Netgear AGM732F Manual

Netgear Ikke kategoriseret AGM732F

Læs gratis den danske manual til Netgear AGM732F (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 62 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 31.5 anmeldelser. Har du et spørgsmål om Netgear AGM732F, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Guide

ProSafe® GBIC SFP Modules AGM731F and AGM732F

Package Contents

• ProSafe® GBIC SFP Modules AGM731F and AGM732F

• Installation Guide

Install Your Optical Module

The 1000Base-X SFP Module provides full-duplex 1000 M bps Ethernet operation in

each direction for NETGEAR managed switches.

The switch automatically detects the module, so you can simply plug it into an

available module slot. Plugging in an SFP module disables the associated RJ-45

port.

Because invisible laser radiation might be emitted

from the aperture of the port when no fiber cable is

connected, avoid exposure to laser radiation and do

not stare into open apertures.

The module can be inserted or removed while the switch is operational.

AGM731F or AGM732F

Install a Module

Insert the module firmly into the slot that supports the SFP interface. You should

hear a click when the module is firmly seated.

Remove a Module

Release the module latch by pulling down the handle bar across the module, and

pull the module out of the module slot.

Table 1. Technical Specifications

Statement of Conditions

In the interest of improving internal design, operational function, and reliability,

NETGEAR reserves the right to change the product described in this document

without notice. NETGEAR does not assume any liability that may accrue due to the

use or application of the product(s) or circuit layout(s) described herein.

Standards IEEE 802.3z

AGM731F 1000Base -SX

AGM732F 1000Base-LX

Connectors AGM731F: SC for 62.5 um or 50 um cable

AGM732F: LC for 9 um cable

Operating temperature 32 to104º F (0 to 40ºC)

Storage temperature 14 to158 ºF (–10 to 70ºC)

Operating relative humidity 10 to 90% non-condensing

Operating altitude AGM731F: up to 3 Km (10 K ft)

AGM732F: up to 10 Km (32.8 K ft)

Operating distance AGM731F: 550 m

AGM732F: 10Km

Power consumption 500 mW

MTBF AGM731F: >10 years

AGM732F: >10 years

Safety certification UL 1950, CSA 22.2 No.60 950

Environmental compliance RoHS

AGM731F-AGM732F IG 17Oct11.fm Page 1 Monday, October 17, 2011 11:54 AM

September 2011

This symbol was placed in accordance with the European Union Directive 2002/96 on the Waste

Electrical and Electronic Equipment (the WEEE Directive). If disposed of within the European Union,

this product should be treated and recycled in accordance with the laws of your jurisdiction

implementing the WEEE Directive.

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks of

NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to

change without notice. Other brand and product names are registered trademarks or trademarks of their

Regulatory Compliance

Certificate of Manufacture/Importer

It is hereby certified the NETGEAR model AGM731F and AGM732F has been

suppressed in accordance with the condition set out in MBPT-Amtsb|Vfg 243/1991

and vfg 46/1992. The operation of some equipment (for example, test transmitters)

in accordance with regulation may, however, be subject to certain restrictions.

Please refer to the note in the operating instructions. Federal Office for

Telecommunications Approvals has been notified of the placing of this equipment on

the market and has been granted the right to test the series for compliance with

regulation.

Note: This device has been tested and found to comply with limits for a Class B

digital device, pursuant to part 15 of FCC rules. These limits are designed to

provide reasonable protection against harmful interference in a commercial

installation.

EN 55 024 Declaration of Conformance

This is to certify that the NETGEAR Model AGM731F/AGM732F is shielded against

the generation of radio interference in accordance with the application of Council

Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN55

024 Class A (CISPR 22).

FCC Compliance Notice: Radio Frequency Interference

This device complies with part 15 of the FCC rules.

Operation is subject to the following conditions:

• This device may not cause harmful interference.

• This device must accept any interference received, including interference

that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause

harmful interference, in which case users will be required to take whatever

measures may be necessary to correct the interference at their own expense.

FCC Caution

• Any changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate this equipment.

• This device complies with Part 15 of the FCC Rules. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2)

this device must accept any interference received, including interference that may

cause undesired operation.

• For product available in the USA market, only channel 1~11 can be operated. Selection

of other channels is not possible.

• This device and its antenna(s) must not be co-located or operation in conjunction with

any other antenna or transmitter.

Class 1 LED product.

Because invisible laser radiation may be emitted

from the aperture of the port when no fiber cable is

connected, avoid exposure to laser radiation and do

not stare into open apertures.

Class 1 laser product.

Technical Support

Thank you for selecting NETGEAR products.

After installing your device, locate the serial number on the label of your product,

and use it to register your product at http://www.NETGEAR.com/register. Registration

is required to use the NETGEAR telephone support service. For product updates,

additional documentation, and support go to http://support.netgear.com.

For complete DoC go to the NETGEAR EU Declarations of Conformity website at

http://support.netgear.com/app/answers/detail/a_id/11621.

For GNU General Public License (GPL) related information, go to

http://support.netgear.com/app/answers/detail/a_id/2649.

WARNING!! Do not stack equipment, or place equipment in tight spaces, or in

drawers. Be sure your equipment is surrounded by at least 2 inches

of air space.

AGM731F-AGM732F IG 17Oct11.fm Page 2 Monday, October 17, 2011 11:54 AM

Produkt Specifikationer

Mærke:	Netgear
Kategori:	Ikke kategoriseret
Model:	AGM732F
Kabelteknologi:	1000Base-LX
Harmoniseret systemkode (HS):	85177900
Dataoverførselshastighed:	1 Gbit/sek.
Datalink-protokol:	Gigabit Ethernet