\nUnixWare 2.1, Unix SVR 4.2\r\nUnix QNX 4.25, QNX 6\r\nSolaris 10\r\nFreeBSD\r\nAIX 5.x\r\nHP-UX 11i
Administrationsprotokoller:	SNMP v1
Seriel grænsefladetype:	RS-232
Antal serielle porte:	2
Baud hastighed:	230.4 Kbit/s
RS-232 signaler:	CTS, DCD, DSR, DTR, GND, RTS, Rx, Tx
Sikkerhed:	UL, CUL, TÜV