Oricom HP200 Manual

Oricom Ikke kategoriseret HP200

Læs gratis den danske manual til Oricom HP200 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 3.9 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Oricom HP200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

HP200

Corded Hotel Phone with

Speakerphone

Keep this user guide for future reference

Installation

Connection

1. Connect one end of the curly cord to the handset,

and the other end to the socket marked

HANDSET on the left-hand side of the base.

2. Connect the telephone line cord to the LINE IN

socket on the telephone, and to a telephone

network wall socket.

3. Lift the handset and listen for the dial tone. Your

telephone is now operational.

4. Ensure the correct Recall time has been set for

your system PBX or phone network

For Desk Use

Fit the desk support onto the base of the phone.

Location of controls

Redial

321

ABC DEF

GHI

MNO

PQRS

T UV

WXYZ

Messages

SpeakerMute

Recall

Volume

Concierge Wake Up Cal l Air por t Taxi Emergency

Reception Out side Li ne Room S ervice Restauran t HouseKeeping

JKL

Store

Progr am/Store 100 300 600

Progr amer

2 1

Wall mounting your phone:

For wall mounting installation, do not insert the desk

support on the base.

1. Revolve the handset catch 180° to the wall

mounting position using a small coin.

2. Connect the telephone line cord to the LINE IN

socket on the telephone, and to a telephone wall

socket.

3. Run the telephone cable inside the groove and

ensure it is tight.

4. Drill two holes vertically, one above the other,

83mm apart, and leave the screws protruding

from the wall by 5mm.

5. Align the base’s keyhole slots with the screws and

slide the phone downward to secure it.

6. Lift the handset. Listen for the dial tone to ensure

the telephone is working.

1. Program/Store switch

2. Programmer switch

3. Hook switch

4. Handset holder

5. Speaker

6. Keypad

7. Handset cord jack

8. Handset volume control button

9. Message Waiting and Visual

Ringer indicator

10. Telephone line jack

11. Recall time 100/300/600

switch

12. Message Waiting switch

13. Line 1/2 switch

14. Store button

15. Data port

16. One touch memories

17. Ringer volume Hi/Lo switch

18. Redial button

19. Recall button

20. Speaker volume control

21. Speaker button with LED

22. Mute button

23. Messages button

Making a call

1. Lift the handset or press button the LED Speaker

lights, then dial tone will be heard.

2. Dial the required telephone number The number

will be dialed.

3. On completion of the call, hang up the handset or

press the Speaker button again.

Answering a incoming call

1. When an incoming call is received, the phone will

ring,

2. Pick up the handset or press the Speaker button

to answer the call.

3. On completing the call, hang up the handset or

press the Speaker button again.

Redial

1. Lift the handset or press Speaker button.

2. Press Redial to dial the last number dialled.

Volume control

The handset earpiece volume may be increased or

decreased during a call. Press the Volume button to

increase or decrease the volume.

To adjust the speaker volume (hands free dialling/group

listening) use the / buttons for a comfortable

levels.

Recall (Australia ONLY)

You can use the Recall button on your telephone when

using your network operator’s services such as call

waiting etc. A subscription may apply for these services,

contact your network operator for more information. If

this is not working correctly check the country option of

the phone menu and select Australia or New Zealand

option. For Australia it should be set to 100ms and for

New Zealand is 600ms.

Mute button

The handset and speaker volume can be muted during

a call by pressing button. Release the MUTE MUTE

button to reactivate the microphone.

Ringer volume control

The ringer volume can be adjusted using the Ring

Volume switch located on the right-hand side of the

telephone

Memory

This telephone has 10 One-Touch memories.

Storing One-Touch Memories

1. Ensure the Program/Store switch is set to Store.

2. Lift the handset or press Speaker button, dial

tone will be heard (ignore any tone). Press Store

button.

3. Enter the telephone number to be stored (up to 32

digits). Press Store.

4. Select a memory position by pressing the

corresponding memory button.

y p p

press Redial.

If you need to change a number, store the new number

in the same location as the old one.

Dialling using One-Touch Memories

1. Lift the handset or press Speaker button, dial

tone will be heard.

2. Press the required One-Touch memory button.

Messages button

You can also store a telephone number into this button

like the one touch memory buttons:

1. Ensure the Program/Store switch is set to Store.

2. Pick up the handset or press the Speaker button,

the dial tone will be heard. (ignore the dial tone)

press Store button.

3. Enter the telephone number to be stored (up to 32

digits). Press Store.

4. Press the Messages button, now number have

been stored.

5. Replace the handset.

Dial the pre-programmed number

1. Lift the handset. You will hear the dial tone.

2. Press the MESSAGES button. A pre programmed

number will be dialed automatically.

Line Switch

There is a line switch on the top of the unit allows you

select the desired telephone line 1 or line 2 depends on

your selection.

You may configure the phone using the switch located

under the inlay on the base of the phone marked 1 2, so

that the telephone (1) and the outer port (2) are

connected in parallel.

Connection of additional

equipment

Additional equipment such as modems can be

connected to this telephone via the DATA PORT socket

on the right side of the base. Two methods of operation

can be selected by using the switch located

on the top of the base (Please refer to "Location of

controls" point 12):

1. Allows for single line parallel operation. For example,

a computer modem can be operated through the

telephone but only one device can be operated at a

time, either the modem or the telephone.

2. Allows for two line operation where a computer

modem can be connected via the telephone and both

devices can be used at the same time. The network

wall socket must have two lines connected.

Hearing aid compatible

This telephone is hearing aid compatible. Select the T

mode on your hearing aid to enable this feature.

Produkt Specifikationer

Mærke:	Oricom
Kategori:	Ikke kategoriseret
Model:	HP200

Har du brug for hjælp?

Hvis du har brug for hjælp til Oricom HP200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Oricom Manualer

26 August 2025

20 August 2025

11 Februar 2025

10 Februar 2025

Oricom Rock Light Manual

10 December 2024

Oricom Eclipse OBHSSOO Manual

19 August 2024

18 August 2024

16 August 2024

14 August 2024

13 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Cougar GR 650 Manual

27 August 2025

Paragon PSG-161-SEG-PL-NP Manual

27 August 2025

Full Boar FBAHR-032 Manual

27 August 2025

Juice Goose RP100-15A Manual

27 August 2025

Maxview Roam 5G COMBO60 Manual

27 August 2025

Asus ZenWiFi BD4 Outdoor Manual

27 August 2025

ENTES FG-4 Manual

27 August 2025

YSI MultiLab IDS Manual

27 August 2025

True TH-23G~FGD01 Manual

27 August 2025

Dualit Architect 16018 Manual

27 August 2025