Nemco 55050AN Manual


Læs gratis den danske manual til Nemco 55050AN (2 sider) i kategorien Skæremaskine. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Nemco 55050AN, eller vil du spørge andre brugere om produktet?

Side 1/2
Operating and Maintenance Instructions
Model: 55050AN Spiral Fry™ Potato Cutter
55050AN-P Vegetable Noodler
55050AN-G Fine Cut Garnish Cutter
55050AN-R Ribbon Fry Cutter
55050AN-WR Wavy Cut Ribbon Fry Cutter
55050AN-CT Chip Twister
55050AN-WCT Wavy Chip Twister
1
IMPORTANT
1. To get the best operation and life from your machine, please read and comply with these instructions.
2. Clean machine thoroughly before and after each use using cleaning instructions below.
3. Minimize the use of alkaline cleaners as they may cause pitting and dulling of the finish.
SAFETY INSTRUCTIONS
Remember that the blades are VERY SHARP; be careful when handling and operating the machine to keep hands away from
the cutting edges.
PREPARATION
1. Remove the mounting base from the machine as it is received and install it on a tabletop. Insert the SUPPORT STAND into the
MOUNTING BASE and secure in place with the LOCK SCREW.
2. If unit fails to operate properly when first used call NEMCO customer service at 1-800-782-6761
OPERATION of Spiral Fry™
First disengage the DRIVE LEVER by lifting it off the DRIVE SCREW and letting it hang down from the SUPPORT ROD. Pull back on
CRANK until the back face of the DRIVE PLATE mounted on the rear of the DRIVE SCREW strikes the face of the stand. Push the
large diameter end of the product onto the fingers of the DRIVE PLATE and then push product, drive plate and crank forward until
CENTER SCREW is embedded in the product. Engage DRIVE LEVER by placing it over the DRIVE SCREW. Then turn CRANK
clockwise until product is completely processed. Disengage DRIVE LEVER, pull DRIVE SCREW back, remove product heel and
repeat the process.
Note: For best results, place a hand lightly on the DRIVE LEVER while turning the crank. When the DRIVE LEVER rises, stop
cranking; lift the DRIVE LEVER and pull the CRANK and DRIVE SCREW back to accept the next product. Do not continue
to crank after the DRIVE LEVER rises.
OPERATION OF RIBBON FRY, GARNISH CUTTER, & WAVY CUT
Pull back on CRANK until back face of the DRIVE PLATE mounted on the rear of the DRIVE SHAFT strikes the face of the STAND.
Push the large diameter end of the product on to the fingers of the DRIVE PLATE and then push the DRIVE PLATE and CRANK
forward until the round blade is embedded in the product. Then press the CRANK forward firmly while turning CRANK clockwise
until product is completely processed. The DRIVE LEVER is used on the spiral fry only.
CLEANING
Loosen LOCK SCREW and remove the machine from the MOUNTING BASE. The machine can be cleaned by immersing, pressure
spraying or putting it through a dishwasher.
When necessary, the machine can be easily disassembled for further cleaning as follows:
1. Remove FRONT PLATE ASSEMBLY by removing the WING NUTS.
2. The BLADES can be removed with a screwdriver. Note: CENTER SCREW has a LEFT HAND THREAD so turn
clockwise to remove.
3. Remove the DRIVE PLATE by unthreading it from the DRIVE SCREW.
4. The SUPPORT RODS can be unthreaded from the SUPPORT STAND ASSEMBLY.
5. To reassemble, reverse the procedure.
PREVENTATIVE MAINTENANCE
1. All BLADES are made of hardened Stainless Steel. They can be re-sharpened with a file or sharpening stone (except for Wavy
Cut).
2. Clean machine after each use.
SPIRAL FRY, RIBBON FRY, & WAVY FRY COOKING INSTRUCTIONS
Your new Spiral Fry is an excellent machine made of quality Stainless Steel, Aluminum and Engineered Plastics. This machine will
be one of the most profitable pieces of equipment in your kitchen. The quality of the potatoes served is directly related to the
selection of the potato, how it is stored, how it is prepared, how it is cooked and when it is served.
There are two methods of preparing your potato. One is to cut and cook to order. The other is to cut your potatoes in quantity in
advance, store or blanch, and then cook to order.


Produkt Specifikationer

Mærke: Nemco
Kategori: Skæremaskine
Model: 55050AN

Har du brug for hjælp?

Hvis du har brug for hjælp til Nemco 55050AN stil et spørgsmål nedenfor, og andre brugere vil svare dig




Skæremaskine Nemco Manualer

Nemco

Nemco 55050AN Manual

12 November 2025
Nemco

Nemco 55450-3 Manual

12 November 2025
Nemco

Nemco 55450-2 Manual

11 November 2025
Nemco

Nemco 55500-3 Manual

27 August 2025
Nemco

Nemco 56500-1 Manual

27 August 2025
Nemco

Nemco 55150B Manual

27 August 2025
Nemco

Nemco 56610-1 Manual

27 August 2025
Nemco

Nemco 55650-6 Manual

27 August 2025
Nemco

Nemco 55650-4 Manual

27 August 2025

Skæremaskine Manualer

Nyeste Skæremaskine Manualer

GARDE

GARDE 181DM14 Manual

12 November 2025
GARDE

GARDE 181DM14WM Manual

12 November 2025
GARDE

GARDE 181DM12 Manual

12 November 2025
GARDE

GARDE 181DM12WM Manual

11 November 2025
Leifheit

Leifheit 3222 Manual

29 Oktober 2025
Alpha Tools

Alpha Tools FSG 920 Manual

12 Oktober 2025
Ritter

Ritter Sinus 1 Manual

10 Oktober 2025
Ritter

Ritter Sono² Manual

10 Oktober 2025
Ritter

Ritter Markant 05 Manual

10 Oktober 2025