Netgear GS316P Manual

Netgear Ikke kategoriseret GS316P

Læs gratis den danske manual til Netgear GS316P (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 64 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 32.5 anmeldelser. Har du et spørgsmål om Netgear GS316P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

are trademarks of NETGEAR, Inc. Any non‑NETGEAR

trademarks are used for reference purposes only.

Installation Guide

1. Search for NETGEAR Insight and download the latest app.

2. Set up a NETGEAR account if you do not have one.

3. Tap the menu in the upper-left corner.

4. Tap REGISTER ANY NETGEAR DEVICE.

5. Enter the serial number located on the bottom of the switch, or use the

camera on your mobile device to scan the serial number bar code.

6. Tap .GO

The switch is registered and added to your account. You can now view the

switch in the NETGEAR Insight app.

Note: Because this is an unmanaged switch, you cannot congure or manage it

in NETGEAR Insight.

Connect the switch

1. Connect network devices to the ports on the switch.

2. Connect an RJ-45 port on the switch to a network.

Note: In a small ofce or home ofce network, connect the switch to the LAN

port of a router that, in turn, is connected to an Internet modem.

3. Power on the switch.

PoE considerations

The switch prioritizes the PoE+ power that it supplies in ascending port order

(from port 1 to port 16). If the aggregate power requirements of all attached

power devices (PD) exceed the power budget of the switch, the PD on the

highest-numbered port is disabled to make sure that the PDs that are connected

to the higher-priority, lower-numbered ports are supported rst.

The following tables describe the power adapter models that are compatible with

the GS316P and GS316PP switches and their PoE classes and switch allocations:

Note: The listed total power budget is the maximum power limit for the

switch. Many PDs require less than maximum power, so the aggregate power

requirements are lower than the maximum, allowing all sixteen PoE ports to be

active simultaneously.

Power adapters and total power budgets for the GS316P and GS316PP:

Power adapter model Power adapter Total power budget

EPS90W 90W 76W

EPS130W 130W 115W

EPS200W 200W 183W

PoE classes and switch allocations:

Device

class

Standard Class

description

Minimum power

allocated to the

powered device

Range of power

delivered to the

powered device

0 PoE and PoE+ Default power

(full)

0.44W 0.44W–12.95W

Device

class

Standard Class

description

Minimum power

allocated to the

powered device

Range of power

delivered to the

powered device

1 PoE and PoE+ Very low

power

4.0W 0.44W–3.84W

2 PoE and PoE+ 7.0W 3.84W–6.49WLow power

3 PoE and PoE+ Mid power 15.4W 6.49W–12.95W

4 PoE+ only High power 30.0W 12.95W–25.5W

PoE troubleshooting

Here are some tips for correcting PoE problems that might occur:

• Make sure that the PoE Max LED is off. If the PoE Max LED is solid yellow,

disconnect one or more PoE devices to prevent PoE oversubscription. Start by

disconnecting the device from the highest-numbered port.

• Make sure that the Ethernet cables are plugged in correctly. For each

powered device (PD) that is connected to the switch, the corresponding right

port LED on the switch lights solid green. If the right port LED lights solid

yellow, a PoE fault occurred and PoE halted because of one of the conditions

that are listed in the following table.

PoE Fault Condition Possible Solution

A PoE-related short circuit occurred on the

port.

The problem is most likely with the attached

PD. Check the condition of the PD or restart the

PD by disconnecting and reconnecting the PD.

The PoE power demand of the PD exceeded

the maximum level that the switch permits,

which is 30.9W.

The PoE current on the port exceeded the

classication limit of the PD.

The PoE voltage of the port is outside the

range that the switch permits.

Restart the switch to see if the condition

resolves itself.

16-port Gigabit Ethernet Unmanaged

High-Power PoE+ Switch with FlexPoE

Models GS316P and GS316PP

Package contents

• Switch

• Power cord (varies by region)

• Power Adapter (130W for GS316P/200W for GS316PP)

• Wall installation kit

• Rubber feet

• Mounting ties (for power adapter)

• Rack-mount kit for rack installation

• Installation guide October 2019

Sample connections

PoE VoIP

Phone

Wave 2

Wireless AP

PoE+ security

camera

Router

GS316PP

Internet

Laptop

Smart

phone

Internet

PoE+

Produkt Specifikationer

Mærke:	Netgear
Kategori:	Ikke kategoriseret
Model:	GS316P
Bredde:	286 mm
Dybde:	102 mm
Højde:	27 mm
Vægt:	880 g
Produktfarve:	Sort
Opbevaringstemperatur (T-T):	-20 - 70 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Driftstemperatur (T-T):	0 - 40 °C
Husmateriale:	Metal
Strømforbrug (maks.):	127.9 W
Netværksstandarder:	IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3az, IEEE 802.3i, IEEE 802.3u, IEEE 802.3x
Servicekvalitet support (QoS):	Ja
LED-indikatorer:	Ja
Kan monteres på væggen:	Ja
Harmoniseret systemkode (HS):	85176990
Driftshøjde:	0 - 3000 m
DC indgangsspænding:	54 V
Indgangsstrøm:	2.4 A
Fuld duplex:	Ja
Strøm over Ethernet (PoE):	Ja
Gennemsnitstid mellem fejl (MTBF):	2362192 t
Switch-type:	Ikke administreret
Power over Ethernet plus (PoE+) porte, antal:	16
10G understøttelse:	Ingen
Auto MDI/MDI-X:	Ja
Flowkontrol support:	Ja
Basis omskiftning RJ-45 Ethernet porte, antal:	16
Basis omskiftning RJ-45 Ethernet porttype:	Gigabit Ethernet (10/100/1000)
MAC adresselabel:	4000 entries
Switch kapacitet:	32 Gbit/sek.
Jumbo Frames support:	Ja
Jumbo rammer:	9216
Stativ-montering:	Ingen
Varmeafgivelse:	437.42 BUT/t
Strømstik:	DC-in-stik
Pakke bufferlager:	1 MB
Latens (1 Gbps):	3.7 µs
Pakke videresendelsesrate (1 Gbps):	1448000 pps