Nexa MYCR-250 Manual

Nexa Ikke kategoriseret MYCR-250

Læs gratis den danske manual til Nexa MYCR-250 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Nexa MYCR-250, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Safety and information

Indoor range: up to 30 m (optimal conditions). The range is

strongly dependent on local conditions, such as the presence

of metals. For example, the thin metal coating in Low-emissivity

(Low-E) glass has a negative impact on the range of radio signals.

There may be restrictions on the use of this device outside the

EU. If applicable, check whether this device complies with local

directives.

Maximum load: Never connect lights or equipment that exceed

the maximum load of the receiver, as it can result in defects, a

short circuit or ﬁre.

Life-support: Never use Nexa products for life-support systems

or other applications in which equipment malfunctions can have

life-threatening consequences.

Interference: All wireless devices may be subject to interference,

which could affect performance. The minimum distance between

2 receivers should be at least 50 cm.

Repairing: Do not attempt to repair this product. There are no

user-serviceable parts inside.

Water-resistance: This product is not water-resistant. Keep it dry.

Moisture will corrode the inner electronics and can result in a short

circuit, defects and shock hazard.

Cleaning: Use a dry cloth to clean this product. Do not use harsh

chemicals, cleaning solvents, or strong detergents.

Environment: Do not expose the product to excessive heat or

cold, as it can damage or shorten the life of electronic circuit

boards.

ENGLISH

Plug-in receiver with on/off button on the receiver. Works with

System Nexa remote controls, transmitters and the Nexa Bridge.

This is a self-training system, so installation is very easy and ﬂexible.

INSTALLATION

Connect the load to the receiver. Make sure that the load does not

exceed the output speciﬁed under “Dimmer settings” in the table.

PROGRAMMING

1. Connect the receiver (plug-in) to a power socket. The receiver

goes into setup mode as soon as it is powered up.

2. Press the “ON” button for the selected channel on any System

Nexa remote control within 6 seconds.

PROGRAMMING CONFIRMATION

The LED indicator on the receiver ﬂashes rapidly. If a light is

connected to the receiver, this ﬂashes twice.

DELETING MEMORY

1. To delete a memory slot, remove the receiver (plug-in) from the

wall socket

2. Wait at least 6 seconds

3. Reconnect the receiver to a wall socket

4. Press the “OFF” button for the selected channel on the System

Nexa remote control within 6 seconds.

To delete all storage locations, repeat steps 1-3 above, then press

the “ALL OFF” button on the System Nexa control within 6 seconds.

CONFIRMATION OF DELETION

The LED indicator on the receiver ﬂashes rapidly. If a light is

connected to the receiver, this ﬂashes twice.

MEMORY SLOTS

Every MYCR-3500 plug-in receiver has 32 memory slots. When

memory slot 32 is occupied, slot 1 is overwritten during setup.

CONTROL

The plug-in receiver can be controlled in a number of ways.

1. With a System Nexa remote control

2. With other programmed System Nexa transmitters

3. With the On/Off button on the plug-in receiver

4. With a Nexa Bridge

DIMMER SETTINGS

MYCR-250 is supplied set for leading edge dimming and can be set

to trailing edge dimming.

Selection of an appropriate setting is dependent on the type of

load to be connected – see the table below. Contact the place of

purchase for your luminaire/light if you are not sure what type of

load is to be set.

LOAD SETTING OUTPUT

Halogen lamps and bulbs Trailing edge 25-250W /220-240V W RL

Electronic transformers Trailing edge 20-250W / 220-240V

Dimmable LED and

low-energy bulbs Trailing edge 3-120W / 220-240V

Conventional transformers Leading edge 40-250W / 220-240V

SWITCH BETWEEN LEADING EDGE AND TRAILING EDGE

DIMMING

1. Switch on the connected charge using the ON/OFF button on the

receiver.

2. Press and hold down the ON/OFF button on the receiver for 10

seconds.

3. The LED indicator on the receiver ﬂashes in series of 4.

4. Brieﬂy press the ON/OFF button to toggle between leading edge

and trailing edge dimming.

5. The LED indicator on the receiver ﬂashes quickly and the

connected (light) ﬂashes twice and then dims to the set minimum

level in order to conﬁrm the new setting.

The LED indicator shows the set dimming method every time MYCR-

250 is switched on or off using the ON/OFF button.

LED ﬂashes once = Leading edge dimming

LED ﬂashes twice = Trailing edge dimming

SETTING THE MINIMUM DIMMER LEVEL

1. Switch on the connected charge using the ON/OFF button on the

receiver.

2. Press and hold down the ON/OFF button on the receiver for

3 seconds.

3. The LED indicator on the receiver ﬂashes in series of 2.

4. Use a programmed remote control to adjust the minimum dimmer

level. ON increases the level by one step, OFF decreases the level by

one step (4 steps in total).

5. Brieﬂy press the ON/OFF button to save the minimum dimmer level set.

6. The LED indicator on the receiver ﬂashes quickly and the connected

(light) ﬂashes twice and then dims to the set minimum level in order

to conﬁrm the new setting.

Note: MYCR-250 is a universal type dimmer. To avoid damage to the

receiver it has to be set up for the type of load that is connected to it,

see ”Dimmer settings” for more information.

THIS PRODUCT SUPPORTS SMART MODE.

Devices that support Smart Mode can save up to 3 different

favourite scenarios, and these can be activated easily using a

Nexa Smart Mode transmitter.

PÅ/AV-knapp

och LED

ON/OFF button

and LED

NEXA AB, DATAVÄGEN 37B, 436 32 ASKIM, SWEDEN

info@nexa.se | www.nexa.se

MYCR-250

PLUG-IN DIMMER

TECHNICAL DATA

Declaration of conformity is available at www.nexa.se

MYCR-250

Power supply 220-240 V~50 Hz

Max. load 20–250 W R/RC / 40–250 W RL / 1.1A

Max. load LED 3–120 W LED

Frequency System Nexa (433,92 MHz)

Range upp till 30 m

Memory slots 32

Power consumption < 1 W (standby)

Built in protective device Temperature fuse

IP rating Inomhusbruk / Indoor use

Size 53 x 53 x 58 mm

Produkt Specifikationer

Mærke:	Nexa
Kategori:	Ikke kategoriseret
Model:	MYCR-250

Har du brug for hjælp?

Hvis du har brug for hjælp til Nexa MYCR-250 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Nexa Manualer

Nexa Bridge X Manual

23 September 2024

Nexa MGDR-3500/SET Manual

23 September 2024

23 September 2024

23 September 2024

1 September 2024

1 September 2024

1 September 2024

1 September 2024

1 September 2024

1 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Tripp Lite U339-001-FLAT Manual

31 Juli 2025

Tripp Lite IBLOK2-0 Manual

31 Juli 2025

Tripp Lite TR-6FM Manual

31 Juli 2025

L.R.Baggs Element Active System Manual

31 Juli 2025

Tripp Lite Protect It! TLP310USBCW Manual

31 Juli 2025

Tripp Lite PR25 Manual

31 Juli 2025

SolidDrive SD-1G Manual

31 Juli 2025

Tripp Lite PR7 Manual

30 Juli 2025

Wren & Cuff 70's Your Face Fuzz Manual

30 Juli 2025

Advantech WISE-2211 Manual

30 Juli 2025