On-Q lyriQ Manual

On-Q Hi-Fi system lyriQ

Læs gratis den danske manual til On-Q lyriQ (9 sider) i kategorien Hi-Fi system. Denne vejledning er vurderet som hjælpsom af 74 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 37.5 anmeldelser. Har du et spørgsmål om On-Q lyriQ, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 1 of 9

INSTRUCTION/INSTALLATION SHEET

lyriQ™ High Performance Keypad

IS-0369 REV. E



1. Introduction

The lyriQ™ High Performance Keypad, P/N AU1000-xx (see Figure 1), is an

integral part of the lyriQ™ Multi-Room Audio System. It is a component which,

when combined with other essential components ( a Source Input Unit,

Distribution Module and Speakers) and your source equipment (receiver, CD

player, etc.), creates a versatile whole-house audio system that will fill your

rooms with high-quality sound for years to come. It uses Category 5 wiring to

distribute audio signals, control information and IR for remote control. The High

Performance Keypad has on-board 20 Watt per channel class D amplifiers to

provide a rich level of clean sound even in outdoor or large room applications.

It also contains a full set of features, including the ability to control all other

keypad volume controls in the house. Build a system that accommodates the

needs of any space by combining the lyriQ™ High Performance Keypad with

the lyriQ™ Standard Keypad (P/N AU7394-xx) in the same system. The

AU1000-xx is available in white (-WH), light almond (-LA), ivory (-IV), or black

(-BK).

2. Description

The front panel of the lyriQ™ High Performance Keypad, PN AU1000-xx (see

Figure 1), looks almost identical to the lyriQ™ Standard Keypad (AU7394-xx). It

also has push buttons for VOLUME UP/DOWN (with five associated green

Volume Bar Graph LEDs), SOURCE (with four green Source Selection LEDs)

and MUTE (with one red status LED). There is also an IR target window and tri-

colored status LED. The visual cue from the front panel that this is a High

Performance Volume Control are the parenthesis surrounding the music note in

the lower right hand corner.

NOTE: lyriQ™ Keypads are recommended for indoor use only.

On the rear of the lyriQ™ High Performance Keypad (see Figure 2) the Category

5 connection is an RJ45 jack (J1). The TB2 speaker output connections (left and

right, plus and minus) are spring loaded and designed to support up to 14 gauge

wire. The TB3 Line Out connections (plus and minus) are also spring loaded and

designed to support up to 14 gauge wire. This mono-summed output is designed

for powered sub-woofers and as such is filtered through an 80Hz low pass filter.

The other terminal block on the rear (TB1) is used for powering the keypad. Up to

14 gauge speaker wire may be used for this purpose, and this speaker wire (two

conductor or four conductor) is run from a power distribution module (P/N

AU1001) in the enclosure to the ketpad. We recommend 16/4 speaker wire,

since it is available paired with Category 5 from a variety of sources. Again, the

TB1 connections are spring loaded (plus and minus) with the two plus

connections on the red portion of TB1 and the two minus connections on the

black portion of TB1. For ease of installation, connect the red wire and white wire

to the red (plus) portion of TB1 and the black and green wire to the black (minus)

portion of TB1.

Figure 1

Figure 2

301 Fulling Mill Road, Suite G

Middletown, PA 17057

Phone (800) 321-2343 / Fax (717) 702-2546

www.onqlegrand.com

Page 2 of 9

INSTRUCTION/INSTALLATION SHEET

lyriQ™ High Performance Keypad

IS-0369 REV. E



3. Installation

Installation of the lyriQ™ High Performance Keypad is best accomplished at multiple times during new

construction, at “Rough-in” before the drywall is installed, and at “Trim-out” after the drywall is installed and

painted.

NOTE: Before connecting the keypads: Make sure that power supplies are not connected to the lyriQ™

Audio and Power Distribution Modules. For instructions on pre-wiring and installing other components of

the lyriQ™ Audio System, please see the Instruction Sheets included with those components.

NOTE: Always follow TIA-570-B wiring standards for installing and terminating Category 5 cable. Failure to

follow the correct wiring standard could result in damaged equipment and/or electrical interference issues.

NOTE: Maintain a minimum 12” separation between Category 5 cable and any 120VAC cabling.

A. “Rough-in” steps:

1) A single Category 5 cable and 16/4 speaker wire should be run from the enclosure location to a single

gang outlet box or mud ring at each Volume Control location.

B. “Trim-out” steps:

1) Connect the volume control by terminating the pre-wired Category 5 cable from the enclosure with an

RJ45 plug, following the T568A wiring standard and insert this plug into jack J1 (see Figure 2).

2) For the power connection (TB1) strip 3/8” of insulation from each of the four conductors and insert the

red and white wires into the red (plus) portion of TB1. Insert the stripped black and green wires into the

black (minus) portion of TB1 (see Figure 2).

NOTE: The two red connections are tied together, as are the two black connections. They are

provided in pairs to provide flexibility of wiring.

NOTE: Electricians may prefer to think of the black and red wires as plus and the green and white

wires as minus. That wiring will also work, as long as it is also followed at the other end of the cable

(at the Power Distribution Module in the enclosure).

3) Speaker/Line Out/Sub-Woofer connections (see Figure 2):

NOTE: Polarity and channels are clearly marked (L+, L-, R-, R+) for proper identification during

installation.

a) Use TB2 to connect one pair (only) of 8 ohm evōQ™ audio speakers to the volume control.

b) Use TB3 to connect your evōQ™ powered sub-woofer or an external amplifier to the volume control.

These connection terminals do not provide any amplification but the volume control on the keypad

controls the output level of this connection.

4) Connections in the enclosure (see Figure 3):

Produkt Specifikationer

Mærke:	On-Q
Kategori:	Hi-Fi system
Model:	lyriQ

Har du brug for hjælp?

Hvis du har brug for hjælp til On-Q lyriQ stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Hi-Fi system On-Q Manualer

On-Q lyriQ Manual

20 August 2024

Hi-Fi system Manualer

Nyeste Hi-Fi system Manualer

AMX Modula AVS-MD-3216-007 Manual

14 September 2025

Starkey Z Series IIC Manual

14 September 2025

Starkey VFusion Manual

14 September 2025

Starkey S Series ITE Manual

14 September 2025

Starkey Destiny 1600 BTE Manual

14 September 2025

Starkey X Series mini BTE Manual

14 September 2025

Starkey S series BTE Manual

14 September 2025

AMX Octaire AVS-OCT-6432-007 Manual

14 September 2025

Starkey S Series iQ BTE Manual

14 September 2025

Starkey ZON RIC Manual

14 September 2025