OSD Audio IWS-88 Manual

OSD Audio Subwoofer IWS-88

Læs gratis den danske manual til OSD Audio IWS-88 (2 sider) i kategorien Subwoofer. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6 anmeldelser. Har du et spørgsmål om OSD Audio IWS-88, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

18AWG minimum - for distances up to ………………………. . 10 ft

16AWG - from ……………………………………………. 10 to 50 ft

14AWG - from …………………………………………… 50 to 100ft

- Where is the best place to install the speakers

- Where do the speakers sound the best

- When placing the speakers in the wall, try to locate them so that the

sound is projected towards the general listening area.

- If you intend to paint the grilles, try to do so before installation.

Quick installation guide

- Pencil

- Drill

- Tape Measure

- Wire cutter

- Philips-head screwdriver

- Sandpaper

Tools needed for installation

STEP 1

Trace along the inclusive template. Cut along the traced line using a

drywall saw or rotary drill. A simple, inexpensive drywall saw (about

$10 at your local hardware store) is the best choice for beginners.

Caution: This is the most important part of the entire installation.

If you are not certain whether any obstructions exist behind the

desired mounting area, you should start by cutting a small hole in

the center of your penciled mounting hole with a drywall saw. Use a

piece of sandpaper to sand down the cut out edge for a smoother

contour. (See Diagram 1 and Diagram 2)

Run the cable into the cut out location while leaving an extra two

feet to make the connection to the speaker easier. St

STEP 2

rip back

approximately ½” of the speaker cable insulation and twist

the copper wires tightly for easy insertion.

On the back of the speaker, press down on the gold-plated

compression terminal to reveal the "eye" and insert the speaker

cable through the eye for secure connection. Release the compres-

sion terminal to lock each cable securely.

Diagram 1:

Cutout tracing

Diagram 2:

Cut Out

To determine the length and the gauge of speaker wire, you will need to

measure the distance between your receiver/amplifier and the speakers.

- Always buy more than you think you would need.

- Equal wire lengths should always be used to maintain an equal

balance in sound volume.

- Sound quality is lost when using thin wire gauge over a long

distance.

- Utility knife

- Safety eyewear

- Gloves

Speaker wire

- -

- Measure the distance from the receiver/amplifier to the speakers.

-----------------

----------------

-----------------

----------------

-----------------

STEP 3

Tighten the dog-ear brackets by simply turning the screws on the

slowly clockwise. The quick-turn mounting system and frame will

"sandwich" or clamp around the wall to hold the speaker securely in

place. (See Diagram 3)

Diagram 3:

Mounting Dog Ear

Closed

Loose

Closed

Loose

..... ......

......

dog ear

STEP 4

Screw Screw

Tighten the four mounting screws with the same amount of force until

the speaker is aligned and held securely to the wall surface. Caution:

do not over tighten! (See Diagram 4)

Diagram 4:

MANUAL

DUAL 8" IN-WALL

S U B W O O F E R

IWS88

Produkt Specifikationer

Mærke:	OSD Audio
Kategori:	Subwoofer
Model:	IWS-88
Bredde:	290.5 mm
Dybde:	101.6 mm
Højde:	479.4 mm
Vægt:	- g
Brugervejledning:	Ja
Produktfarve:	Black, White
Udgangseffekt (RMS):	240 W
Hurtig start guide:	Ja
Anbefalet brug:	Universel
Frekvensområde:	45 - 500 Hz
Impedens:	8 ohm (Ω)
Forbindelsesteknologi:	Ledningsført
Lyd-output kanaler:	2.0 kanaler
Højttaler, placering:	Ceiling-mountable, In-wall/in-ceiling
Diskanthøjttaler:	Ingen
Antal drivere til diskant:	1
Sensitivitet:	90 dB
Multi-rum streaming support (MRS):	Ingen
Bashøjttaler:	Ja
Antal bashøjttalerdrev:	1
Woofer diameter:	203.2 mm
Forstærker:	Ingen
AirPlay:	Ingen
Woofer diameter (britisk mål):	8 "
Egnet til udendørs brug:	Ja