Onkyo SKF-101 Manual

Onkyo Højttaler SKF-101

Læs gratis den danske manual til Onkyo SKF-101 (2 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Onkyo SKF-101, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Thank you for your purchase of the Onkyo speaker system.
Please read this manual thoroughly before using it.
Following the instructions in this manual will enable you to
obtain optimum performance and listening enjoyment from
your new speaker system.
Please retain this manual for future reference.
Before using this unit
The speaker cabinet is made of wood and is therefore
sensitive to extreme temperatures and humidity. Avoid
placing the speaker systems in locations subjected to direct
sunlight, or in smokey or in humid places, such as near an
air conditioner, humidifier, bathroom, or kitchen. Doing so
may result in damage to the speaker.
Place the unit on a rigid, level surface. Placing it on a
slanted surface or weak base not only may cause the unit to
fall, but also results in decreased sound quality.
Be sure to turn off your amplifier before connecting the
speaker system. Connecting them with the amplifier's power
on may result in damage to the amplifier or the speaker
system.
Keep water or other liquids away from the unit. If water is
spilled into the unit, not only the unit but also the speakers
themselves may be damaged.
Name and function of each part
Connection
Turn the sound volume to the minimum and disconnect the
power cord to the amplifier before connecting the speaker
cables.
The nominal impedance of this speaker system is 6 . UseΩ
only amplifiers capable of handling this impedance.
Use the supplied speaker cables to connect between
speaker 's binding posts and the amplifier's speaker
terminals as illustrated below.
Connect the speaker cables securely to the terminals, with
the core wires twisted properly. In this case, make sure that
the core wires do not touch each other. Note that a short
circuit in core wires may result in damage to the amplifier.
✩ This speaker system uses banana-plug compatible binding
posts.
Connect the Right and Left speakers (as viewed from the
listening position) to the amplifier's corresponding Right
and Left speaker terminals.
Before turning on the amplifier's power switch:
Make sure that the positive (+) and negative (–) speaker
cables do not contact each other. Otherwise, a short-circuit
may occur, causing damage to the amplifier.
Be sure to connect the speaker cables with correct polarity
(connect the speaker's positive (+) and negative (–) binding
posts with the amplifier's corresponding speaker terminals).
Reversed polarity results in impaired bass-range
reproduction, causing mislocalization of the sound image.
Also, be sure to connect the Right and Left speakers with
the amplifier's corresponding speaker terminals.
Pull lightly on the speaker cables to ensure that they are
connected firmly.
R L
R L
Ordinary connection (single-wiring)
1. Loosen the LOW-FREQUENCY binding post screws, with the
jumper bars attached.
2. Insert the speaker wires to the connection holes. Fasten the
screws securely again.
* To use banana-plug speaker cables, insert the banana plug
into the center hole of each binding post.
Note:
Make sure that the HIGH-FREQUENCY jumper bars are not
loosened.
Bi-wiring connection (Remove the attached jumper bars.)
1. Using two sets of speaker cables, connect the HIGH FRE-
QUENCY and LOW-FREQUENCY binding posts
independently to your amplifier.
2. On the amplifier, connect the speaker cables to the speaker
output terminals paying close attention to maintain consistent
polarity (See below.).
Remove the
jumper bars.
Amplifier's speaker output
terminals
(Or AV amplifier's front
speaker output terminals)
Amplifier's speaker output terminals
(Or AV amplifier's front speaker output
terminals)
Cabinet
Grille
Grille plug holes
Woofer
Tweeter
Bass-reflex port
216 mm 285 mm
921 mm
LOW-FREQUENCY binding post
HIGH-FREQUENCY binding post
SKF-101
SPEAKER SYSTEM
Instruction Manual

Produkt Specifikationer

Mærke: Onkyo
Kategori: Højttaler
Model: SKF-101

Har du brug for hjælp?

Hvis du har brug for hjælp til Onkyo SKF-101 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Højttaler Onkyo Manualer

Onkyo

Onkyo D-407M Manual

15 September 2024
Onkyo

Onkyo SKS-3600 Manual

5 August 2024
Onkyo

Onkyo Smart Speaker G3 VC-GX30 Manual

29 Juli 2024
Onkyo

Onkyo D-105F Manual

28 Juli 2024
Onkyo

Onkyo SBX-300 Manual

27 Juli 2024
Onkyo

Onkyo D-407C Manual

25 Juli 2024
Onkyo

Onkyo SKF-L500 Manual

25 Juli 2024
Onkyo

Onkyo SKH-410 Manual

24 Juli 2024
Onkyo

Onkyo SKS-L500 Manual

24 Juli 2024
Onkyo

Onkyo SKS-HT978 Manual

23 Juli 2024

Højttaler Manualer

Nyeste Højttaler Manualer

DS18

DS18 PRO-SDF6R Manual

4 November 2025
DS18

DS18 35D200NO-4 Manual

4 November 2025
DS18

DS18 6PRO600SE-8 Manual

4 November 2025
Lenco

Lenco BTC-020 Manual

4 November 2025
W-KING

W-KING T9-2 Manual

4 November 2025
Orava

Orava Capella-1B Manual

4 November 2025
Victrola

Victrola Willow VRS-2800 Manual

3 November 2025
Hama

Hama Bomb 3.0 00188234 Manual

3 November 2025
Hama

Hama Mate Pro MK II 00188231 Manual

3 November 2025
Alpine

Alpine QLP952SLR-2 Manual

3 November 2025