Moxa NPort 5430 Manual

Moxa Server NPort 5430

Læs gratis den danske manual til Moxa NPort 5430 (4 sider) i kategorien Server. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Moxa NPort 5430, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

P/N: 1802054000312

NPort 5400 Series Quick

Installation Guide

Sixth Edition, January 2011

1. Overview

Welcome to Moxa NPort 5400, a 4 port communication device that

allows you to control RS-232 (for NPort 5410), RS-422/485 (for

NPort 5430/5430I) or RS-232/422/485 (for NPort 5450/5450I)

serial devices over a TCP/IP based Ethernet. Besides, NPort

5450-T and NPort 5450I-T are designed to use in wide

temperature environment.

NPort 5400 Series is a Moxa Green Product. Moxa’s Green Products

satisfy the RoHS directive of the European Parliament, and

accordingly, do not contain cadmium and cadmium compounds,

hexavalent chromium compounds, lead and lead compounds,

mercury and mercury compounds, PBBs (polybrominated

biphenyls), or PBDEs (polybrominated diphenyl ethers).

2. Package Checklist

Before installing NPort 5400, verify that the package contains the

following items:

• 1 NPort 5400 4-port Serial Device Server

• Power Adaptor (NPort 5450-T and 5450I-T do not include this

accessory)

• Power jack to 3-pin terminal block adaptor

• Wall mount kit

• Documentation and software CD

• Quick Installation Guide

• Warranty card

Optional Accessories

• DK-35A For 35 mm DIN-Rail; includes 4 screws

Notify your sales representative if any of the above items is missing or

damaged.

3. Hardware Introduction

As shown in the following figures, NPort 5410 has 4 Male DB9 ports,

for the RS-232 interface, NPort 5430/5430I has 4 5-pin terminal

blocks, for the RS-422/485 interface, and NPort 5450/5450I has 4

Male DB9 ports, for the RS-232/422/485 interface.

NPort 5410/5450/5450I

RJ45 10/100 Mbps Ethernet port

Power Jack Power Input

Terminal Block power input

RESET

LCM display panelIndicator LEDs Input buttons

Male DB9 serial port

Serial Device Server

5410

NP5410_61405

192.168.127.254

LAN V+ V-

Port 1

RS-422/785

Port 2

RS-422/785

Port 3

RS-422/785

Port 4

RS-422/785

NPort 5430/5430I

RJ45 10/100 Mbps Ethernet port

Terminal Block power input

RE SE T

Power Jack Power Input

M display panelIndicator LEDs Input buttons

Serial Device Server

5430

NP 5410_61405

192.168.127.254

LAN V+ V-

RS-422/485 Terminal Block

T+ T- R+

D+

R-

D-

GND T+ T- R+

D+

R-

D-

GND T+ T- R+

D+

R-

D-

GND T+ T- R+

D+

R-

D-

GND

Port 1

RS-422/785

Port 2

RS-422/785

Port 3

RS-422/785

Port 4

RS-422/785

NPort 5450-T/5450I-T

RJ45 10/100 Mbps Ethernet port

Terminal Block power input

RE SE T

Indicator LEDs

Power Jack Power Input

Male DB9 serial port

Serial Device Server

5450

LAN V+ V-

Port 1

RS-422/785

Port 2

RS-422/785

Port 3

RS-422/785

Port 4

RS-422/785

Reset Button—Press the Reset button continuously for 5 sec to

load factory defaults: Use a pointed object, such as a straightened

paper clip or toothpick, to press the reset button. This will cause

the Ready LED to blink on and off. The factory defaults will be

loaded once the Ready LED stops blinking (after about 5 seconds).

At this point, you should release the reset button.

LED Indicators—NPort 5400’s top panel contains six LED

indicators, as described in the following table.

LED

Name

LED Color

LED Function

red Steady on: Power is on and NPort is

booting up.

Blinking: Indicates an IP conflict, or

DHCP or BOOTP server did not respond

properly.

green Steady on: Power is on and NPort is

functioning normally.

Blinking: The NPort has been located

by NPort Administrator’s Location function

Ready

off Power is off, or power error condition

exists.

orange 10 Mbps Ethernet connection.

green 100 Mbps Ethernet connection.

Ethernet

off Ethernet cable is disconnected, or has a

short.

orange Serial port is receiving data.

green Serial port is transmitting data.

P1, P2,

P3, P4

off No data is being transmitted or received

through the serial port.

LCM Display Panel (not support in -T model)—When the NPort

5400 unit is powered up, you will a see a display similar to:

P 5

0 5

1 9 2

. 1

7 . 2 5 4

This is where NP5410_61405 is the server’s name, and

192.168.127.254 is the server’s IP address.

LCM Panel Operation (not support in -T model)—There are

four buttons on NPort 5400’s top panel used to operate the

server’s LCM panel. Going from left to right, the buttons are:

Button Action

MENU Activates the main menu, or returns to a lower level.

＾ Scrolls up through a list of items shown on the LCM

panel’s second line.

﹀ Scrolls down through a list of items shown on the LCM

panel’s second line.

SEL Selects the option listed on the LCM panel’s second

line.

Detailed LCM Panel Operating instructions can be found on the

CD-ROM in the “NPort 5400 Series User’s Manual.”

– 1 – – 2 – – 3 –

Produkt Specifikationer

Mærke:	Moxa
Kategori:	Server
Model:	NPort 5430
Vægt:	740 g
Opbevaringstemperatur (T-T):	-40 - 85 °C
Relativ luftfugtighed ved drift (H-H):	5 - 95 %
Ethernet LAN-porte (RJ-45):	1
Driftstemperatur (T-T):	0 - 55 °C
Ethernet LAN-datahastigheder:	10, 100 Mbit/s
Certificering:	CE, FCC, EN 55022 Class A, FCC Part 15 Subpart B Class A, \r\nEN 55024, EN 60601-1-2 Class B, EN 55011
Understøttede netværksprotokoller:	ICMP, IP, TCP, UDP, DHCP, BOOTP, Telnet, DNS, HTTP, SMTP, SNTP, Rtelnet, ARP
Indgangsspænding:	12 - 48 V
Isolering:	1.5 kV
Flowkontrol support:	Ja
Administrationsprotokoller:	SNMP v1
Seriel grænsefladetype:	RS-422/485
Antal serielle porte:	4
Baud hastighed:	921.6 Kbit/s
Sikkerhed:	UL 60950-1, EN 60950-1
Link/Act LED:	Ja