Netgear RPS4000v2 Manual

Netgear Ikke kategoriseret RPS4000v2

Læs gratis den danske manual til Netgear RPS4000v2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Netgear RPS4000v2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Installation Guide
Check the LEDs
Power system indicators are listed in the following table:
Label Color Activity Description
PWR
(Power)
Green On Power is being provided to the RPS4000v2.
Power
Module
Status
Green On An APS1000W is present and working properly.
Yellow On An APS1000W is present but is not working
properly.
Off Off There is no APS1000W present.
RPS Port
Status
Green On The switch supports dynamic power allocation, and
the APS1000W in the corresponding RPS port and
power module bay is supplying power to the switch.
Blinking The switch supports dynamic power allocation, but
the APS1000W in the corresponding RPS port and
power module bay is not supplying power to the
switch. Power is being supplied by the APS1000W in
a different power module bay.
Yellow On The switch does not support dynamic power
allocation, and the APS1000W is providing power to
the switch.
Blinking The switch does not support dynamic power
allocation, but the APS1000W is not supplying
power to the switch.
Off Off No power is being supplied to the switch, or the
switch is not recognized.
Redundant Power System and Power Bank
Model RPS4000v2
The Redundant Power System and Power Bank RPS4000v2 provides power
system redundancy to external devices such as NETGEAR chassis switches,
managed switches, or smart switches with an RPS capability.
Each RPS4000v2 includes four power module bays, and can provide a maximum
output of 4000W when four APS1000W power supply units (PSU) are installed.
The RPS4000v2 can supply power to devices that support dynamic power
allocation as well as to legacy devices. The RPS4000v2 acts as a redundant power
system in 12 VDC context and acts as a power bank in PoE (56 VDC) context.
Package Contents
This package includes:
• Redundant Power System and Power Bank RPS4000v2
• AC power cable
• RPS cable, 60 cm (23.6 in.),16 pin
RPS ports
Each RPS port on the RPS4000v2 can provide a maximum of 1440W at 56 VDC
and 200W at 11 VDC. Output power depends on the number of power supply
units (PSU) installed, and the settings of the Type selector and Current Share (CS)
selector on the back panel of the RPS4000v2.
To determine the RPS type for other switches, see the hardware installation guide
,which you can download by visiting netgear.com/support/download/.
Install the RPS4000v2
Install the RPS4000v2 in a standard 19-inch rack.
WARNING: Do not stack equipment, or place equipment in tight spaces or in
drawers. Be sure that your equipment is surrounded by at least 2 inches (5 cm) of
air space.
Insert a power supply unit
In models with more than one PSU, the PSUs are hot-pluggable.
1. If your switch functions with a single PSU only, disconnect the power cord
from the PSU and let the switch power down.
If your switch functions with more than one PSU, you do not need to power
down the switch and you can perform a hot swap.
2. Remove the PSU from the power module bay by moving the orange release
latch to the left and pulling the extraction handle.
3. Insert the replacement PSU into the power module bay, and gently push the
PSU into the bay until the latch locks.
CAUTION: When inserting the PSU, do not use unnecessary force. Doing so
can damage the connectors on the back of the PSU and on the midplane.
4. Connect the end of the power cord to the power receptacle on the PSU.

Produkt Specifikationer

Mærke: Netgear
Kategori: Ikke kategoriseret
Model: RPS4000v2

Har du brug for hjælp?

Hvis du har brug for hjælp til Netgear RPS4000v2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Netgear Manualer

Netgear

Netgear Orbi RBE373 Manual

23 September 2025
Netgear

Netgear Orbi RBE374 Manual

23 September 2025
Netgear

Netgear Orbi RBE370 Manual

23 September 2025
Netgear

Netgear Orbi RBE372 Manual

23 September 2025
Netgear

Netgear GS748Tv6 Manual

24 August 2025
Netgear

Netgear GS752TSB Manual

23 August 2025
Netgear

Netgear GS728TPSB Manual

22 August 2025
Netgear

Netgear Orbi RBK864S Manual

21 August 2025
Netgear

Netgear Orbi RBE973S Manual

21 August 2025
Netgear

Netgear Orbi RBK854 Manual

21 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Dahua Technology

Dahua Technology EVS7124D Manual

27 Oktober 2025
Dahua Technology

Dahua Technology XVR7816S-4KL-X-LP Manual

27 Oktober 2025
Dahua Technology

Dahua Technology HAC-HDW1220EM Manual

27 Oktober 2025
Dahua Technology

Dahua Technology ISC-M6550 Manual

27 Oktober 2025
Dahua Technology

Dahua Technology EVS7148D Manual

27 Oktober 2025
Dahua Technology

Dahua Technology HAC-HFW2249E-A Manual

27 Oktober 2025
Dahua Technology

Dahua Technology XVR5108/16H-X Manual

27 Oktober 2025
Dahua Technology

Dahua Technology XVR5108HE-4KL-I2 Manual

27 Oktober 2025
Dahua Technology

Dahua Technology XVR7104HE-4KL-I Manual

26 Oktober 2025
Dahua Technology

Dahua Technology NVR4816-4KS2 Manual

26 Oktober 2025