NEC WT40SN40 Manual

NEC Projektor tilbehør WT40SN40

Læs gratis den danske manual til NEC WT40SN40 (2 sider) i kategorien Projektor tilbehør. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om NEC WT40SN40, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Examples of pictograms

The symbol urges caution (including warnings).

A concrete description of the caution is indicated on the diagram.

The symbol indicates actions that should not be performed.

A concrete description of the forbidden action is indicated on the diagram.

The symbol indicates instructions that must be performed.

A concrete description of the instruction is indicated on the diagram.

WT40SN 40" Panel Screen

WT40SN Assembly Instructions

We greatly appreciate your purchase of this NEC WT40SN flat panel screen.

Read these instructions carefully to ensure proper assembly.

* The WT40SN is a panel screen exclusively for use with mirror projection type projectors.

It can be used in combination with the separately sold dedicated projector stand to form a stand with integrated screen.

M Be sure to read this section before using.

• About the pictograms

Pictograms are used in these assembly instructions and on the product to ensure proper, safe use of the product and

prevent injury to you and others as well as damage to property. The pictograms and their meanings are described

below. Be sure to understand them fully before reading the instructions.





WT40SN-0804K-01





5. Attach the caps to the frames.

Insert the caps over the upper tips of the frames.

Fasten them with the 3 × 10 screws.

The caps prevent the screen unit from coming off.

This completes assembly of the panel screen.

4. Fasten the bottom edge of the

screen to the frames.

Slide the lower lock fittings and line them up with the 

screw holes in the frame bottom edge fitting.

Fasten using two M6 × 10 screws.

3. Insert the screen unit’s upper lock

fitting into the frame and fasten

temporarily with the height adjust-

ment knobs.

Fasten the screen unit at the position of the stoppers in

the frame.

2-2. When using the screen alone

Mount the plate and stands to the

frames.

Line up the frames with the screw holes in the plate,

insert the M6 × 35 screws and fasten to the stands’

screw holes.

2-1. When mounting to a separately

sold dedicated stand

Attach the frames and plate to the dedi-

cated stand.

CAUTION

Before mounting, lock the dedicated stand’s cast-

ers, lower the top panel and tighten the height

adjustment knobs securely so that the stand is sta-

ble.

Line up the panel screen fixing holes in the dedicated 

stand with the holes in the frames.

Place the plate on the frames and fasten it to the dedi-

cated stand using the M6 × 35 screws.

* The stands included with the panel screen are not

used, so store them in a safe place.

1. Mount the two lateral bars to the

frames.

Slide the lower lock fittings to the approximate positions

shown on the diagram and fasten them in place with the

M5 × 50 screws.

M Assembling the Panel Screen

M Checking the Package Contents

Check that the following parts are included in the package.

• Heed the items below.

Failure to heed them could lead to the screen falling or

tipping over, resulting in injury or damage to the equip-

ment.

· Do not place on sloped surfaces or in unstable places.

· Do not hang from the screen, hook objects onto it or

push it.

· Do not climb onto the screen.

· Do not place any objects other than the designated

projector on the screen’s plate.

• Do not scratch the screen with metal objects, etc.

The screen’s surface is protected with an extremely hard

coating, but as a plastic material is used, rubbing hard

objects such as metal against it could scratch it.

CAUTION

• Do not make any modifications. Doing so could lead to

accidents due to the screen falling.

• Be sure to tighten the product’s screws securely. Failure

to do so could lead to the screen falling, resulting in injury

or damage to the equipment.

• Do not use the screen outdoors. Wind could cause the

screen to tip over or fall, resulting in injury or damage to

the equipment.

WARNING

Failure to heed these indications and handling improperly could lead to physical

injury or damage to surrounding property.

CAUTION

Failure to heed these indications and handling improperly could lead to physical

accidents, including death or major injury.

WARNING

NOTE

• Do not place the screen in direct sunlight or other places

exposed to high temperatures, in humid or dusty places,

or in places where it will be exposed to water or oil.

• Do not touch the screen surface. Dirt on the screen will

reduce the picture quality. If the screen surface is dirty,

apply some neutral detergent dissolved in about 20 parts

of water to a soft cloth and wipe off the dirt gently.

Avoid using benzene or thinner, as they could mar the

surface.

• When transporting the screen, do so in the same pack-

aged conditions as when it was purchased to avoid

scratches and damage.

• Keep magnetic recording media at least 10 cm away.

The screen is attached to the board by magnet. Placing

magnetic tickets, credit cards, floppy discs, video tapes,

cassette tapes or other magnetic recording media within

10 cm from the screen could lead to loss of or damage to

the recorded data.

• Do not apply adhesive tape or the like to the screen’

s surface. If cellophane or other adhesive tape is acci-

dentally stuck on the screen surface, peel it off carefully,

being sure that none of the adhesive remains. If there is

any adhesive on the screen surface, wipe it off carefully

using a neutral detergent.

Caps: 2

Frames: 2 Lateral bars: 2

Plate: 1

Stands: 2

Wires: 2 Screen unit: 1

3 × 10 screws: 2

M4 × 8 screws (with washers): 4

M5 × 50 screws: 4 M6 × 35 screws: 4

M6 × 10 screws: 4 Height adjustment knobs: 2

M5 × 50 screw

Lateral bar

Frame

Lower lock fitting

M6 × 35 screw

Plate

Frame

[Dedicated stand]

Panel screen fixing

holes

Plate

Stand

M6 × 35 screw

Frame

Screen unit

Frames

Upper

lock fitting

Stopper

Height adjustment

knob

Lower lock fitting

Frame bottom

edge fitting

M6 × 10 screws

Frames

Cap

3 × 10 screw

Frames

Produkt Specifikationer

Mærke:	NEC
Kategori:	Projektor tilbehør
Model:	WT40SN40

Har du brug for hjælp?

Hvis du har brug for hjælp til NEC WT40SN40 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Projektor tilbehør NEC Manualer

2 September 2024

3 August 2024

24 Juli 2024

22 Juli 2024

13 Juli 2024

Projektor tilbehør Manualer

Nyeste Projektor tilbehør Manualer

Metronic 451073 Manual

27 Marts 2025

Vogel's PPC 1585 Manual

27 Marts 2025

Vogel's PPC 1500 Manual

21 Februar 2025

Fromm & Starck STAR_SSD_07 Manual

30 Januar 2025

Fromm & Starck STAR_PMW_06 Manual

30 Januar 2025

Fromm & Starck STAR_MMS_04 Manual

28 Januar 2025

Barco R9853370 Manual

14 Januar 2025

Roadinger MBT-3 Manual

6 Januar 2025

Chief RPMC198 Manual

31 December 2025

Chief RPMA360 Manual

31 December 2025