Netgear APS600Wv3 Manual

Netgear Ikke kategoriseret APS600Wv3

Læs gratis den danske manual til Netgear APS600Wv3 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Netgear APS600Wv3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Installation Guide

Overview

The APS600Wv3, APS1200Wv2, and APS2000Wv2 auxiliary power supplies (APS) are

supported in the following M4350 series switch models:

• M4350-24X8F8V (SKU: XSM4340V)

• M4350-36X4V (SKU: XSM4340CV)

• M4350-32F8V (SKU: XSM4340FV)

• M4350-16V4C (SKU: VSM4320C)

• M4350-40X4C (SKU: XSM4344C)

Each APS has an LED that indicates the power supply status, as described in the following

table.

LED Status

Solid green DC output is present and voltage is good.

Off Loss of AC power occurred or AC power is not present.

Blinking green AC power is present but DC output is for standby only.

Blinking

amber

Warnings for abnormal events, like high operating temperature, high

output current, slow fan, high output power.

Solid amber A power supply failure occurred and the APS will be shut down.

Install an APS

In models with more than one power supply bay, you can install an additional APS.

1. Pull out the cover plate from the power module bay in which you want to insert the

additional APS.

2. Insert the APS into the power module bay, and gently push the APS into the bay.

CAUTION: When inserting the APS, do not use unnecessary force. Doing so

can damage the connectors on the back of the APS and on the midplane.

3. Connect the end of the power cord to the power receptacle on the APS.

4. Plug the AC power cord into a power source such as a wall socket or power strip.

Auxiliary Power Supplies for the

M4350 Series Fully Managed Switches

APS600Wv3, APS1200Wv2, and APS2000Wv2

Package contents

• Auxiliary power supply

• Power cord (varies by region)

• Installation guide

Replace an APS

In models with more than one APS, the APSs are hot-pluggable.

1. If your switch functions with a single APS only, disconnect the power cord from the

APS and let the switch power down.

If your switch functions with more than one APS, you do not need to power down the

switch and you can perform a hot swap.

2. Remove the APS from the power module bay by doing the following:

a. Position the extraction handle perpendicular to the APS.

b. Insert your left index nger into the extraction handle.

c. Use your left thumb to move the orange release latch to the left and keep it in the

release position.

d. Pull the extraction handle.

We recommend that you use your right hand to support the APS.

3. Insert the replacement APS into the power module bay, and gently push the APS into

the bay until the latch locks.

CAUTION: When inserting the APS, do not use unnecessary force. Doing so

can damage the connectors on the back of the APS and on the midplane.

4. Connect the end of the power cord to the power receptacle on the APS.

When you apply power, the LED on the APS lights. The LED on the switch for the

power supply bay also lights. If these LEDs do not light, make sure that the power

cord is plugged in and that the power source is good.

November 2023

NETGEAR Logo are trademarks of

NETGEAR, Inc. Any non‑NETGEAR

trademarks are used for reference

purposes only.

NETGEAR, Inc.

350 East Plumeria Drive

San Jose, CA 95134, USA

NETGEAR INTERNATIONAL LTD

Floor 6, Penrose Two,

Penrose Dock, Cork, T23 YY09, Ireland

Technical specications

Feature APS Model Specications

AC input APS600Wv3 100-120VAC, 8.5A, 50-60 Hz

200-240VAC, 4.5A, 50-60 Hz

APS1200Wv2 100-120VAC, 12A, 50-60 Hz

200-240VAC, 10A, 50-60 Hz

APS2000Wv2 100-120VAC, 12A, 50-60 Hz

200-240VAC, 10A, 50-60 Hz

DC output APS600Wv3 +54.5VDC, 11.01A @ 90-132 VAC

+54.5VDC, 11.01A @ 180-200VAC

+54.5VDC, 11.01A @ 200-264VAC

APS1200Wv2 +54.5VDC, 18.69A @ 90-132 VAC

+54.5VDC, 22.43A @ 180-264 VAC

APS2000Wv2 +54.5VDC, 18.69A, @ 90-132 VAC

+54.5VDC, 33.64A, @ 180-198 VAC

+54.5VDC, 37.38A, @ 198-264 VAC

Dimensions (H x W x D) All models 1.6 x 2.9 x 7.3 in (40 x 73.5 x 185 mm)

Operating temperature APS600Wv3 32°F to 131°F (0°C to 55°C )

APS1200Wv2 32°F to 131°F (0°C to 55°C )

APS2000Wv2 32°F to 122°F (0°C to 50°C )

Operating relative humidity All models 5% to 85% relative humidity

Operating altitude level All models Up to 16,404 feet (5,000 m)

Storage temperature APS600Wv3 –40°F to 176°F (–40°C to 80°C )

APS1200Wv2 –40°F to 185°F (–40°C to 85°C )

APS2000Wv2 –40°F to 176°F (–40°C to 80°C )

Storage altitude level All models Up to 49,859 feet (15,200 m)

Feature APS Model Specications

MTBF All models Minimum MTBF at continuous

operation of 250,000 hours, input

voltage of 230VAC, inlet temperature

of 104°F (40°C), and output load

of 80%, as calculated by Bellcore

Telcordia SR-332-Issue 2

Compliance - Safety All models CSA

RCM

CCC/CQC

BIS

BSMI

Compliance - EMC All models FCC

ICES-003

VCCI

RCM

CCC/CQC

BSMI

Warranty

Visit the NETGEAR warranty page to view the warranty information for your new NETGEAR

device:

Support and Community

Visit netgear.com/support to get your questions answered and access the latest

downloads.

You can also check out our NETGEAR Community for helpful advice at

community.netgear.com.

Regulatory and Legal

Si ce produit est vendu au Canada, vous pouvez accéder à ce document en français

canadien à netgear.com/support/download/. (If this product is sold in Canada, you

can access this document in Canadian French at netgear.com/support/download/.)

For regulatory compliance information including the EU Declaration of Conformity,

visit netgear.com/about/regulatory/. See the regulatory compliance document before

connecting the power supply. For NETGEAR’s Privacy Policy, visit

netgear.com/about/privacy-policy. By using this device, you are agreeing to NETGEAR’s

Terms and Conditions at netgear.com/about/terms-and-conditions. If you do not agree,

return the device to your place of purchase within your return period.

Do not use this device outdoors. If you connect cables or devices that are outdoors to the

switch, see kb.netgear.com/000057103 for safety and warranty information.

Applicable to 6 GHz devices only: Only use the device indoors. The operation of 6 GHz

devices is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation

of this device is permitted in large aircraft while ying above 10,000 feet. Operation of

transmitters in the 5.925-7.125 GHz band is prohibited for control of or communications

with unmanned aircraft systems.

Australia:

www.netgear.com/au/

about/warranty/

Japan:

www.netgear.com/jp/

about/warranty/

China:

www.netgear.com/cn/

about/warranty/

All other countries: Visit

www.netgear.com/about/

warranty/

and click the ag to select

your country.

http://support.netgear.cn/China-RoHS

Produkt Specifikationer

Mærke:	Netgear
Kategori:	Ikke kategoriseret
Model:	APS600Wv3

Har du brug for hjælp?

Hvis du har brug for hjælp til Netgear APS600Wv3 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Netgear Manualer

Netgear Nighthawk A9000 Manual

25 Juli 2025

Netgear PL1000-100PES Manual

9 Juli 2025

Netgear M4300-24X24F Manual

7 Juli 2025

Netgear APS1000W Manual

26 Juni 2025

Netgear GS116v3 Manual

17 Juni 2025

Netgear GS728TXUPv3 Manual

17 Juni 2025

Netgear GS108EPP Manual

7 Juni 2025

Netgear GS105EPP Manual

7 Juni 2025

Netgear GS105EP Manual

7 Juni 2025

Netgear GS108EP Manual

6 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech EAI-3100 Manual

30 Juli 2025

Deye SUN-M180G4-EU-Q0-I Manual

30 Juli 2025

Crestron STIRP Manual

30 Juli 2025

Intellinet 790741 Manual

30 Juli 2025

Saris Edge 2-Bike Manual

30 Juli 2025

Advantech ROM-3310 Manual

30 Juli 2025

Advantech EKI-1751I Manual

30 Juli 2025

Advantech ICR-1601W Manual

30 Juli 2025

C2G 29341 Manual

30 Juli 2025

Advantech ITA-8120 Manual

30 Juli 2025