Ozito PXCG-060 Manual

Ozito Batterioplader PXCG-060

Læs gratis den danske manual til Ozito PXCG-060 (2 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 41 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 21 anmeldelser. Har du et spørgsmål om Ozito PXCG-060, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

THIS MANUAL CONTAINS IMPORTANT SAFETY AND OPERATING INSTRUCTIONS FOR

YOUR CHARGER.

1. Before using the charger read all instructions and cautionary markings on the charger, battery

pack and the product using the battery pack.

2. This charger is not intended for any uses other than charging Ozito Power X Change rechargeable

batteries. Any other use may result in risk of re, electric shock or electrocution.

3. Do not place any object on top of the charger or place the charger on a soft surface that may

result in excessive internal heat. Place the charger in a position away from any heat source.

4. To reduce risk of damage to the electric plug and cord, pull by the plug rather than the cord when

disconnecting the charger.

5. Make sure the cord is located so that it will not be stepped on, tripped over, or otherwise

subjected to damage or stress.

6. An extension cord should not be used unless absolutely necessary. Use of an improper extension cord

could result in the risk of re, electric shock or electrocution.

7. Do not operate the charger if it has received a sharp blow, been dropped or otherwise damaged in

any way. Have it checked by an electrician or power tool repairer.

8. Do not disassemble charger. Take it to an electrician or power tool repairer when service or repair

is required. Incorrect reassembly may result in a risk of electric shock, electrocution or re.

9. To reduce risk of electric shock, unplug the charger from the outlet before attempting any

cleaning. Removing the battery pack will not reduce this risk.

10. Never attempt to connect 2 chargers together.

11. The charger is designed to operate on standard household electrical power (240 volts). Do not

attempt to use it on any other voltage!

12. DO NOT USE the charger where the temperature may reach below 0° or exceed 40°C. If the

battery pack is too hot or too cold charging will cease and begin automatically only when battery

reaches correct charging temperature.

13. Do not incinerate the battery pack even if it is seriously damaged or is completely worn out. The

battery can explode in a re.

14. Never attempt to open the battery pack for any reason. If the plastic housing of the battery pack breaks

or cracks, immediately discontinue use and do not recharge.

15. During charging, the battery must be placed in a well ventilated area.

CHARGER SAFETY WARNINGS

ELECTRICAL SAFETY

WARNING! When using mains-powered tools, basic safety

precautions, including the following, should always be followed to

reduce risk of ﬁre, electric shock, personal injury and material damage.

Read the whole manual carefully and make sure you know how to switch the tool off in an emergency,

before operating the tool.

Save these instructions and other documents supplied with this tool for future reference.

Note: The supply of 230V and 240V on Ozito tools are interchangeable for Australia and New Zealand.

This charger is double insulated therefore no earth wire is required.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly

qualied persons in order to avoid hazard.

Note: Double insulation does not take the place of normal safety precautions when operating this tool.

The insulation system is for added protection against injury resulting from a possible electrical insulation

failure within the tool.

Using an Extension Lead

Always use an approved extension lead suitable for the power input of this tool. Before use, inspect

the extension lead for signs of damage, wear and ageing. Replace the extension lead if damaged or

defective.

When using an extension lead on a reel, always unwind the lead completely. Use of an extension lead

not suitable for the power input of the tool or which is damaged or defective may result in a risk of re

and electric shock.

To reduce the risk of electric shock, we recommend the use of a residual current device (rated 30mA or

less).

This appliance is not intended for use by persons (including children) with reduced physical, sensory or

mental capabilities, or lack of experience and knowledge, unless they have been given supervision or

instruction concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the appliance.

CARING FOR THE ENVIRONMENT

Power tools that are no longer usable should not be disposed of with household

waste but in an environmentally friendly way. Please recycle where facilities exist.

Check with your local council authority for recycling advice.

Recycling packaging reduces the need for landll and raw materials. Reuse of

recycled material decreases pollution in the environment. Please recycle packaging

where facilities exist. Check with your local council authority for recycling advice.

DESCRIPTION OF SYMBOLS

SPECIFICATIONS

Input: 220-240V ~AC 50-60Hz

Output: 18V DC, 1.5A

Battery Charge Time: 60Min - PXBP-150 (18V 1.5Ah)

80Min - PXBP-200 (18V 2.0Ah)

120Min - PXBP-300 (18V 3.0Ah)

160Min - PXBP-400 (18V 4.0Ah)

215Min - PXBP-520 (18V 5.2Ah)

215Min - PXUBP-520 (18V 5.2Ah Ultra)

1. Charging Unit LEDs

2. Charging Unit

ozito.com.au

STANDARD CHARGER

INSTRUCTION MANUAL

PXCG-060

ONLINE MANUAL

Scan this QR Code with your

mobile device to take you to the

online manual.

Double Insulated

Volts Hertz

Amperes Amp Hour

Read Instruction Manual

Indoor Use Only Do not dispose of in rubbish

Regulatory Compliance

Mark (RCM)

Do not charge battery in

temperatures exceeding 40 C°

2.0A Slow Blow Fuse Warning

>40°C

V Hz

A Ah

T2A

1. CHARGING A BATTERY

Charger LED Indicator Lights

LED Indicator Situation

GREEN (Flashing) Stand By (no battery pack is inserted)

RED (Flashing) Battery is charging (low charge)

RED (Illuminated) Battery is fast charging (mid charge)

GREEN (Illuminated) Battery is fully charged and is ready for use. Refer to

charging times to ensure the battery is fully charged.

BOTH(Illuminated) Battery pack is too hot or too cold (charging will begin

automatically when battery reaches correct charging

temperature).

BOTH (Flashing) The battery is deffective, charging is no longer

possible. Do not charge. Contact Ozito Customer

Service.

CAUTION: THE CHARGER SHOULD BE PROTECTED BY

A RESIDUAL CURRENT DEVICE (RATED AT 30MA OR

LESS).

1. Place the charger on a at

surface then connect the charger

into a mains power outlet.

3. Align and then slide the ribs on

the battery into the recess in the

charger.

2. The charger LED will ash green

showing power is being supplied

to the charger.

4. The red LED will illuminate while

the battery charges.

5. The green LED will illuminate

once the battery is fully charged.

2. MAINTENANCE

• Disconnect the charger from power source before cleaning.

• Keep the charger in a dry place out of reach of children.

• If the enclosure of the charger requires cleaning, do not use solvents. Use a dry, soft

cloth only to wipe down the surface. Never let any liquid get inside the charger; never

immerse any part of the charger.

• There are no other parts inside the charger which require maintenance. Do not

take the charger apart. If the charger is damaged, contact your supplier or the

manufacturer.

Mounting The Charging Unit On A Wall

The charging unit can be mounted to a wall or workbench.

The correct dimensions for drill holes can be found on the back of the charging unit; a

template for the mounting hole locations can also be found on the Ozito website.

Note: When mounting on a wall you must use suitable screws, e.g.M3 pan-head

screws, in order to prevent damage to the housing and risk of falling. OZITO Australia/New Zealand (Head Ofce)

1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.

0219

WARRANTY

IN ORDER TO MAKE A CLAIM UNDER THIS WARRANTY YOU

MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS

WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO

RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE

OUR CUSTOMER SERVICE HELPLINE:

Australia 1800 069 486

New Zealand 0508 069 486

TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL

NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER

SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND

ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE

WARRANTY POLICY OR PROCEDURE.

The benets provided under this warranty are in addition to other rights and

remedies which are available to you at law.

Our goods come with guarantees that cannot be excluded at law. You are

entitled to a replacement or refund for a major failure and for compensation

for any other reasonably foreseeable loss or damage. You are also entitled to

have the goods repaired or replaced if the goods fail to be of acceptable

quality and the failure does not amount to a major failure.

Generally you will be responsible for all costs associated with a claim under

this warranty, however, where you have suffered any additional direct loss as

a result of a defective product you may be able to claim such expenses by

contacting our customer service helpline above.

36 MONTH REPLACEMENT WARRANTY

Your product is guaranteed for a period of 36 months from the original date

of purchase and is intended for DIY (Do It Yourself) use only. If a product is

defective it will be replaced in accordance with the terms of this warranty.

Warranty excludes consumable parts.

WARNING

The following actions will result in the warranty being void.

• If the tool has been operated on a supply voltage other than that specied

on the tool.

• If the tool shows signs of damage or defects caused by or resulting from

abuse, accidents or alterations.

• Failure to perform maintenance as set out within the instruction manual.

• If the tool is disassembled or tampered with in any way.

PXCG-060

Produkt Specifikationer

Mærke:	Ozito
Kategori:	Batterioplader
Model:	PXCG-060

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito PXCG-060 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Ozito Manualer

Ozito PXBP-400U Manual

2 September 2024

Ozito PXCG-030U Manual

9 August 2024

Ozito OJL-325 Manual

22 Juli 2024

Ozito PXMBC-002 Manual

23 Januar 2024

Ozito OCBC-1000 Manual

22 November 2023

Ozito PXCG-120U Manual

26 August 2023

Ozito OCBC-400 Manual

3 Juli 2023

Ozito OCBC-200 Manual

17 November 2022

Ozito OCBC-600 Manual

13 November 2022

Ozito PXCG-060 Manual

25 Oktober 2022

Batterioplader Manualer

Nyeste Batterioplader Manualer

Tripp Lite PR3/UL Manual

31 Juli 2025

RYOBI RC43P Manual

31 Juli 2025

Tripp Lite U280-Q01FL-BK-2 Manual

31 Juli 2025

Tripp Lite HCINT150SL Manual

30 Juli 2025

ISDT Limeta MC234AC Manual

29 Juli 2025

Ikea STENKOL 605.247.41 Manual

29 Juli 2025

ISDT Limeta NeoGo Manual

29 Juli 2025

Hamilton Buhl LTT10 Manual

29 Juli 2025

Satechi Qi2 Trio Wireless Charging Pad Manual

29 Juli 2025

Panasonic BQ-CC65 Manual

25 Juli 2025