Onkyo SKS-4600 Manual

Onkyo Højttaler SKS-4600

Læs gratis den danske manual til Onkyo SKS-4600 (4 sider) i kategorien Højttaler. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Onkyo SKS-4600, eller vil du spørge andre brugere om produktet?

Side 1/4
En
Thank you for your purchase of the Onkyo speaker
system.
Please read this manual thoroughly before using it.
Following the instructions in this manual will enable
you to obtain optimum performance and listening
enjoyment from your new speaker system.
Please retain this manual for future reference.
SKF-4600
SKS-4600
Speaker System
Instruction Manual
Before using this unit
The speaker cabinet is made of wood and is therefore
sensitive to extreme temperatures and humidity.
Avoid placing the speaker systems in locations
subjected to direct sunlight, or in smoky or in humid
places, such as near an air conditioner, humidifier,
bathroom, or kitchen. Doing so may result in damage
to the speaker.
Place the unit on a rigid, level surface. Placing it on a
slanted surface or weak base not only may cause the
unit to fall, but also results in decreased sound
quality.
Be sure to turn off your amplifier before connecting
the speaker system. Connecting them with the
amplifier's power on may result in damage to the
amplifier or the speaker system.
Keep water or other liquids away from the unit. If
water is spilled into the unit, not only the unit but also
the speakers themselves may be damaged.
Precaution on use
This speaker system can handle the specified input
power when it is used for ordinary music
reproduction. If the following abnormal signals are fed
to the speaker, however, an overcurrent may flow in
the internal circuits, causing burning or breakage of
the wires even if the input power is below the
specified rating.
1. Noise produced when FM station is not tuned in
2. Sound produced when fast-forwarding cassette
tape deck
3. High-frequency sound generated by an oscillator,
an electronic musical instruments, etc.
4. Oscillating amplifier signals
5. Special test signals produced by audio checking
CD, etc.
6. Sound produced when connecting or
disconnecting audio connection cables (Always
turn off the amplifier’s power before connecting or
disconnecting cables.)
7. Howling when a microphone is used
Do not place magnetic objects such as screwdrivers
and iron parts near the tweeter since they use
speakers with strong magnets. Otherwise, the
objects may be attracted, causing injury or damaging
the diaphragm.
En-2
Model name
SKF-4600
Front speaker system 2×
SKS-4600
Center speaker system SKC-4600 × 1
Surround speaker system SKM-4600 × 2
Connection
Turn the sound volume to the minimum and disconnect the
power cord from the amplifier before connecting the
speaker cables.
The nominal impedance of this speaker system is 6 . Use
only amplifiers capable of handling this impedance.
Use the supplied speaker cables to connect between
speakers input terminals and the amplifiers speaker
terminals as illustrated below.
Connect the speaker cables securely to the terminals, with
the core wires twisted properly. In this case, make sure that
the core wires do not touch each other. Note that a short
circuit in core wires may result in damage to the amplifier.
Connecting to AV amplifier
SKF-4600
SKC-4600 / SKM-4600
Before turning on the amplifier’s power switch:
Make sure that the positive (+) and negative (-) speaker
cables do not contact each other. Otherwise, a short-circuit
may occur, causing damage to the amplifier.
Be sure to connect the speaker cables with correct polarity
(connect the speaker’s positive (+) and negative (-) binding
posts with the amplifiers corresponding speaker
terminals). Reversed polarity results in impaired bass-
range reproduction, causing mislocalization of the sound
image. Also, be sure to connect the Right and Left
speakers with the amplifiers corresponding speaker
terminals.
Pull lightly on the speaker cables to ensure that they are
connected firmly.
L
27122965
REMOTE
CON TROL
CAUT ION: SP EAKER IMPEDANCE
6 OHMS MIN . /SPEAKER
ANT ENNA
FM
75
AM
COAXIALOPTI CAL
12
IN IN IN IN FRONT SURR CENTER
SUB
WOOFER
VID EO 2 VIDEO 1
OUT
DIG ITAL INP UT
DVD
MONIT OR
OUT
DVD
TAP ECD
SUBWOOFER
PRE OUT
L
R
R
VID EO 3
VID EO 2VID EO 3 VID EO 1
VID EO
OPTI CAL
ININ IN I N
DIG IT AL
OUT PUT
IN
IN PUT 1IN PUT 2 OUTPUT
COMPONENT VID EO
P
R
P
B
Y
OUT
OUT
DIG IT AL
INPUT
L
R
S VID EO
FRONT
SPEAKERS
SURROUND
SPEAKERS
CENT ER
SPEAKER
R
L
R
L
A B
SURROUND BACK
SPEAKER
R
L
AC OUT LET S
SWITCHED
TOTAL 100W MAX.
AC 230-240
V
50
Hz
SURROUND BACK
SPEAKER
++
+
++
FRONT
SPEAKERS
SURROUND
SPEAKERS
CENTER
SPEAKER
R
L
R
L
A B
R
L
SKF-4600
Front right
speaker
SKC-4600
Center speaker
SKM-4600
Surround right
speaker
SKF-4600
Front left
speaker
SKM-4600
Surround left speaker
Red
Green
Blue
Gray
AV Amplifier
White
1. Strip the insulation of speaker cables,
and twist the core wires tightly.
2. While pressing the lever, insert the wire
into the hole, and then release the lever.
3. Make sure that the terminals are gripping
the core wires, not the insulation.
15 mm
1. Strip the
insulation of
speaker
cables, and
twist the core
wires tightly.
2. Loosen the
terminal screw, and
insert the wire into
the hole (until the
core wires are
inserted fully).
3. Fasten the
terminal
screw.


Produkt Specifikationer

Mærke: Onkyo
Kategori: Højttaler
Model: SKS-4600

Har du brug for hjælp?

Hvis du har brug for hjælp til Onkyo SKS-4600 stil et spørgsmål nedenfor, og andre brugere vil svare dig