Naim Ovator S-400 Manual

Naim Højttaler Ovator S-400

Læs gratis den danske manual til Naim Ovator S-400 (44 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 22 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 11.5 anmeldelser. Har du et spørgsmål om Naim Ovator S-400, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/44

R E F E R E N C E M A N U A L

O V A T O R S - 6 0 0 a n d S - 4 0 0 L O U D S P E A K E R S

E N G L I S H , D E U T S C H , F R A N Ç A I S , I T A L I A N O ,

E S P A ñ O L , N E D E R L A N D S , 中文

OVATOR S-600 & S-400 – English

Introduction and Unpacking

The Ovator S-600 and S-400 are very high performance speakers that will repay eﬀort

spent on installation. It is important that you read this manual before fully unpacking

and installing your Ovators. The manual begins with unpacking instructions. Ovators

are extremely heavy and to minimise the risk of damage or personal injury you

should follow these instructions carefully. Unpacking and installing Ovators is a two-

person task and should not be attempted alone.

1 S-600 Unpacking

It is important that Ovators are unpacked as described in

the following paragraphs and illustrations.

They should be unpacked in the room in which they are to

be used and close to their likely installed positions.

Having removed this manual proceed to unpack each

Ovator following the steps below:

1.1 With the carton lying on its back, lift out the end-cap at

the base of the speaker. The speaker has front and back

castor trolleys attached to its plinth. A transit screw retains

each one. Do not remove them at this stage.

1.2 Using the foam insert located in the carton as a

wedge, push the speaker to the end of the carton so that

the trolley castors touch the cardboard.

1.3 Carefully lift the carton upright using the handles on its

sides. The Ovator is heavy – use an appropriate safe lifting

technique.

1.4 Wheel the speaker out of the carton on its trolleys,

remove remaining packaging, and wheel the speaker to

its likely installed position. Push the speaker from a point

towards the middle or below.

1.5 Remove the trolleys one at a time. Unscrew both

attachment screws then tilt the speaker backwards, using

your foot to stabilise it, and remove the front trolley when it

is clear. Lower the speaker on to its front ﬂoor-spikes and tilt

the speaker forwards to remove the rear trolley. Take care

when removing the trolleys that the Ovator ﬂoor-spikes do

not cause damage or injury.

Note: Keep all the packing, including the transit screws

and spacers. The transit screws must be replaced if the

loudspeakers are to be repacked and shipped. Tighten the

screws suﬃciently to restrain the suspension system.

1.1

1.2

1.3 1.4 1.5

Produkt Specifikationer

Mærke:	Naim
Kategori:	Højttaler
Model:	Ovator S-400
Bredde:	330 mm
Dybde:	345 mm
Højde:	1060 mm
Vægt:	31000 g
Produktfarve:	Træ
Udgangseffekt (RMS):	150 W
Anbefalet brug:	Højttalersæt enhed
Frekvensområde:	36 - 35000 Hz
Impedens:	4 ohm (Ω)
Forbindelsesteknologi:	Ledningsført
Højttaler, type:	2-vejs
Lyd-output kanaler:	1.0 kanaler
Højttaler, placering:	Gulv
Diskanthøjttaler:	Ingen
Sensitivitet:	88 dB
Bashøjttaler:	Ja
Antal bashøjttalerdrev:	2
Woofer diameter:	165 mm
Forstærker:	Ingen
Mid-range driver diameter:	46 mm
Antal mellemtoneenheder:	1