Nedis WIFICO11CWT Manual

Nedis Overvågningskamera WIFICO11CWT

Læs gratis den danske manual til Nedis WIFICO11CWT (8 sider) i kategorien Overvågningskamera. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Nedis WIFICO11CWT, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Full manual Nedis SmartLife ™

Download the app: Nedis SmartLife from Apple App store or Google Play Store.

Create account

Select country code and enter full naonal phone number or email address and then

request vericaon code.

Enter received vericaon code and pick your own password.

Add device

1. Tap “+” on the top right corner. A list of potenal products appears.

2. Select the device type you want to add from the list

3. Acvate the device to be added by plugging it in or connecng the baer y.

4. Make sure the indicaon LED (or the lighng device) ashes quickly (as shown in example in the

applicaon) and tap the buon to conrm.

If the light is not ashing quickly hold the reset buon (or switch the bulb o and on for 3 mes) unl

it ashes.

5. Conrm your phone is connected to the Wi-Fi network to which the device will be added, enter the

Wi-Fi password and conrm.

6. Now the device will be searched, make sure your phone and the device are close to the router to

opmize recepon.

7. Aer the product is found and added, rename it so you can easily recognize it.

If above method fails (this can be due to unstable network or specic network protecon) add the device using

AP mode by following the steps below.

Add device (AP mode)

1. Tap “+” on the top right corner. A list of potenal products appears.

2. Select the device type you want to add from the list

3. Hold the reset buon (or switch the bulb o and on for 3 mes) unl the indicaon LED (or lighng

device) ashes (as shown in example) SLOWLY

If the light is ashing quickly, reset again by holding the reset buon for about 5 seconds or switching

the light o and on 3 mes.

4. Conrm the Wi-Fi network to which the device will be added, enter the Wi-Fi password and conrm.

5. Connect -Fi hotspot (SmartLife_xxxx) your phone to the device’s Wi

6. If asked: conrm to stay connected to Wi-Fi network without internet access

7. Go back to the Nedis SmartLife applicaon to connue installaon.

8. Now the device is sent the instrucons to connect to your exisng Wi-Fi network, make sure your

phone and the device are close to the router to opmize recepon.

9. Aer the product is found and added, rename it so you can easily recognize it.

Produkt Specifikationer

Mærke:	Nedis
Kategori:	Overvågningskamera
Model:	WIFICO11CWT
Kode for international beskyttelse (IP):	IP65
Type:	IP-sikkerhedskamera
Produktfarve:	Hvid
Kompatible hukommelseskort:	MicroSD (TransFlash)
Wi-Fi:	Ja
Formfaktor:	Kugle
Understøttede videotilstande:	1080p
Indbyggede højttaler(e):	Ja
Driftstemperatur (T-T):	-20 - 50 °C
Maksimal opløsning:	1920 x 1080 pixel
Husmateriale:	Plast
Beskyttelsesfunktioner:	Vandtæt
Understøttede grafikopløsninger:	1920 x 1080 (HD 1080)
Forbindelsesteknologi:	Trådløs
Strømkilde type:	DC
Monteringstype:	Loft/væg
Indbygget kortlæser:	Ja
Harmoniseret systemkode (HS):	85258900
Understøttet placering:	Udendørs
Understøttede mobile operativsystemer:	Android,iOS
Sensortype:	CMOS
Samlet antal megapixels:	2 MP
Lydsystem:	2-vejs
Driftsfrekvens:	2400 - 2483.5 Mhz
Dag/nat funktion:	Ja
Minimumsbelysning:	- Lux
Antal sensorer:	1
Optisk sensorstørrelse:	1/3 "
Nattesyn:	Ja
Antal kameraer:	1
Bevægelsessensor:	Ja
Linse, diameter:	2.8 mm
Antal linser:	1
Nattesyn, afstand:	15 m
Objektivets synsvinkel, lodret:	110 °