Netgear AirBridge WBC502B2 Manual

Netgear Wifi repeater AirBridge WBC502B2

Læs gratis den danske manual til Netgear AirBridge WBC502B2 (2 sider) i kategorien Wifi repeater. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Netgear AirBridge WBC502B2, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Power adapter and power cord

(varies by region).

Package contents

Pole mounting strap Wall mount screws

and anchors

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

Logo are trademarks of NETGEAR, Inc. Any

non‑NETGEAR trademarks are used for reference

purposes only.

April 2020

NETGEAR INTERNATIONAL LTD

Floor 1, Building 3,

University Technology Centre

Curraheen Road, Cork,

T12EF21, Ireland

Insight Instant

Wireless AirBridge

Model WBC502B2

Installation Guide

Insight Instant Wireless AirBridge

(Model WBC502)

This installation guide describes how to establish a WiFi bridge between two Insight

Instant Wireless AirBridge devices that are precongured for a point-to-point setup.

One AirBridge device is precongured as the master, the other one as the satellite.

You connect the AirBridge master to your wired network at the main site to provide

WiFi connectivity to the AirBridge satellite that you install at the detached site.

This point‑to‑point setup requires a line of sight between the AirBridge master at the

main site and the AirBridge satellite at the detached site.

AirBridge overview

1Power LED

2LAN1 LED: Power and network

3LAN2 LED: Ethernet device

4WLAN LED: WiFi connectivity

5Signal strength indicator LEDs

1. Prepare for installation

1Latch for bottom panel

Front view

Back view

1Reset button

2LAN1: PoE and network connectivity

3LAN2: Optional device for satellite only

Bottom view

1. Pull down on the latch on the front of the

device and remove the bottom panel of

the AirBridge to expose the ports.

2. Power on the AirBridge master

WARNING: Power on the AirBridge only with an Ethernet cable connected to the

provided power adapter, which must be placed indoors. Do not use any other

power source. The PoE port is not a standard PoE port. Using any other power

source can damage the device.

2. With the back of the AirBridge facing

you, connect an RJ‑45 Ethernet cable (not

provided) to the AirBridge 24V PoE port on

the right side of the device. Connect the

other end of the cable to the PoE port on

the power adapter.

3. Insert the plug into a power source.

All the LEDs light and then go off. The power LED stays lit.

Other AirBridge (WBC502) features:

• 2.4 GHz management SSID

• 5 GHz SSID extends your network

• Range of 1.8 miles (3 km) or more

This device must be professionally installed. It is

the installer’s responsibility to follow local country

regulations including operations within legal frequency

channels, output power and DFS requirements. Vendor

or Reseller or Distributor is not responsible for illegal

wireless operations. Please see Device’s Terms and

Conditions for more details.

1PoE port: Connect to AirBridge LAN1

2LAN port: Connect to the network

Installation guide

Screw placement guide

Model WBC502B2 is a bundle with one

precongured AirBridge master and

one precongured AirBridge satellite.

A label on the front of the AirBridge

shows whether the AirBridge is

precongured as a master or a satellite.

3. Connect the AirBridge master to the network

We recommend that you connect the AirBridge master to a network with Internet

access during setup. If the network includes a DHCP server, such as a router, the master

is automatically assigned a new IP address. (The default IP address is 192.168.0.100.)

1. Connect the LAN port on the power adapter to a LAN port on a switch or router

on your network. (Do connect the LAN2 port on the master directly to your not

network.)

2. Slide the bottom port cover onto the master until it latches.

3. Install the master to allow for a direct line of site to the detached location, facing

the location where you want to install the AirBridge satellite.

Master

Router Network

Power

adapter

Note: The power adapter and power

cord are not IP55 rated and must be

placed indoors. Because an Ethernet cable

supports a maximum length of 328 feet

(100 meters), you can place the AirBridge

outdoors but keep the power adapter and

power cord indoors.

Produkt Specifikationer

Mærke:	Netgear
Kategori:	Wifi repeater
Model:	AirBridge WBC502B2
Kode for international beskyttelse (IP):	IP55
Bredde:	186 mm
Dybde:	100 mm
Højde:	29 mm
Vægt:	504 g
Antal pr. pakke:	2 stk
Produktfarve:	Hvid
Produkttype:	Netværksbro
Wi-Fi:	Ja
Opbevaringstemperatur (T-T):	-40 - 80 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 90 %
Ethernet LAN-porte (RJ-45):	2
Ethernet LAN:	Ja
Driftstemperatur (T-T):	-20 - 60 °C
Ethernet LAN-datahastigheder:	10,100,1000 Mbit/s
Forbindelsesteknologi:	Kabel & trådløs
Certificering:	FCC / ISED, CE
Strømforbrug (maks.):	8.93 W
Bedste Wi-Fi standard:	Wi-Fi 5 (802.11ac)
WLAN dataoverførselshastighed (maks):	867 Mbit/s
Ethernet LAN-grænsefladetype:	Gigabit Ethernet
Antennedesign:	Intern
Antenner, antal:	1
Knap til nulstilling:	Ja
LED-indikatorer:	Ja
Kan monteres på væggen:	Ja
Strømkilde type:	PoE
Maksimal dataoverførselshastighed:	867 Mbit/s
Modulation:	16-QAM, 64-QAM, 256-QAM, BPSK, QPSK
Maksimal overførselsafstand:	3000 m
Strøm over Ethernet (PoE):	Ja
Niveau for antennestyrke (maks.):	14 dBi
Signalstyrke:	23 dBm
Understøttede dataoverførselshastigheder:	802.11a: 6, 9, 12, 18, 24, 36, 48, 54 802.11n: 6.5 to 300 (MCS0 to MCS15) 802.11ac: 6.5 to 867 (MCS0 to MCS9, NSS=1 to 2)
Beskyttelse ved overspænding:	Ja
Power over Ethernet (PoE) spænding:	24 V