Ozito SCMS-1621 Manual

Ozito savemaskine SCMS-1621

Læs nedenfor 📖 manual på dansk for Ozito SCMS-1621 (8 sider) i kategorien savemaskine. Denne guide var nyttig for 24 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/8
ozito.com.au
DOUBLE BEVEL
SLIDE COMPOUND
MITRE SAW
210mm (8¼”)
INSTRUCTION MANUAL
SPECIFICATIONS
Motor: 1800W (S2 5min),
1500W (S1)
No Load Speed: 5,000/min
Blade: Ø210mm x Ø16 x 48T
Mitre Angle: 0-45 left & right°
Bevel Angle: 0-45 left & right°
Max. Cutting Capacity:
Mitre 0 x Bevel 90 : 62 x 310mm° °
Mitre 45 x Bevel 90 : 62 x 210mm° °
Mitre 0°x Bevel 45°: 36 x 310mm
Mitre 45°x Bevel 45°: Left 36 x 210mm
Right 20 x 210mm
SCMS-1621
WHAT’S IN THE BOX
Material Clamp
Compound Mitre Saw
Material Support Bar x 2
Hex Key, 5 & 6mm
Dust Bag
WARRANTY
0616
IN ORDER TO MAKE A CLAIM UNDER THIS
WARRANTY YOU MUST RETURN THE PRODUCT
TO YOUR NEAREST BUNNINGS WAREHOUSE WITH
YOUR BUNNINGS REGISTER RECEIPT. PRIOR TO
RETURNING YOUR PRODUCT FOR WARRANTY
PLEASE TELEPHONE OUR CUSTOMER SERVICE
HELPLINE:
Australia 1800 069 486
New Zealand 0508 069 486
3 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 36 months from the
original date of purchase and is intended for DIY (Do It Yourself) use
only. If a product is defective it will be replaced in accordance with
the terms of this warranty. Warranty excludes consumable parts, for
example: blade, carbon brushes and dust bag.
WARNING
The following actions will result in the warranty being void.
• If the tool has been operated on a supply voltage other
than that specified on the tool.
• If the tool shows signs of damage or defects caused
by or resulting from abuse, accidents or alterations.
• Failure to perform maintenance as set out within the instruction
manual.
• If the tool is disassembled or tampered with in any way.
• Professional, industrial or high frequency use.
TO ENSURE A SPEEDY RESPONSE PLEASE
HAVE THE MODEL NUMBER AND DATE OF
PURCHASE AVAILABLE. A CUSTOMER SERVICE
REPRESENTATIVE WILL TAKE YOUR CALL
AND ANSWER ANY QUESTIONS YOU MAY
HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
OZITO Australia/New Zealand (Head Office) 1-23 Letcon Drive, Bangholme, Victoria, Australia 3175.
The benefits provided under this warranty are in addition
to other rights and remedies which are available to you at law.
Our goods come with guarantees that cannot be excluded
at law. You are entitled to a replacement or refund for a major
failure and for compensation for any other reasonably foreseeable
loss or damage. You are also entitled to have the goods repaired
or replaced if the goods fail to be of acceptable quality and the
failure does not amount to a major failure.
Generally you will be responsible for all costs associated with
a claim under this warranty, however, where you have suffered
any additional direct loss as a result of a defective product you
may be able to claim such expenses by contacting our customer
service helpline above.
ONLINE MANUAL
Scan this QR Code with your
mobile device to take you to
the online manual.
1. Retractable Safety Guard
2. Material Support Bar
3. Material Clamp
4. Fence
5. Mitre Table
6. Mitre Table Lock
7. Bevel Angle Pointer
8. Lock Down Pin
9. Spindle Lock Button
10. Trigger
MITRE SAW
KNOW YOUR PRODUCT
1. ASSEMBLY
1. Remove foam packaging materials and using the carry handle,
carefully lift the mitre saw from its box and place it on a level
work surface.
1. Squeeze the clamp at the
end of the dust bag, place
over the dust extraction
port.
1. Insert each bar into the
two holes located on
both sides of the base.
2. Release cutting head from its transport position. While holding
the head of the saw down release the lock down pin.
11. Carry Handle
12. Slide Lock
13. Stabilising Bar
14. Bevel Lock
15. Bevel Release
16. Laser Guide
17. Additional Support Feet
18. Table Insert
19. Release Lever
SETUP & PREPARATION
Unpacking
Material Support Bars
Dust Bag
WARNING!: ENSURE THE TOOL IS SWITCHED
OFF AND DISCONNECTED FROM THE POWER
SUPPLY BEFORE PERFORMING ANY OF THE
FOLLOWING PROCEDURES.
HOLD
DOWN
TIGHTEN
2. Tighten screw when in
place.
Material clamp will assist
securing timber when making
cuts.
Note: The clamp can be
mounted on either the left or
right.
Material Clamp
2. SET-UP AND ADJUSTMENTS
1. Loosen mitre
table lock
2. Rotate the mitre table to the
desired mitre angle (left or
right) as shown by the mitre
angle pointer
Mitre Angle Adjustment
MITRE ANGLE
POINTER
3. Tighten mitre table lock at selected angle
Bevel Angle Adjustment
3. Tighten bevel lock at selected angle
Note: The mitre table features positive click stops at 0°, 15°, 22.5°,
31.6° and 45° for quick setting of common mitre angles.
Bench Mounting
The base of the saw has four
bench mounting holes (1 each
corner) that can be used to
mount it to a workbench or
mitre saw stand. Use four
screws or bolts (not included)
to secure.
WARNING!: ENSURE THE MITRE TABLE LOCK
IS TIGHT BEFORE MAKING A CUT. FAILURE
TO DO SO MAY RESULT IN THE MITRE TABLE
MOVING DURING OPERATION AND CAUSE
SERIOUS PERSONAL INJURY.
WARNING!: ENSURE THE BEVEL LOCK IS
TIGHT BEFORE MAKING A CUT. FAILURE TO
DO SO MAY RESULT IN THE CUTTING HEAD
MOVING DURING OPERATION AND CAUSE
SERIOUS PERSONAL INJURY.
Trenching refers to restricting the depth of cut and permits a “trench”
to be cut in the workpiece.
Bevel Angle Adjustment
Trenching
1. Ensure the cutting head is
raised, move the trenching
stop to the right as far as it
will go.
2. To adjust the trenching
depth rotate the trenching
depth adjustment screw.
3. To check that the blade
stops at the desired position,
lower the cutting head
until the trenching stop
adjustment screw touches
the trenching stop.
4. When the correct depth is
set. Lock it in position using
the trenching depth lock nut.
Slide Lock
When cutting a narrow piece of
wood it is not necessary to use
the slide mechanism. In these
circumstances, push back the
cutting head and ensure the slide
locking knob is tight to prevent the
cutting head from sliding.
To ensure the saw is standing securely when not mounting to a
workbench or mitre saw stand. Screw the Additional Support Feet to
the feet of the mitre saw with the fasterners provided. Then swing
out the Stabilising Bar to the rear until it engages.
18mm
18mm
30mm
1. Loosen bevel
lock.
2. BEVEL LEFT - Tilt the cutting head
to the desired
bevel angle
left as shown
by the bevel
angle pointer.
2a. BEVEL RIGHT - Tilt
the cutting head slighty
LEFT then pull the
bevel release.
BEVEL ANGLE
POINTER
2b. Tilt the cutting head to the desired
bevel angle right as shown by the
bevel angle
pointer.
BEVEL ANGLE
POINTER
CAUTION!: FOR ALL TYPES OF CUTS ENSURE
THE SAW IS LOCKED INTO POSITION.
Depending on the cut, the
material clamp will need
to be mounted on the
appropriate side. When
performing bevel cuts,
the work clamp must be
on the opposite side of
the bevel (otherwise it will
interfere with the cutting
action).
The lower guard provides protection to your hands and limbs when
the mitre saw head is in the up position. During the operation of
the saw, when the saw is turned on and you are making a cut, the
lower guard retracts over the upper guard as the saw is lowered
into the work piece.
A compound mitre cut involves
using a mitre angle and a bevel
angle at the same time.
1.
2.
OPERATION
The tool is recommended for use with a residual current device
with a rated residual current of 30mA or less.
Retractable Safety Guard
CAUTION!: DO NOT USE THE MITRE SAW TO CUT
METAL OR MASONRY.
A straight cut is made by cutting
the grain of the workpiece. A
90 straight cut is made with the °
mitre scale set in the 0 .°
Mitre
45º< >45º
Mitre cuts are made with the
mitre scale set at an angle other
than 0°
Mitre
45º< >45º
A bevel cut is made by cutting
across the grain of the workpiece
with the blade angled to the
mitre table.
3. TYPES OF CUTS
Spindle Lock
The spindle lock prevents the
blade in the saw from rotating.
Depress and hold the spindle
lock while installing, changing,
or removing the blade. Never
press when blade is rotating.
Straight Cutting
When cutting a narrow piece of wood, it is not necessary to use the
slide mechanism.
Bevel Cutting
Fence
Make sure that no part
of the tool contacts the
upper fence when bevel
or compound mitre
cutting. Always make
a dry run with the saw
turned off and check
clearance. Tighten
securely before making
a cut.
Mitre Cuts
Note: For Bevel Cuts ensure the rear fence is adjusted for
blade clearance.
Compound Mitre CutsMaterial Clamp
1. To retract the lower guard,
slide the release lever right
with your thumb and press
handle down.
Max. cutting
capacity wood:
62 x 310mm
Max. cutting
capacity wood:
62 x 210mm
Max. cutting
capacity wood:
36 x 310mm
Max. cutting
capacity wood:
left 36 x 210mm
right 20 x 210mm

Produkt Specifikationer

Mærke: Ozito
Kategori: savemaskine
Model: SCMS-1621

Har du brug for hjælp?

Hvis du har brug for hjælp til Ozito SCMS-1621 stil et spørgsmål nedenfor, og andre brugere vil svare dig


savemaskine Ozito Manualer

Ozito

Ozito ECS-406A Manual

6 Oktober 2024
Ozito

Ozito PXCCSK-4182 Manual

6 September 2024
Ozito

Ozito PXBPCK-1825 Manual

6 September 2024
Ozito

Ozito PXTCSK-2520 Manual

6 September 2024
Ozito

Ozito PXPRSS-018 Manual

5 September 2024
Ozito

Ozito PXBPCS-1815 Manual

5 September 2024
Ozito

Ozito JSW-6100U Manual

21 August 2024
Ozito

Ozito RTB-003 Manual

20 August 2024
Ozito

Ozito RSW-5200 Manual

17 August 2024
Ozito

Ozito JSW-4000U Manual

17 August 2024

savemaskine Manualer

Nyeste savemaskine Manualer

Einhell

Einhell GE-CS 18 Li Manual

15 Oktober 2024
MSW

MSW -TAS287 Manual

15 Oktober 2024
MSW

MSW T-SAW300 Manual

15 Oktober 2024
Makita

Makita 5603 Manual

14 Oktober 2024
FERM

FERM FKS-165 Manual

13 Oktober 2024
Einhell

Einhell TC-AP 650 E Manual

12 Oktober 2024
Einhell

Einhell TE-SM 36/210 Li Solo Manual

11 Oktober 2024
Einhell

Einhell BT-SM 2534 Manual

11 Oktober 2024
Hitachi

Hitachi C 7MFA(LA) Manual

9 Oktober 2024
Ferrex

Ferrex DX254TS Manual

5 Oktober 2024