MTX Audio WET75.2 Manual

MTX Audio Modtager WET75.2

Læs gratis den danske manual til MTX Audio WET75.2 (32 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om MTX Audio WET75.2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/32

OWNER’S MANUAL

WET SERIES AMPLIFIERS

M T X . C O M

Use your smartphone to scan or visit

youtube.com/user/MTXAudioUSA

to learn how to properly install this

ampliﬁer.

M T X . C O M

PRODUCT INFORMATION

Model #

Serial #

Dealer’s Name

Date of Purchase

INTRODUCTION

Thank you for purchasing this MTX Audio Hi-Performance marine grade ampliﬁer. Proper installation

matched with MTX speakers and subwoofers provide superior sound and performance for endless

hours of enjoyment on your boat wherever the current takes you. Congratulations and enjoy the

ultimate audio experience with MTX!

FEATURES

• Compact Size

• Double Sided PCB

• Surface Mount Components

• MOSFET Design

• LPF and HPF Crossover

• Adjustable Bass Boost

• Noise Free Design

• Short, Thermal, and High/Low Voltage Protection

• Conformal Coated PCB

• Plexiglass Cover for Controls

• Stainless Steel Hardware

• Rubber Gaskets Around RCA Connectors

CONTROL FUNCTIONS

1. Speakers - Connect speakers/subwoofers to these terminals. Be sure to check wire for proper

polarity. Never connect the speaker cables to the chassis ground.

2. +BATT (+12 Volt Power) - Connect this terminal through a FUSE or CIRCUIT BREAKER to the

positive terminal of the vehicle battery or the positive terminal of an isolated audio system

battery. WARNING: Always protect this power cable by installing a fuse or circuit breaker of the

appropriate gauge within 18 inches (45cm) of the battery terminal connection.

3. Remote Turn On - This terminal turns on the ampliﬁer when (+) 12 volt is applied to it. Connect it to

the remote turn on lead of the head unit or signal source.

4. GND - Run an equal gauge wire from the Ground (GND) terminal on the MTX ampliﬁer to the

negative terminal on the battery. Use the shortest distance possible. It is always a good idea to

replace the factory ground at this time with a cable equal or larger than the new ampliﬁer power

cable. CAUTION: Do not connect this terminal directly to the vehicle battery

ground terminal or any other factory ground points.

5. RCA Input Jacks - These RCA input jacks are for use with source units that have RCA outputs. A

source unit with a minimum level of 200mV is required for proper operation. The use of high

quality twisted pair cables is recommended to decrease the possibility of radiated noise entering

the system.

6. Gain Control - The Gain control will match the ampliﬁer’s sensitivity to the source units signal

voltage. The operating range is 5V to 200mV. This is NOT a volume control.NOTE:

Produkt Specifikationer

Mærke:	MTX Audio
Kategori:	Modtager
Model:	WET75.2
Bredde:	177.8 mm
Dybde:	76.2 mm
Højde:	25.4 mm
Produktfarve:	Hvid
Signal/støjforhold:	80 dB
Forstærker klasse:	A/B
Antal forstærkerkanaler:	2 kanaler
RMS udgangseffekt pr. kanal (4 Ohm):	75 W
Maks. udgangseffekt (RMS):	400 W
Effektivitet:	1 %
RMS udgangseffekt pr. kanal (2 ohm):	100 W
Indgangsfølsomhed:	200 mV