Netgear SRX5308 Manual

Netgear Ikke kategoriseret SRX5308

Læs gratis den danske manual til Netgear SRX5308 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Netgear SRX5308, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

)NSTALLATION'UIDE

ProSafe® Gigabit Quad WAN SSL VPN Firewall SRX5308

Start Here

Follow these instructions to set up your VPN firewall. You can also consult the

online Reference Manual http:// or the NETGEAR Knowledge base at

kbserver.netgear.com. A link to the online Reference Manual is on the ProSafe

® Gigabit

Quad WAN SSL VPN Firewall SRX5308 Resource CD.

Prepare to Install Your Firewall

This guide provides instructions for setting up a simple dual WAN port rollover

configuration. Refer to the Reference Manual for other WAN port configuration options.

First, Connect the SRX5308

1. Connect the cables between the SRX5308, two modems, and a computer

a. Turn off unplug the broadband modems.and

b. Insert an Ethernet cable from a modem into the WAN1 port of the SRX5308.

c. Insert an Ethernet cable from the other modem into the WAN2 port of the

SRX5308.

d. Insert the Ethernet cable that came with your VPN firewall into a LAN port on

the firewall and insert the other end into the Ethernet port of your computer.

Your network cables are connected and you are ready to restart your network.

2. Restart your network in the correct sequence

2 41 3 5

Warning: Failure to restart your network in the correct sequence could prevent you

from connecting to the Internet.

a. First, power on the broadband modems. Wait approximately 2 minutes until they

power up.

b. Now, power on the SRX5308.

c. Last, turn on your computer.

d. Before configuring your SRX5308, check the status lights to verify the

following:

1 - Power (green). The power light should turn solid green. If it does not turn

solid green, see the Troubleshooting section of the full manual.

2 -Test (amber). When you first turn on the router, the amber test light will be lit

for approximately 2 minutes. If it is still on after several minutes, see the

Troubleshooting Tips below.

3 - LAN (green/amber). Each port has a green light on the left side of the port. If

on the port has a link, if it blinks, the port is active. Each port has a green and

amber light on the right side of the port. If the green light is on, the port is

1000Mbps, if the amber light is on, the port is 100Mbps, if neither light is on, the

port is 10Mbps. If a LAN light is not lit, ensure that its Ethernet cable is securely

attached at both ends, and that the computer is turned on.

4 - WAN (green/amber). Each port has a green light on the left side of the port

and a green and amber light on the right side of the port. The lights operate the

same as the LAN lights described above.

5 - DMZ (green): If this light is on, the port is configured as a DMZ port.

Next, Configure the SRX5308 for Internet Access

Before you begin, be sure you have the configuration parameters from your ISP handy.

1. Log in to the firewall

a. Use a browser to connect to https://192.168.1.1

Note: To connect to the firewall, your computer needs to be configured to obtain an IP

address automatically via DHCP. If you need instructions on how to do this, please refer to

the online reference manual. A link to the manual is on your ProSafe

® Gigabit Quad WAN

SSL VPN Firewall SRX5308 Resource CD.

b. For security reasons, the

firewall has its own user name

and password.

When prompted, enter admin

for the firewall User Name and

password for the firewall Pass-

word.

c. Click You are now connected to the firewall. Login.

The Web Support tab on the main menu contains links to the online NETGEAR

SRX5308 product documentation and support Knowledge base. Be aware that

the default login time-out is 5 minutes of inactivity, after which automatic logout

will occur.

d. Click , Network Configuration WAN Settings WAN . The screen will display.

A table of settings for the WAN ports is shown.

2. Connect to the Internet

a. Click on the Edit button at the right of the WAN1 row. The WAN1 ISP Settings

screen will be displayed. Click Auto Detect WAN1 ISPat the bottom of the

Settings screen. The firewall will automatically attempt to detect your

connection type. If you know your ISP connection type, you can manually

configure the firewall settings on the WAN1 ISP screen. If connecting manually,

click Apply to save your settings.

b. When finished, click Test to verify that the Internet connection is active.

c. Select the WAN2 ISP tab and complete the same steps you completed in steps a

and b.

SRX5308_IG.fm Page 1 Friday, December 14, 2012 12:37 PM

December 2012

NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered trademarks

of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other countries. Information is subject to

change without notice. Other brand and product names are registered trademarks or trademarks of their

Intended for indoor use only in all EU member states, EFTA states, and Switzerland.

Now, Configure WAN Rollover Mode

The WAN ports of the firewall can be configured for either rollover for increased system

reliability or load balancing for maximum bandwidth efficiency. The rollover option is

presented here. Refer to the manual for instructions on configuring the load balancing

mode.

In rollover mode, expect the following:

• You designate one WAN port as primary and the other as the rollover link.

• While the primary link is up, all traffic goes over the primary WAN port. If the

primary link goes down, traffic is sent over the rollover link.

• Traffic will automatically roll back to the primary link once it is back up.

To configure the dual WAN ports for rollover:

1. Select WAN Mode WAN Mode from the sub-menu. The screen will display.

2. From the Auto-Rollover pull-down menu, select which WAN port will be primary.

3. WAN failure is detected using DNS queries to the DNS server or PING messages to

an IP address. If the replies are not received, the WAN interface is considered down.

Fill in the appropriate fields:

• Configured DNS Servers – In this case, DNS queries are sent to the ISP DNS

servers configured on the WAN ISP pages.

• Using this DNS Server – In this case, DNS queries are sent to a specified DNS

Server.

• Ping to this IP address – In this case, PING queries are sent to the specified IP

address.

• Test Period – a DNS or PING query is sent after every test period. The minimum

test period is 30 seconds.

• Failover after – The WAN link is considered down after the configured number

of queries fail to get a reply. The minimum number of failed queries is four. The

rollover link is brought up after this.

4. Click Apply to save your changes.

Troubleshooting Tips

Here are some tips for correcting common problems you may encounter.

Be sure to restart your network in this sequence:

1. Turn off and unplug the modems, turn off the SRX5308, and shut down the computer.

2. Plug in and turn on the modems. Wait for the modems to power up (approximately 2

minutes).

3. Turn on the SRX5308. Wait until the amber test light goes out.

4. Turn on the computer.

Make sure the Ethernet cables are securely plugged in.

• The WAN Link/Act light on the VPN firewall will be lit if the Ethernet cable to the

VPN firewall from each modem is plugged in securely and the modems and VPN

firewall are turned on.

• For each powered on computer connected to the VPN firewall with a securely

plugged in Ethernet cable, the corresponding VPN firewall LAN port status light

should be lit. The front of the SRX5308 identifies the number of each LAN port.

Make sure the network settings of the computer are correct.

Computers be configured to obtain IP DNS addresses automatically via DHCP. must and

For help with this, please see the online Reference Manual; a link to the manual is on the

ProSafe® Gigabit Quad WAN SSL VPN Firewall SRX5308 Resource CD.

For Cable Modem connections, use MAC spoofing.

Some cable modem ISPs require that you use the MAC address of the computer registered

on the account. If so, in the Router’s MAC Address section (accessed through the

Advanced WAN1 ISP Settings link on the screen), select either “Use this Computer’s

MAC” or “Use this MAC address” and enter the appropriate MAC address. The firewall

will then capture and use the MAC address of the computer that you identified. You must

select the computer that is registered with the ISP. Click Apply to save your settings.

Restart the network in the correct sequence.

Use the SRX5308 status lights to verify correct operation.

If the SRX5308 Test light does not go out approximately 2 minutes after turning the

firewall on, reset the fiewall as described in the Reference Manual.

Technical Support

After installing your device, locate the serial number on the label of your product and use

it to register your product at https://my.netgear.com.

You must register your product before you can use NETGEAR telephone support.

NETGEAR recommends registering your product through the NETGEAR website.

For product updates and web support, visit http://support.netgear.com.

NETGEAR recommends that you use only the official NETGEAR support resources.

You can get the reference manual online at http://downloadcenter.netgear.com or through

a link in the product’s user interface.

For the current EU Declaration of Conformity, visit

http://support.netgear.com/app/answers/detail/a_id/11621/.

SRX5308_IG.fm Page 2 Friday, December 14, 2012 12:37 PM

Produkt Specifikationer

Mærke:	Netgear
Kategori:	Ikke kategoriseret
Model:	SRX5308

Har du brug for hjælp?

Hvis du har brug for hjælp til Netgear SRX5308 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Netgear Manualer

Netgear GS748Tv6 Manual

24 August 2025

Netgear GS752TSB Manual

23 August 2025

Netgear GS728TPSB Manual

22 August 2025

Netgear Orbi RBK864S Manual

21 August 2025

Netgear Orbi RBE973S Manual

21 August 2025

Netgear Orbi RBK854 Manual

21 August 2025

Netgear Orbi RBKWM Manual

21 August 2025

Netgear Orbi RBE973SB Manual

21 August 2025

Netgear Orbi RBS860 Manual

20 August 2025

Netgear Orbi RBK866SB Manual

20 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Osram VX250-SP Manual

13 September 2025

Vello CB-800 Manual

13 September 2025

Ibm System Storage ProtecTIER TS7620 Manual

13 September 2025

Ibm System Storage N6250 Manual

13 September 2025

Avanti FF1013D3S Manual

13 September 2025

Anybus ProfiHub B2FO2+ Manual

13 September 2025

Liebherr CNsdh 762i Manual

12 September 2025

Urbanista Palo Alto Manual

12 September 2025

Autel MaxiSYS MS908S Pro Manual

12 September 2025

Parisot Biotiful 2273A3PT Manual

12 September 2025